Windster RA-2390 Manuale utente
www.windsterhood.com
User’s Manual
RA-239036SS
Please read this operation manual thoroughly before
using your range hood. Store it in a safe location for
when you need to reference it in the future.
NOTE: This unit does not support
ductless operation.
For residential and indoor use only
WALL MOUNT SERIES
1
TABLE OF CONTENTS
Table of Contents
Safety Information ..............................................................2 – 3
Content Checklist .....................................................................4
Measurements ...........................................................................5
Preparation ............................................................................... 6
Installation ...........................................................................7 – 8
Installation Diagram ..................................................................9
Operation & Features .............................................................10
Cleaning & Maintenance .........................................................11
Troubleshooting ......................................................................12
Part List / Replacement ..........................................................13
Warranty / Contact Us .....................................................14 – 15
2
SAFETY INFORMATION
SAFETY INFORMATION
TO REDUCE THE RISK OF A FIRE, ELECTRICAL SHOCK,
AND/OR INJURY OBSERVE THE FOLLOWING:
• Unit is intended for indoor residential use only. If you should have questions,
contact the manufacturer at the address or telephone number listed in the
warranty.
• In case the unit should need to be cleaned or repaired, switch power off at
either breaker or by disconnecting the power cord from the outlet.
• Installation work and electrical wiring must be done by a qualified technician in
accordance with all applicable codes and standards, including fire-rated
construction.
• Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s guideline and safety standards
such as those published by the National Fire Protection Association (NFPA),
and the American Society of Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
• Because the unit is made of stainless steel, it may contain sharp edges. Be
careful to avoid cuts and abrasions by wearing protective gloves during
installation and cleaning.
• Before you begin to cut or drill into the wall, verify that there is no electrical
wiring or any other hidden electrical components.
• Ducted fans must always be vented to the outdoors.
• Use metal ductwork when possible.
• Do not use this fan with any solid-state speed control device and/or in-line
motor.
• The unit must be properly grounded before beginning operation.
3
SAFETY INFORMATION
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
• Regardless of heat level, never leave any surface materials unattended while
operating an open flame.
• Always turn hood ON when cooking at high heat or when flambéing food (i.e.
Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
• Depending on amount of usage, clean ventilating fans and filters frequently.
Grease should not be allowed to accumulate on fan or filter. For instructions
on the how to clean, see maintenance page.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE
EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING:
• SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then
turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not
go out immediately, EVACUATE AND CALL 911.
• NEVER PICK UP A FLAMING PAN — Doing so may result in serious burns
and possibly spread the fire.
• DO NOT USE WATER – Grease fire must be extinguished before further
action may be taken. Using water will agitate the grease and may cause a
violent steam explosion.
• Use a Fire Extinguisher ONLY if:
You have a Class ABC extinguisher, and you already know how to
operate it.
The fire is small and contained in the area where it started.
The fire department is being called.
You are able to safely control the fire with your back to an open exit. *
Based on “Kitchen Fire safety Tips” published by NFPA.
4
CONTENT CHECKLIST
CONTENT CHECKLIST
1. CONTENTS INCLUDED
a. (1) RA2390 series (36”) hood assembly with duct cover
b. (1) User’s manual
c. (1) 6” – 7” transition collar
d. (3) Magnetic baffle filters
e. (1) Screw packet
2. CONTENTS NOT INCLUDED
a. RA2390EXT (Extension duct cover)
b. RA2390CFMR (CFM reducer)
c. 6” / 7” Aluminum or metal piping
3. TOOLS REQUIRED (NOT INCLUDED)
a. Safety gloves
b. Safety glasses
c. Electric drill w/ starter bit
d. Utility knife
e. Spirit level
f. Measuring tape
g. Writing instrument (pen, marker, pencil)
h. Aluminum tape
5
MEASUREMENTS
6
PREPARATION
PREPARATION
1. BEFORE YOU START
**BE SURE YOUR UNIT WILL FIT YOUR CEILING HEIGHT**
a. Be sure you have all the content of your purchase and required tools for
this installation.
b. Installation may take at least 1 to 2 hours from start to finish.
c. Plan to use as few elbows or turns as possible for more efficient air flow.
d. Collar size may need to be increased if utilizing a long duct run.
e. At least 12” of vertical duct is required before any turn.
f. Do not try to install this unit by yourself, SERIOUS INJURY MAY OCCUR.
g. At least two people are needed for installation.
h. Hiring a certified installer and electrician is recommended.
