Windster WS-6730SS Manuale utente

NOTE: PLEASE INSPECT HOOD

IMMEDIATELY UPON RECEIVING.

CLAIM OF DAMAGE AFTER 7 DAYS

OF DELIVERY WILL BE DENIED.

This unit is designed for indoor

residential use only. DO NOT USE

OVER A WOODGRILL OR MOUNT

IN OUTDOOR ENVIRONMENT.

www.windsterhood.com

User’sManual

WS-6730SS

WS-6736SS

Please read thisoperation manual thoroughly before

using your range hood. Store it in a safe location for

when you need to reference it in the future.

TABLE OF CONTENTS 1

Safety Information .......................................................... 2 – 4

Content Checklist................................................................... 5

Measurements ....................................................................... 6

Preparation............................................................................. 7

Installation.............................................................................. 8

Installation Diagram .............................................................. 9

Operation & Features .......................................................... 10

Cleaning & Maintenance .................................................... 11

Troubleshooting .................................................................. 12

Parts List / Replacement ..................................................... 13

Warranty / Contact Us.................................................14 – 16

2SAFETY INFORMATION

TO REDUCE THE RISK OF A FIRE, ELECTRICAL SHOCK,

AND/OR INJURY OBSERVE THE FOLLOWING:

•

Unit is intended for indoor residential use only. If you should have questions,

contact the manufacturer at the address or telephone number listed in the

warranty.

•

In case the unit should need to be cleaned or repaired, switch power off at

service panel and lock service disconnecting meansto prevent power from

being switched on accidentally. When the service disconnecting means cannot

be locked, securely fasten a prominent warning device, such as a tag, to the

service panel.

•

Installation work and electrical wiring must be done by a qualified technician in

accordance with all applicable codes and standards, including fire-rated

construction.

•

Sufficient air is needed for proper combustion and exhausting of gases

through the flue (chimney) of fuel burning equipment to prevent back drafting.

Follow the heating equipment manufacturer’s guideline and safety standards

such as those published by the National Fire Protection Association (NFPA),

and the American Society of Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

•

Because the unit is made of stainless steel, it may contain sharp edges. Be

careful to avoid cuts and abrasions by wearing protective gloves during

installation and cleaning.

•

Before you begin to cut or drill into the wall, verify that there is no electrical

wiring or any other hidden electrical components.

•

Ducted fans must always be vented to the outdoors.

•

The unit must be properly grounded and installed at the recommendedheight

before beginning operation.

•

To reduce the risk of fire, use only metal ductwork.

CAUTION: FOR GENERAL VENTILATING USE ONLY. DO NOT

USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS

AND VAPORS

SAFETY INFORMATION3

TO REDUCE THE RISK OF FIRE, OR ELECTRIC SHOCK, DO NOT

USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE.

•

Regardless of heat level, never leave any surface materials unattended

whileoperating an open flame.

•

Always turn hood ON when cooking at high heat or when flambéing food (i.e.

Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

•

Depending on amount of usage, clean ventilating fans and filters frequently.

Grease should not be allowed to accumulate on fan or filter. For instructions

on the how to clean, see maintenance page.

•

Never leave surface units unattended at high settings. Boil-overs may cause

smoking and greasy spillovers may ignite as result. Heat oils slowly on low or

medium settings.

•

Use proper pan size. Always use cookware appropriate for the size of the

surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:

•

SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then

turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not

go out immediately, EVACUATE AND CALL 911.

•

NEVER PICK UP A FLAMING PAN — Doing so may result in serious burns

and possibly spread the fire.

•

DO NOT USE WATER – Grease fire must be extinguished before further

action may be taken. Using water willagitate the grease and may cause a

violent steam explosion.

•

Use a Fire Extinguisher ONLY if:

You know you have a Class ABC extinguisher, and you already know

how to operate it.

The fire is small and contained in the area where it started.

The fire departmentisbeing called.

You are able to safely control the fire with your back to an open exit. *

Based on “Kitchen Fire safety Tips” published by NFPA.

SAFETY INFORMATION

PROP. 65 WARNING FOR CALIFORNIA RESIDENTS:

•

This product may contain chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

CONTENT CHECKLIST

1. CONTENTS INCLUDED

a. (1) 120V, 60Hz, 4A WS-69 series (30”/36”) hood assembly

b. (1) User’s manual

c. (2) LED lights (30”/36”)

d. (2) Baffle filters (30”)

(3) Baffle filters (36”)

2. CONTENTS NOT INCLUDED

a. WS-69CFMR (CFM reducer)

b. 6” / 7” Aluminum or metal piping

3. TOOLS REQUIRED (NOT INCLUDED)

a. Safety gloves

b. Safety glasses

c. Electric drill w/ starter bit

d. Utility knife

e. Philips screwdriver

f. Spirit level

g. Measuring tape

h. Writing instrument (pen, marker, pencil)

i. Aluminum tape

MEASUREMENTS

WS-6730SS

10-3/8''

6''

4''

2-1/2''

10-1/4''

11-3/8''

26''

27-3/4''

11-3/4''

10-3/8''

6''

4''

2-1/2''

10-1/4''

11-3/4''

33-7/8''

35-3/8''

11-3/4''

Wood Hood Cut-Out Size:

26-1/8" x 10-3/8"

Wood Hood Cut-Out Size:

34" x 10-3/8"

WS-6736SS

PREPARATION

1. BEFORE YOU START

**DO NOT INSTALL IF DAMAGED**

**RETURN OR EXCHANGE WILL BE DENIED IF INSTALLED**

a. Be sure you have all the content of yourpurchase and required tools for

this installation.

b. Installation may take at least 1 to 2 hours from start to finish.

c. Plan to use as few elbows or turns as possible for more efficient air flow.

d. Collar size may need to be increased if utilizing a long duct run.

e. At least 12” of vertical duct is required before any turn.

f. Do not try to install this unit by yourself, SERIOUS INJURY MAY OCCUR.

g. At least two people are needed for installation.

h. Hiring a certified installer and electrician is recommended.

i. Cold weather installation will require make-up air or a CFM reducer.

