Wittkopp Primor 2600 Guida utente

Primor 2600

Installer manual

Installation and commissioning instructions

en_02 P2600-Part 2b-Installer manual V1.01

1 / 6

Note:

On the cover sheet you can find warning information, and an explanation of the symbols and

terms used, together with the exclusion of liability.

Contents

General................................................................................................................................. 2

Preparation for installation..................................................................................................... 3

Installation dimensions - lock P2600.................................................................................. 3

Preparation of the boltwork / door...................................................................................... 3

Installation............................................................................................................................. 4

Wiring / installation................................................................................................................ 4

Connection of an analogue keypad ................................................................................... 5

Function test.......................................................................................................................... 5

Input of the opening code.................................................................................................. 6

Keypad test ....................................................................................................................... 6

Mount the keypad before installing the electronic lock. All the keypads of the Primor series

which support axis drive (RO, RE) can be used. All input units from the series basically

have thisfunction, however an additional handleor something similar is required to operate

the lock’s bolt drive. For information on how to install the keypads, please refer to "APxxxx

Part 2a- Keypad installer manual".

Primor 2600

Installer manual

Installation and commissioning instructions

en_02 P2600-Part 2b-Installer manual V1.01

2 / 6

General

P2600 series locks have standard

installation dimensions and can be installed

in all 4 installation positions (right, left, top,

bottom). They are designed for "scissor-

bolt" movements, i.e. for force absorption

by the bolt flanks.

They are intended to be installed in safes

made of metal.

Depending on the version, additional

locking elements (e.g. angle rail with bolts)

can optionally be attached to the bolt using

the existing holes. Proper functioning of the

lock and its connection must be ensured.

The electronic lock requires no

maintenance in a normal residential or

office environment. We recommend a

security and function test of the electronic

lock after around 10,000 closings.

The opening for the axle must not exceed

11.4 mm.

It is essential that the lock is protected

against attacks from outside. It is

recommended to protect the security-

relevant parts of the high-security lock

against access even when the safe door is

open.

Do not apply any lubricants or other

substances to the lock.

Always follow the following sequence for installation:

•Check the preconditions for installation

•Wiring / installation of the cables

•Disconnect the power supply

•Function test of the locking mechanism

•Perform all settings (user installation, delay time)

Ensure that the limit loads are not exceeded at any time.

You can find the corresponding values in Annex C "Technical data".

Primor 2600

Installer manual

Installation and commissioning instructions

en_02 P2600-Part 2b-Installer manual V1.01

3 / 6

Preparation for installation

Installation dimensions - lock P2600

Preparation of the boltwork / door

To install the lock, there must be three

threaded holes for fastening on the

boltwork or inside the safe door. The

electronic lock must be fastened with the

supplied screws or M6 or 1/4” cylinder

screws (min. strength class 8.8). The screw

length should be measured so that a

minimum screw-in depth of 5 mm is

possible.

Primor 2600

Installer manual

Installation and commissioning instructions

en_02 P2600-Part 2b-Installer manual V1.01

4 / 6

Installation

The retaining screws must be tightened in

such a way that a permanent and firm hold

is ensured.

Tighten the fastening screws with a

maximum torque of 3.5 - 5 Nm. To prevent

the screws from becoming loose, we

recommend using screw locking agents

(adhesive).

There must be no tension or pressure on

the lock bolt after installation.

Make sure there is sufficient clearance to

the locking point.

Wiring / installation

If the lock is operated outside the area of

validity of the VdS,then signal boxes,

external power supplies, etc. can be used

with the Anchor in addition to all the

analogue keypads that are compatible with

the Primor series.

The VdS approval is limited to operation

with input units fromthe Primor FS, FL, RO,

RE and Anchor LC series.

If the cable connection isnot routedthrough

the drive axis, the required hole / cable

route must be selected so that no access to

the lock body is possible through it by tools,

sensors or similar.

Holes for the cable aperture must be at

least 8 mm and a maximum of 11.4 mm.

Disconnect the power supply, including that from batteries, before starting any work or

making any changes to the wiring between the lock, keypad or signal boxes.

