Wildgame C8B5-7 Manuale utente
Invisible Infrared Digital
Cellular Scouting Camera
User’s Manual Model # C8B5-7
Includes
USB Cable 2 - Bungee Cords User Manual
Flextime Player
Software
Camera Unit Antenna
NOTE: Flextime Player Software is optional. Flextime files can be played by
using most media players
page 1
SIM card
RESOLUTION
FLASH
FLASH RANGE
SENSOR
SENSOR RANGE
IMAGE FORMAT
MEMORY
USB
IMAGE RESOLUTION
POWER SUPPLY
AUXILIARY POWER
ONBOARD POWER
HOUSING
MOUNTING
CELLULAR TYPE
SIM CARD
MAX: 8 MP
60 High Intensity Invisible IR LED’s
up to 70 feet
Passive Infrared Sensor (PIR) Motion and Heat
up to 60 feet
JPEG - Digital Still / AVI - Digital Video
up to 32GB SD Card (not included and required)
Class 4 and above recommended
5-PIN Mini USB style - included
High (8MP)
Medium (6MP)
Low (4MP)
4 D batteries (not included and required)
Alkaline recommended
External power port
Capacitor to retain Time and Settings
Weather resistant with rubber gaskets
2 Bungee cords - included
2G(GSM) and 3G(WCDMA), CDMA and CDMA2000 not supported
Mini-SIM (2FF) required
Note: Battery life will vary depending on camera settings as well as environ-
mental conditions. Camera settings such as shorter delay periods or even us-
ing Flextime mode are examples of settings that can reduce overall battery life.
Environmental conditions such as extreme cold can also influence battery life.
page 2
Features
Cell Mode can be activated only when the camera is set in PIR mode/im-
age. If the camera is set to Video or Flextime, the Cell mode will be disabled.
Setup
page 3
1. With the camera facing up, open the
battery compartment at the bottom
of the camera by turning them to
the left.
2. With the bottom of the camera
towards you, load 2 D batteries with
the positive ends towards you in
each chamber.
NOTE:
Do not mix old and new batteries. Do not mix alkaline,
standard (carbon-zinc) or rechargable (ni-cad, ni-mh,
etc.) batteries.
+
+
+
+
--
--
3. Close battery compartment cover
by turning them to the right.
4. Open the door at the bottom of the
camera by unlatching the locking
tabs.
page 4
5. To attach the antenna, place the
bottom of the antenna into the screw
hole at the top of the camera. Then
turn the antenna clockwise until it
is secure. Do not over tighten.
6. Load SD memory card (up to 32GB
not included) into the SD card slot
with the connectors facing down.
7. Load Mini-SIM (2FF) card into the
SIM card slot with the connectors
facing down.
IMPORTANT:
Make sure the camera is powered off before removing or
installing an SD card.
If you are using an SD card from other cameras, please
make sure to format the SD card in your computer prior
to use in your camera. New cards are ok to use straight
from the package.
Power On
page 5
1. To turn the unit ON, press and
release the power button.
2. Check the battery level icon to
ensure the batteries just installed
contain the proper charge level.
If so, you are ok to proceed with
camera use.
Note:
When Powered on or Woken up, the camera takes 5-10
seconds to check SIM card and/or Network settings. The
buttons are locked during this period.
UP
OK
L
R
DN
Test Mode
1. LCD Ready Mode: The camera will
automatically enter Ready Mode if
a button is not pressed for greater
than 30 seconds. The status lights
will illuminate for a total of 2
minutes.
2. PIR LED Status Light: During the
first 2 minutes of Ready Mode, the
red light will illuminate when a PIR
event is triggered. The red light will
blink for 2-3 seconds when photo
is taken during this first 2 minutes.
After 2 minutes all indicator
lights will turn off until a button is
pressed.
UP
OK
L
R
DN
page 6
Power Save
1. After 30 seconds without any
buttons being pushed, the LCD will
turn off and camera enters into
Power Save or Ready Mode.
2. The LCD screen can be awakened by
pressing the Power button briefly.
Note: The LCD will not “wake up” when
camera is writing to memory.
Date/Time
1. To change Date & Time, enter MENU
and press the UP,DN,L or R buttons
to navigate to the DATE & TIME icon
and press OK.
2. Press the UP or DN navigation
button to go up or down in sequence.
Press L or R to move to the next
digit.
3. When the Time & Date are set, press
OK to save and press OK again to go
back to the MENU.
UP
OK
L
R
DN
UP
OK
L
R
DN
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITY FLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
DATE & TIME
30
UP
OK
L
R
DN
__:_ _
__/__/__
TIME/D ATE
AM
MONTH DAYY EAR
PM
BACK
1
11 01 12
200
UP
OK
L
R
DN
__:_ _
__/__/ _ _
TIME/D ATE
AM
MONTH DAYY EAR
PM
BACK
1
11 01 1 2
20 0
Location
page 7
1. To change Location, enter MENU
and press the UP,DN,L or R buttons
to navigate to the LOCATION icon
and press OK.
2. Press the UP or DN navigation
button to go up or down in sequence.
Press L or R to move to the next
digit.
Image Type:Still
1. To change Image Type, enter MENU
and press the UP,DN,L or R buttons
to navigate to the Image Type icon
and press OK.
