WisyCom MTP60 Manuale utente

–––

MTP60 User Manual

Wideband Wireless

Professional Pocket

Transmitter

SN: ________________

Rev.01 (ref. FW 0.3)

Date: 22 October 2021

MTP60 User Manual

PRODUCT OVERVIEW

❶

OLED white display (128 x 64 pixels)

❽

IrDa interface

❷

4 setup buttons

❾

LED3 of recording

❸

battery compartment latch

❿

LED4 of recharging

❹

MIC connector (LEMO 1pin)

⓫

battery compartment

❺

Antenna connector (LEMO 3pin)

⓬

SD card slot

❻

LED1 for audio and recording

indication

⓭

USB-C connector

(for power and control)

❼

LED2 for RF and battery indication

❶

❷

❸

❹

❺

❿

❻

❼

❽

❾

⓫

⓬

⓭

MTP60 User Manual

LED INDICATIONS

LED 1 - audio and recording indication

Fixed green unit is modulating regularly

Blinking red Flash when audio is clipping

OFF (grey) if it doesn’t modulate

LED 2 - RF and battery indication

Fixed red with RF OFF

Fixed Green with RF ON

Blinking red when battery is discharging

LED 3 - recording

OFF (grey) when recording is OFF

Fixed red when recording is ON

LED 4 - recharging status

OFF (grey) when no recharging

Blinking orange when is under recharging

Fixed Green when recharge is completed

SETUP CONTROL

Use the 4 front buttons to navigate on the menu and enable quick setup:

SEL/ON:

oto switch ON the transmitter

oto enter on a sub-menu

oto save the parameter

EXIT/OFF:

oto switch OFF the transmitter

oto exit from a sub-menu

oto switch ON the transmitter without audio modulation

(only tone squelch)

UP/GAIN:

oto circle on the same level

oto enter on the GAIN settings (from STATUS menu)

DOWN/CH:

oto circle on the same level

oto enter on the CHANNEL settings (from STATUS menu)

SEL+GAIN: to enter on the menu

SEL+EXIT: to mute audio

EXIT+CH: to lock transmitter

GAIN+CH: to start recording

MTP60 User Manual

DISPLAY MENU

Setup menu are accessed in sequence:

MTP60 User Manual

PRESET menu

MTP60 can recall configuration presets.

o“Factory” recalls the Wisycom factory configuration.

o“USER” (U01, U02…) recalls the configuration saved by menu

o“PRESET” recalls preset saved with the Wisycom Manager or pre-configured by Wisycom

TUNING > Frequency menu

In this menu current channel/group and frequencies can be setup.

The name of the group is shown on the top right of the display.

Sync group is a quick self-settable channel synchronized by receiver (with SYNC group, on the top

right of the display is shown the name of the synchronized receiver).

Use arrows to change value and <ENTER> to confirm.

Using quick channel setup buttons (<CH>), it is possible to enter quickly in the tuning menu.

TUNING > Level menu

RF power can be setup to 20mW, 20mW Linear, 50mW or 100mW (depending on the Power profile,

see TUNING>Pwr Profile menu).

TUNING > Pwr on

Set to ON to activate the transmission. LED2 becomes fixed green when the transmitter is tuned and

RF power is ON.

AUDIO menu

With this menu it is possible to set all the audio parameters: gain, modulation (Narrowband or

Wideband), type of microphone, audio filters and the Tone.

SETTINGS menu

Use this menu to

oactivate the Bluetooth interface

oactivate the Irda interface

oset type of battery used

oconfigure LEDs behaviour

oconfigure brightness and time of display

INFO menu

Use this menu to check information about the transmitter (serial number, frequency range,

firmware and hardware version) and its status (voltage, temperature and alarms).

MTP60 User Manual

BATTERIES

MTP60 works with 2 x AA battery, Lithium, NiMh or KLIC8000 lithium (5.6 Wh) (select correct type

on setup controls). Battery status can be checked on internal OLED display or looking the LED2

status on front ❼.

BATTERY SUBSTITUTION

Open transmitter cover and insert batteries following polarity indicated.