Check with your local building codes for more detail.

2. LOCATION

a. Determine the exact location you want to install the range hood.

b. Depending on the height of your ceiling, distance between cooktop and

range hood should be between 27”-33”.

c. Range hood should be mounted at stated measurements to ensure

performance and lifespan of electrical components.

d. Correctly measure the dimension needed to install the unit.

3. HOOD LINER

a. Inspect for any sign of defect or damage. ( i.e. scratches, dents, loose

seams, etc.)

b. Power up the unit to make sure it is working properly.

c. Remove the baffle filters and unscrew the fillers.

d. Remove the protective file on the baffle filters and fillers.

Use Fig. 1a and 1b on page 5 for measurements

INSTALLATION

DUCTED INSTALLATION

**DO NOT INSTALL CLOSER THAN 29” ABOVE COOKING SURFACE**

a. Make sure all preparation steps are completed.

b. Determine where you would like to mount the hood.

d. Lift the unit up flush against the wall.

e. Be sure the unit is leveled andparallel.

f. Using the screws and washers provided, tightly secure the unit against

the wall and the cabinet frame.

NOTE: Install additional screws through the back of the unit if necessary.

g. Use the conversion collar for 7” ducting. (OPTIONAL)

h. Connect 6” or 7” ducting to the collar of the hood.

i. Finish off by sealing the connection point with aluminum tape.

COLD WEATHER INSTALLATION (OPTIONAL)

NOTE: WS-69CFMR is only compatible with 6” top roundoutlet

a. Check with your local building codes to see if a CFM reducer is an

acceptable alternative to make-up air.

b. Remove the WS-69CFMR (CFM Reducer) and inspect for any sign of

defect or damage. (i.e. Cracks, broken/defective sections)

c. AFTER COMPLETING Step A – E of Section 1 DUCTED

INSTALLATION (Top roundoutlet)

d. Place the CFM reducer onto the outlet of the unit and seal the connection

point with aluminum tape. (Be sure it is secured with no opening or gaps)

e. Connect a 6” ducting to the collar of the CFM reducer.

f. Finish off by sealing other connection points with aluminum tape.

Installation diagram available on next page

c. Refer to diagram on page 9 to remove lower panel for installation.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Windster Cappa di ventilazione

Windster

Windster WS-5530SS Manuale utente

Windster

Windster RH-W30SS Manuale utente

Windster

Windster H30SS Manuale utente

Windster

Windster WS-268 Manuale utente

Windster

Windster RA-7630SS Manuale utente

Windster

Windster RA-3030SS Manuale utente

Windster

Windster LINER WS-69TB36 Manuale utente

Windster

Windster WALL MOUNT Series Manuale utente

Windster

Windster ISLAND Series Manuale utente

Windster

Windster RA-2390 Manuale utente

Windster

Windster RA-239036SS Manuale utente

Windster

Windster H Manuale utente

Windster

Windster RA=33 Series Manuale utente

Windster

Windster H-L Istruzioni per il montaggio

Windster

Windster RA-2290 Manuale utente

Windster

Windster HI30SS Manuale utente

Windster

Windster WS-4830SS Manuale utente

Windster

Windster WS-50E30SS Manuale utente

Windster

Windster R-18L36SS Manuale utente

Windster

Windster WS-38U30SS Manuale utente

Windster

Windster ISLAND Series Manuale utente

Windster

Windster RA-14L30SS Manuale utente

Windster

Windster WS-28TB30SS Manuale utente

Windster

Windster RA35U30SS Manuale utente

Manuali Cappa di ventilazione popolari di altre marche

emmeti

emmeti RECUPA MED A-140 Guida

Nibe

Nibe F135 Manuale utente

Kuppersberg

Kuppersberg INTRO 60 Istruzioni di installazione e manutenzione

Zephyr

Zephyr Spruce AK9834BS Guida all'installazione

Hisense

Hisense MH6INBG Manuale utente

Miele

Miele DA 1255 Manuale utente

Broan

Broan 46000 Manuale utente

GE Profile PV977 Istruzioni originali

FALMEC

FALMEC FFRIA24W5FS Manuale utente

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuale utente

Küppersbusch

Küppersbusch DX ISLA Manuale utente

ETNA

ETNA AV360RVS Manuale utente

JUNO

JUNO JDF603E6 Manuale utente

Miele

Miele DA 6708 D Manuale utente

Tricity Bendix

Tricity Bendix LE 150 Manuale

AEG

AEG X68163BV1 Manuale utente

AEG

AEG 125 D Manuale utente

Smeg

Smeg KSEV97X Manuale utente