Primor 2600

Installer manual

Installation and commissioning instructions

en_02 P2600-Part 2b-Installer manual V1.01

5 / 6

Connection of an analogue keypad

Instructions for inserting the battery can be found in the operating instructions for the

corresponding Primor keyboard.

Function test

Carry out a function test after completing all

the mounting and installation work.With the

door open, you should open and close the

lock several times using the master code

that had been set at the factory.

To open the lock after release, turn the

keypad (RO) or operate the control knob

(RE):

The relationship between easy opening and

reliable closing can be set via the operating

lever of the boltwork.

The locking check is done by the position of

the input unit (RO) or, for input units with

operating toggle (RE), by the position of the

operating lever.

analogue keypad

e.g. Primor RO

Primor 2600

Installer manual

Installation and commissioning instructions

en_02 P2600-Part 2b-Installer manual V1.01

6 / 6

Input of the opening code

e.g. master factory code





=✓

→



The opening code can be entered

directly as described above, without

selection. The bolt is released for

approx. 3 seconds after a valid

code has been entered. Open the

safe within this period after entering

the code.

=



Keypad test

To make sure that all numeric keys are working properly, it is recommended to perform a final

keypad test using the function Menu 5.



☼Checking the menu system

Press the keys in the

sequence

…



=✓

Press each numeric key once. A

functional key is indicated by a

double signal tone.

A key that is not recognised is

indicated by a long signal tone and

the function test is terminated. The

system must be checked.

Indice

Altri manuali Wittkopp Serratura

Wittkopp

Wittkopp Primor Series Manuale utente

Wittkopp

Wittkopp 7800 Manuale utente

Wittkopp

Wittkopp FinKey Manuale utente

Wittkopp

Wittkopp OPTIMA 2648 Manuale utente

Wittkopp

Wittkopp Primor 1600 Guida utente

Wittkopp

Wittkopp Primor 100 Manuale utente

Wittkopp

Wittkopp Primor Level 25 Manuale utente

Wittkopp

Wittkopp Primor 1000 Manuale utente

Wittkopp

Wittkopp Primor 3000 Manuale utente

Wittkopp

Wittkopp ANCHOR Manuale utente

Wittkopp

Wittkopp Anchor 2600 Guida utente

Wittkopp

Wittkopp Anchor 7000 Guida

Wittkopp

Wittkopp Primor 1000 Guida utente

Wittkopp

Wittkopp Anchor 4000 Series Guida utente

Wittkopp

Wittkopp Insys 7202 Manuale utente

Wittkopp

Wittkopp ElCom 7205 Manuale utente

Wittkopp

Wittkopp GATOR F Manuale utente

Wittkopp

Wittkopp Primor P30 Series Manuale utente

Wittkopp

Wittkopp BlueCam greendot Manuale utente

Wittkopp

Wittkopp Anchor 4000 Series Manuale utente

Wittkopp

Wittkopp Anchor 7000 Manuale utente

Wittkopp

Wittkopp Primor Level 5 Manuale utente

Wittkopp

Wittkopp 1619 Manuale utente

Wittkopp

Wittkopp Primor Series Manuale utente

Manuali Serratura popolari di altre marche

Magic

Magic 105 Manuale utente

Gantner

Gantner GAT NET.Lock 7020 System Guida rapida

Dorma

Dorma Studio Classic Manuale utente

Securam

Securam ECSL-601 Manuale utente

Sudhaus

Sudhaus 3003 Manuale utente

Safety 1st

Safety 1st 48517 Manuale utente

Pado

Pado FDS-10 Manuale utente

Esco

Esco systeQ Series Manuale utente

COMPX

COMPX National D8951 Manuale utente

secureo

secureo Key Box Manuale utente

Stock Loks

Stock Loks C8713 Manuale utente

COMPX

COMPX 1T-058 Manuale del proprietario

Auslock

Auslock T11 Manuale utente

ELCOM

ELCOM 7205 Manuale utente

Stealth SAFES

Stealth SAFES ShadowVault Manuale utente

Knox

Knox KeySecure 5 Manuale utente

Kwikset

Kwikset 48334/01 Manuale utente

Metra Electronics

Metra Electronics Door Access Terminal Combo Manuale utente