2. Press the L, R button to select
STILL and press OK. Then select the
Resolution and press OK. Select the
Exposure and press OK. Then select
the aspect and press OK.
When the Location is set, press OK
to save and press OK again to go
back to the MENU.
Save the location of the area the camera
was installed. This is for your reference
and is optional. If you do not wish to
name your location skip to the next step.
When the Image Type is set, press
OK to save and press OK again to go
back to the MENU.
3.
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITYFLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
LOCATION
UP
OK
L
R
DN
BACK
LO CA TION
________
AB
UP
OK
L
R
DN
BACK
LO CA TION
__ _ _____
AB C D
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITYFLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
IMAGE TYPE
3.
UP
OK
L
R
DN
BACK
STILL VIDE O
HI ME DL OW
REGULA R WIDE ANGLE
RESO LU TION
HI ME DL OW EXP C ONTRO L
IM AG E TY PE
UP
OK
L
R
DN
BACK
STILL VIDE O
HI ME DL OW
REGULA R WIDE ANGLE
RESO LU TION
HI ME DL OW EXP C ONTRO L
IM AG E TY PE
page 8
Image Type:Video
1. To change Image Type, enter MENU
and press the UP,DN,L or R buttons
to navigate to the Image Type icon
and press OK.
2. Press the L, R button to select
VIDEO and press OK. Then select
the Resolution and press OK. Then
select the length and press OK.
Trigger
1. To change Trigger, enter MENU and
press the UP,DN,L or R buttons to
navigate to the Trigger icon and
press OK.
2. Press the L, R button to select
Trigger Mode. Then select the OK
to save. If PIR is selected press OK
again to go back to the MENU.
TRIGGER:
PIR MODE: Takes a photo or video only when the
PIR sensor is triggered.
FLEXTIME (Time Lapse): Takes time lapse images
at set intervals during the key movement periods
of the day, depending on your Flextime settings.
BOTH: Both PIR and Flextime are active.
When the Image Type is set, press
OK to save and press OK again to go
back to the MENU.
This setting allows you to choose the
mode in which the camera will be
capturing images.
3.
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITY FLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
IMAGE TYPE
UP
OK
L
R
DN
BACK
STILL VIDE O
HD REGULAR
15 s 30 s1 m2 m VIDEO LENGT H
IM AG E TY PE
UP
OK
L
R
DN
BACK
STILL VIDE O
HD REGULA R
15 s 30 s1 m2 m VIDEO LENGT H
IM AG E TY PE
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITY FLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
TRIGGER
UP
OK
L
R
DN
BACK
PIRFlexTime BOTH
TRIGGER
PIR Sensitivity
page 9
1. To change PIR Sensitivity, enter
MENU and press the UP,DN,L or
R buttons to navigate to the PIR
Sensitivity icon and press OK.
2. Press the L, R button to select the
sensitivity and press OK to save.
Then press OK again to go back to
the MENU.
Image Type:Still
1. To change the Active Time, enter
MENU and press the UP,DN,L or
R buttons to navigate to the Active
Time icon and press OK.
2. Press the L, R button to select the
active time and press OK to save.
Then press OK again to go back to
the MENU.
PIR SENSE:
HI: The PIR detects the smallest movement.
MED: (Default) The PIR detects most
common size movements.
LOW: The PIR detects only larger
movements.
PIR ACTIVE:
24 HR: The PIR can be active at all times.
DAY: The PIR can be active in daylight hours
only.
NIGHT: The PIR can be active in nighttime
hours only.
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITYFLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
PIR SENSITIVITY
UP
OK
L
R
DN
BACK
HI ME D LO W
PIR SENSITIVIT Y
UP
OK
L
R
DN
BACK
ACTIVE TIME
LOCATION TRIGGER
DELAY
PIR SENSITIVITYFLEXTIME
+
™
+
DATE & TIME
30
PLAY BACK
IMAGE TYPE
VIEW ASSIST
ACTIVE TIME
UP
OK
L
R
DN
BACK
24 H R DAY NIGH T
AC TIVE T IM E
Indice
Altri manuali Wildgame Telecamera da ricognizione
Wildgame
Wildgame WRAITH Manuale utente
Wildgame
Wildgame R12B20-7 Manuale utente
Wildgame
Wildgame r12i20 Manuale utente
Wildgame
Wildgame Shadow Manuale utente
Wildgame
Wildgame C8B5 Manuale utente
Wildgame
Wildgame Innovations Mirage Manuale utente
Wildgame
Wildgame N2E Manuale utente
Wildgame
Wildgame Rival Manuale utente
Wildgame
Wildgame Razor Manuale utente
Wildgame
Wildgame W5ECA Manuale utente
Wildgame
Wildgame Cloak Pro Manuale utente
Wildgame
Wildgame t5i20 Manuale utente
Wildgame
Wildgame L10b5 Manuale utente
Wildgame
Wildgame Prizm Manuale utente
Wildgame
Wildgame W6EF Manuale utente
Wildgame
Wildgame W4E Manuale utente
Wildgame
Wildgame W3EA Manuale utente
Wildgame
Wildgame SC20i20-7 Manuale utente
Wildgame
Wildgame W6E Manuale utente
Wildgame
Wildgame FZ12 Manuale utente