2. LOCATION
a. Determine the exact location you where want to install the range hood.
b. Distance between cooktop and range hood should be between 27”-33”.
c. Range hood should be mounted at stated measurements to ensure
performance and lifespan of electrical components.
d. Correctly measure the dimension needed to install the unit.
3. HOOD
a. Inspect for any sign of defect or damage. (ie. scratches, dents, loose
seams, etc.)
b. Power up the unit to make sure it is working properly.
c. Remove the protective file on the baffle filters.
Use Fig. 1a on page 5 for unit measurements
Use Fig. 1b on page 5 for general measurements
INSTALLATION
7
INSTALLATION
1. WALL MOUNT INSTALLATION
a. Make sure all preparation steps are completed.
b. Determine your ceiling height to see if you need an extension.
i. Hood unit height = 4-3/4”
ii. Duct cover minimum height = 19”
iii. Duct cover maximum height = 35-1/2”
iv. (OPTIONAL) Extension duct cover height = 47”
c. Determine the location you want to install the range hood. (Fig. 2a)
d. Prepare back wall frame with cross wood support.
e. Mount the unit onto wall with mounting screws (not included)
f. Adjust the duct cover mounting bracket to your desired height.
g. Use a spirit level to ensure the balance of the hood is true.
h. (OPTIONAL) Use the conversion collar for 7” ducting.
i. Connect a 6” or 7” ducting to the collar of the hood.
j. Connect the exhaust piping to the outlet of the unit. (Fig. 2b)
k. Finish off by sealing the connection point with aluminum tape.
l. Slide the duct cover into the unit and adjust its height. (Fig. 2c)
m. Secure it with the (6) duct cover screws provided. (Fig. 2d)
2. EXTENSION DUCT COVER INSTALLATION
a. Replace the original inner duct cover piece with the extension.
b. Determine the desired height to mount the duct cover.
c. REPEAT “STEP F – M” from WALL MOUNT INSTALLATION section.
INSTALLATION
8
3. COLD WEATHER INSTALLATION (OPTIONAL)
a. Check with your local building codes to see if a CFM reducer is an
acceptable alternative to make-up air.
b. Remove the RA2390CFMR (CFM Reducer) and inspect for any sign of
defect or damage. (ie. Cracks, broken flips)
c. AFTER COMPLETING Step A – G of Section 1 WALL MOUNT
INSTALLATION
d. Place the CFM reducer onto the outlet of the unit and seal the connection
point with aluminum tape. (Be sure it is secure with no opening or gaps)
e. Connect a 6” or 7” ducting to the collar of the hood.
f. Connect the exhaust piping to the outlet of the unit. (Fig. 2b)
g. Finish off by sealing the connection point with aluminum tape.
h. Slide the duct cover into the unit and adjust its height. (Fig. 2c)
i. Secure it with the (6) duct cover screws provided. (Fig. 2d)
Installation diagram available on next page
9
INSTALLATION DIAGRAM
INSTALLATION DIAGRAM
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Windster Cappa di ventilazione
Windster
Windster RA-60TB30SS Manuale utente
Windster
Windster WS-62N Series Manuale utente
Windster
Windster RA-3030 Manuale utente
Windster
Windster LINER WS-69TB30 Manuale utente
Windster
Windster WS-4830SS Manuale utente
Windster
Windster WS-96TB30SS Manuale utente
Windster
Windster WS-3230SS Manuale utente
Windster
Windster Under Cabinet Series Manuale utente
Windster
Windster WINT024 Istruzioni per il montaggio
Windster
Windster RA-239036SS Manuale utente
Windster
Windster WS-58 series Manuale utente
Windster
Windster WS-5530SS Manuale utente
Windster
Windster LINER WS-69TB36 Manuale utente
Windster
Windster WS-5530SS Manuale utente
Windster
Windster WS-96TB Manuale utente
Windster
Windster WS-68N30SS Manuale utente
Windster
Windster R-18L42SS Manuale utente
Windster
Windster WS-268 Manuale utente
Windster
Windster RA-60TB30SS Manuale utente
Windster
Windster LINER WS-69TB30 Manuale utente
