Whispbar K364 Manuale utente
Fitting Kit
K364
ES
ESES
ES
Instrucciones de montaje para el
sistema de transporte.
F
FF
F
Instructions de montage pour Basic
Carrier
GB
GBGB
GB
Fitting Instructions for Basic Carrier
x 6 x 6 x 2 x 2
x 2 x 2 x 1 x 1
x 1 x 1
1
Revision No: 1.1B
Fitting Kit
K364
GB
MAX lbs
MAX lbs
W/P WHD W/P WHD
Mitsubishi
Montero , 5dr SUV 99- 06 EU 243 243 Pajero , 5dr SUV 00- 07 EU 243 243
Pajero LWB, 5dr SUV 99- 06 ZA 243 243 Pajero LWB, 5dr SUV Mar 07-+ NZ 243 243
Pajero LWB, 5dr SUV May 00-Oct 06 NZ 243 243 Pajero NM/NP, 5dr SUV May 00-Feb 07 AU 243 243
Pajero NS, 5dr SUV Mar 07-+ AU 243 243
2
Fitting Kit
K364
GB
First Time Installation
Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
This kit fits type A, B, C and D.
These instructions show type A crossbar
fitted. They also apply to type B, C and D.
Use keys to remove covers.
3
Fitting Kit
K364
GB
Use hex screwdriver to reverse adjusting
screw 10 turns.
Press adjusting screw and pull crossbar legs
out. Refer to the crossbar instructions for
crossbar adjustment.
Ensure each end of the crossbar is adjusted
equally.
Set bars to length (refer to the crossbar
instructions for crossbar adjustment).
Please check the rear of this manual for
information relating specifically to your
vehicle.
4
Fitting Kit
K364
GB
Tighten adjusting screw to 5 Nm (3.7 ft lb).
Remove clamp block by pressing backwards.
Select plastic internal block (from fitting kit)
and insert into foot.
5
Fitting Kit
K364
GB
Fitment
Locate plastic ditch mouldings on roof.
Run your finger along the inboard edge of
the moulding and locate fixed points.
It is important to put the clamps in the correct
position on the vehicle.
Letters refer to the part numbers stamped on
clamps.
Clamp Part Number:
A = 5221
B = 5223
C = 5224
Pull ditch moulding back towards you.
Hook clamps into the fixed points on the
vehicle.
6
Fitting Kit
K364
GB
Ensure internal clamp sits upright.
Repeat for all six positions.
Refer to the underside of the pad for the part
number.
It is important to put the pads in the correct
position on the vehicle.
Letters refer to the pad part numbers and
position.
Pad Part Number:
A = 11-04-218
B = 11-04-222
C = 11-04-223
D = 11-04-229
E = 11-04-230
7
Fitting Kit
K364
GB
Place pads on roof as per diagram. Screw
thread should be vertically through square
hole in pad.
Place crossbar foot over clamp bolt.
Tighten the red plastic knob. The side with
the nut showing should be facing up.
8
Fitting Kit
K364
GB
Ensure the red plastic knob is in the position
shown when fully tightened.
Repeat for all six positions.
Check crossbar is securely attached to the
vehicle.
Use keys to fit and lock covers
CAUTION:
CAUTION:CAUTION:
CAUTION:
Recheck all fasteners immediately after a load is
Recheck all fasteners immediately after a load is Recheck all fasteners immediately after a load is
Recheck all fasteners immediately after a load is
applied to the crossbars.
applied to the crossbars.applied to the crossbars.
applied to the crossbars.
Regularly check screws are tight.
Regularly check screws are tight.Regularly check screws are tight.
Regularly check screws are tight.
9
Fitting Kit
K364
GB
Maintenance
Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
Set crossbars a minimum distance of 700mm
(27 4/8") apart where no other distance is
specified in the fitting instructions. This is
especially important when carrying long
loads.
Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
Some sunroofs and radio antennae cannot
be used when the product is fitted.
Do not modify this product.
Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the fitting
instructions.
Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
Objects with pointed ends (skis) should be
carried with the pointed ends to the rear of
the vehicle.
Remove all loose or removable objects from
the load prior to loading.
Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
10
Indice
Lingue:
Altri manuali Whispbar Accessori per automobili
Whispbar
Whispbar K467W Manuale utente
Whispbar
Whispbar K102W Manuale utente
Whispbar
Whispbar K324 Manuale utente
Whispbar
Whispbar K525W Manuale utente
Whispbar
Whispbar K043W Manuale utente
Whispbar
Whispbar K945W Manuale utente
Whispbar
Whispbar K334W Manuale operativo e di installazione
Whispbar
Whispbar K057W Manuale utente
Whispbar
Whispbar K838W Manuale operativo e di installazione
Whispbar
Whispbar K998W Manuale operativo e di installazione
Whispbar
Whispbar K358W Manuale utente
Whispbar
Whispbar K687W Manuale operativo e di installazione
Whispbar
Whispbar K440W Manuale utente
Whispbar
Whispbar K507W Manuale utente
Whispbar
Whispbar K475W Manuale utente
Whispbar
Whispbar K700W Manuale utente
Whispbar
Whispbar K683W Manuale utente
Whispbar
Whispbar K317W Manuale utente
Whispbar
Whispbar K467W Manuale utente
Whispbar
Whispbar K345W Manuale utente