Attention: always replace both the batteries

AUDIO CONNECTOR

3 PIN LEMO CONNECTOR

(use FVB.00.003.NLN on Mic)

MIC Mode:

Pin out

’2 wires’:

1=GND

3=AF

‘2 wires + bias’:

1=GND

3=AF+5.5V

‘3 wires’:

1=GND

2=5.5V

3=AF

‘2 wires &

phantom’:

1=GND

2=3.1V (power for PHA48 and PHA60)

3=AF

‘2 wires + bias &

phantom’:

1=GND

2=3. 1V (power for PHA48 and PHA60)

3=AF+5,5V

MTP60 User Manual

ACCESSORIES AND PARTS

AWF30-B1-507

For MTP60-US

Band 470 -547 MHz

Antenna label 507

AWF30-B1-590

For MTP60-US

Band 547 -663 MHz

Antenna label 590

AWF30-B8-950

For MTP60-US

Band 940 -960 MHz

Antenna label 950

CAL48

Cable to connect an MTP30 (with option /PHA) or

MTP40/40S to a PHA48 to use microphone with

XL3/48V connection

CAL120

AF cable (120cm), LEMO 3pole / XLR-3F connectors

PHA48

Plug-on for XLR3 Mic with 48V Phantom power.

To be used with CAL48 (connected to an MTP30/40/40S)

NEW REV2 with 4mA Phantom current!

Antenna label

MTP60 User Manual

TECHNICAL SPECIFICATIONS

Frequency ranges

from 470 to 1075 Mhz, depends on the country (see Configurations)

Switchable channels

2400 managed in 40 groups ofr 60 frequencies completely user customizable

Switching-window

Up to 362 MHz, depending on band (see Configurations)

Frequencies

Quartz PLL frequency synthesizer circuit (25 kHz step)

Frequency error

±2.5 ppm, in the rated temperature range

RF Power

switchable typ. 20 mW/ L20 mW / 50 mW /100 mW

note: in some countries high power can be disabled, for local norm!

Antenna connector

LEMO-F 1 pin

Modulation

wideband/narrowband FM, with digital audio conditioning (FPGA)

Nominal deviation

±40 kHz Wideband / ±25 kHz Narrowband

Peak deviation

±56 kHz Wideband / ±35 kHz Narrowband

Spurious emissions

< 2 nW

Telemetry feature

TX transmits also a digitally modulated sub-carrier, suitable for:

• tone-squelch operating

• remote battery monitoring

• optional PTT (push to talk) operation

Noise Reduction system

ENS - Wisycom Extended-Sound Optimized

AF bandwidth in NarrowBand

mode (NB)

Audio frequency response (dBa):

•45 Hz -17 KHz (3dB)

AF bandwidth in WideBand

mode (WB)

Audio frequency response (dBa):

•45 Hz -20 KHz (3dB)

Distortion

< 0.3 % (0.15 % typ.)

SND/D ratio (Analogue)

typ. 115 dB (A)rms with 40 kHz deviation; typ. 121 dB (A)rms with 56 kHz deviation Wideband

typ. 115 dB (A)rms with 25 kHz deviation; typ. 121 dB (A)rms with 35 kHz deviation

Narrowband

Audio input connector

LEMO 3pin

Audio input level

from -36 dBu (12mV RMS) to 26 dBu (15.5 V RMS) adjustable in 1 dB steps

Max input level

+26 dBu (15.5 V) at clipping, +20 dBu (7.75 V) at nominal level

Managing interface

Bluetooth 5 long range, USB-C, IrDA

LED

2 RGB LEDs indication with (red, green and blue)

LED 1

• Green unit is modulating regularly

• Red Flash when clipping

• OFF (grey) if it doesn’t modulate

• Fixed RED when recordin in ON

LED 2:

• Fixed Red with RF OFF

• Fixed Green with RF ON

• Blinking RED when battery is dicharging

Battery lifetime indication

10 steps

PTT function

Pin 3 of the AF connector can be setup to an external push button

Display

High contrast OLED white display (128 x 64 pixels)

Power supply

2 x AA battery, KLIC8000 lithium (5.6 Wh) or NiMh

Power consumption

250mA@ 2.6V average (display off, 100mW power)

Temperature range

-10 -+55 °C

Dimensions

75,7mm x 61,4mm x 19mm (HxWxD) without clip

Weight

Approx. 91 g. without batteries (133 g. with batt.)

MTP60 User Manual

Compliance

Model

In Compliance with

Max Power

Country

MTP60-EU

EN 301 489-1/-9

EN 600065

EN 300 422-1/-2

50mW

Europe

MTP60-EUX

EN 301 489-1/-9

EN 600065

EN 300 422-1/-2

EN 300 454-1/-2

100mW*1

Europe

MTP60-US

PART 74 & PART 15

FCC-ID: POUMTP60

100mW

USA

MTP60-CA

RSS-123, RSS-102

IC: 11967A-MTP60

100mW

Canada

*1MTP60-EUX is not an SRD device, thus it requires specific authorization by your local frequency authority!

Before putting the device into operation, please

observe the respective country-specific regulations!

MTP60 User Manual

MANUFACTURER DECLARATIONS

In compliance with the following requirements

RoHS Directive (2002/95/EC)

WEEE Directive (2002/96/EC)

Please dispose of the diversity transmitter at the end of its operational lifetime

by taking it to your local collection point or recycling center for such

equipment

Battery Directive (2006/66/EC)

The supplier batteries or rechargeable batteries can be recycled. Please

dispose of them as special waste or return them to your specialist dealer. In

order to protect the environment, only dispose of exhausted batteries.

ITALY ONLY

Obblighi di informazione agli utilizzatori

ai sensi dell’art. 13 del Decreto Legislativo 25 luglio 2005, n. 151 “Attuazione delle Direttive 2002/95/CE,

2002/96/CE e 2003/108/CE, relative alla riduzione dell’uso di sostanze pericolose nelle apparecchiature

elettriche ed elettroniche, nonché allo smaltimento dei rifiuti”

Smaltimento di apparecchiature elettriche ed elettroniche di tipo professionale

Il simbolo del cassonetto barrato riportato sull’apparecchiatura o sulla sua confezione

indica che il prodotto alla fine della propria vita utile deve essere raccolto separatamente

dagli altri rifiuti.

La raccolta differenziata della presente apparecchiatura giunta a fine vita è organizzata e

gestita dal produttore. L’utente che vorrà disfarsi della presente apparecchiatura dovrà

quindi contattare il produttore e seguire il sistema che questo ha adottato per consentire

la raccolta separata dell’apparecchiatura giunta a fine vita.

L’adeguata raccolta differenziata per l’avvio successivo dell’apparecchiatura dismessa al riciclaggio, al

trattamento e allo smaltimento ambientale compatibile contribuisce ad evitare possibili effetti negativi

sull’ambiente e sulla salute e favorisce il reimpiego e/o riciclo dei materiali di cui è composta

l’apparecchiatura.

Lo smaltimento abusivo del prodotto da parte del detentore comporta l’applicazione delle sanzioni am-

ministrative previste dalla normativa vigente.

Smaltimento batterie usate

Questo prodotto può contenere batterie. Questo simbolo apposto sulle batterie significa

che non possono essere smaltite insieme a normali rifiuti domestici, bensì devono essere

depositate negli appositi punti di raccolta delle batterie.

Iscrizione al Registro A.E.E. n. IT09100000006319

Altri manuali per MTP60

Indice

Altri manuali WisyCom Trasmettitore

WisyCom

WisyCom MTP40 Manuale utente

WisyCom

WisyCom MTH410 Manuale utente

WisyCom

WisyCom MTH400 Manuale utente

WisyCom

WisyCom MTB40S Manuale utente

WisyCom

WisyCom MTP40S Manuale utente

WisyCom

WisyCom MTP30 Manuale di istruzioni

WisyCom

WisyCom MTP40S Manuale utente

WisyCom

WisyCom CTK38 Manuale utente

WisyCom

WisyCom MPR30-IEM Manuale utente

WisyCom

WisyCom MTB40 Manuale utente

WisyCom

WisyCom RPU500-Tx Manuale utente

WisyCom

WisyCom MTK982 Manuale utente

WisyCom

WisyCom MTP61 Manuale di istruzioni

WisyCom

WisyCom MTP41 Manuale utente

WisyCom

WisyCom MTP51-JP Manuale utente

WisyCom

WisyCom CST38 Manuale utente

WisyCom

WisyCom MTP40 Manuale utente

WisyCom

WisyCom MTB40S Manuale di istruzioni

WisyCom

WisyCom MTP40S-US Manuale utente

WisyCom

WisyCom MTH400 Manuale utente

WisyCom

WisyCom MTP61 Manuale utente

WisyCom

WisyCom MTP41 Manuale utente

WisyCom

WisyCom MTB40 Manuale utente

WisyCom

WisyCom MTP40S Manuale di istruzioni

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente