Woodmizer LT15 AL-KO Guida

LT15 Trailer

Safety, Operation, Maintenance

& Parts Manual

LT15TRG Rev. A1.00 - A2.01

Safety is our #1 concern! Read and understand

all safety information and instructions before oper-

ating, setting up or maintaining this machine.

November 2010

Form #1729

ii 10doc111714 Table of Contents

Table of Contents Section-Page

SECTION 1 TRAILER INSTALLATION 1-1

1.1 Pre-Assembled Sawmill .........................................................................1-1

1.2 Unassembled Sawmill ............................................................................1-3

1.3 Up/Down & Feed Handle Relocation.....................................................1-4

1.4 Final Installation...................................................................................1-11

SECTION 2 TRAILER OPERATION 2-1

2.1 Preparing The Sawmill For Travel .........................................................2-1

2.2 Preparing The Sawmill For Operation ...................................................2-4

2.3 Loading A Log .......................................................................................2-7

SECTION 3 MAINTENANCE 3-1

SECTION 4 REPLACEMENT PARTS 4-1

4.1 Trailer (Complete) ..................................................................................4-1

4.2 Front Trailer Parts...................................................................................4-2

4.3 Rear Trailer Parts....................................................................................4-3

4.4 Outrigger Parts........................................................................................4-4

4.5 Winch Parts ............................................................................................4-5

4.6 Axle/Fender Parts ...................................................................................4-6

4.7 Saw Head Rest Pin/Bracket Parts...........................................................4-7

4.8 Up/Down Parts .......................................................................................4-8

INDEX I

Trailer Installation

Pre-Assembled Sawmill

Trailer Installation 1510doc111714 1-1

SECTION 1 TRAILER INSTALLATION

IMPORTANT! The trailer option is intended for use with LT15 sawmills Rev. E4.00

(LT15BS bed section Rev. E.00) and newer with three bed sections. LT15 sawmills prior

to Rev. E6.08 require modification to the mast to allow repositioning of the up/down sys-

tem (See Section 1.3).

1.1 Pre-Assembled Sawmill

If you are adding the LT15TRG trailer option to an assembled LT15 sawmill, the assem-

bled sawmill bed can be lifted onto the trailer frame. Be sure to use adequate manpower

and lifting equipment to safely lift and stabilize the sawmill during installation.

1. Disassemble the feed rope from the rear rope bracket and remove from the feed crank

pulley. Remove the rear feed rope bracket from the sawmill. Move the saw head to the

rear end of the bed and support with lifting equipment such as a forklift or hoist. Remove

the saw head from the bed and set aside.

2. Using adequate lifting equipment, lift the sawmill bed off the ground. Remove the legs.

See Figure 1-1.

3. Position the trailer next to the sawmill, oriented so the front of the sawmill is at the hitch

FIG. 1-1

Remove

legs from

sawmill

Disconnect feed rope,

remove bracket and

remove saw carriage

150193-1

Trailer Installation

Pre-Assembled Sawmill

1-2 1510doc111714 Trailer Installation

end of the trailer. Lower the trailer outriggers and use the jack handle to adjust the outrig-

gers to lift the trailer weight off the wheels and to level the trailer frame.

4. Disengage the trailer fender locking straps and lift the fenders from the trailer.

5. Lift the trailer winch assembly and pivot the winch down to the ground.

6. Pivot the saw head rest bracket down.

7. Position the sawmill onto the trailer frame, aligning the leg mounting holes with the holes

in the trailer frame. Secure the sawmill bed to the trailer frame with the provided mounting

bolts, bushings, washers and nuts.

See Figure 1-2.

8. Reassemble the saw head to the sawmill and replace the rear feed rope bracket. Leave

the feed rope disassembled until trailer installation is complete.

FIG. 1-2

150193-2

Adjust outriggers

to level trailer

frame

Jack

handle

½-13 x 6 ½” Hex

Head Bolt (6)

Bushing (8)

½-13 Hex

Nylon Lock

Nut (8)

½-13 x 3 ½” Hex

Head Bolt (2)

Pivot rest

bracket down

Lift and pivot

winch to ground

Lift fenders

from trailer

Washer (8) Secure bed to

trailer frame with

provided hardware

Trailer Installation

Unassembled Sawmill

Trailer Installation 1510doc111714 1-3

1.2 Unassembled Sawmill

If you are adding the LT15TRG trailer option to a new unassembled LT15 sawmill, the

sawmill bed can be assembled to the trailer frame. Be sure to use adequate manpower

and lifting equipment to safely lift and stabilize the sawmill during installation.

1. Lower the trailer outriggers and use the jack handle to adjust the outriggers to lift the

trailer weight off the wheels and to level the trailer frame.

2. Disengage the trailer fender locking straps and lift the fenders from the trailer.

3. Lift the trailer winch assembly and pivot the winch down to the ground.

4. Pivot the saw head rest bracket down.

5. Position the sawmill bed sections onto the trailer frame with the track position on the left

side of the trailer as viewed from the hitch end. Connect the bed sections as described in

the LT15 manual. Align the leg mounting holes with the holes in the trailer frame and

secure the bed to the trailer frame with the provided mounting bolts, bushings, washers

and nuts.

See Figure 1-3.

6. Refer to the LT15 manual to complete sawmill assembly and setup (skip the feed rope

installation until trailer installation is complete).

FIG. 1-3

150193-3

Adjust outriggers

to level trailer

frame

Jack

handle

½-13 x 6 ½” Hex

Head Bolt (6)

Bushing (8)

½-13 Hex

Nylon Lock

Nut (8)

½-13 x 3 ½” Hex

Head Bolt (2)

Pivot rest

bracket down

Lift and pivot

winch to ground

Lift fenders

from trailer

Washer (8)

Place bed sections

on trailer frame, connect

and secure with

provided hardware

Trailer Installation

Up/Down & Feed Handle Relocation

1-4 1510doc111714 Trailer Installation

1.3 Up/Down & Feed Handle Relocation

Because the sawmill sits higher when mounted to the optional trailer, parts are included

that allow you to relocate the up/down and feed crank handles to a lower position.

1. Move the saw head to rear of the sawmill and lower all the way down. Lower the saw

head until it rests on the bed to provide slack in the up/down chain.

2. Loosen the up/down chain lower sprocket mounting bolt and the chain tension bolt.

3. Disassemble the up/down chain master links from the mounting bracket and remove the

chain from the sawmill.

See Figure 1-4.

FIG. 1-4

150193-4

Loosen mounting

& tensioner bolts

Remove bottom

sprocket cover

Disassemble chain

from mounting bracket

Trailer Installation

Up/Down & Feed Handle Relocation

Trailer Installation 1510doc111714 1-5

4. Disassemble the feed handle/crank assembly from the sawmill mast.

5. Disassemble the up/down crank assembly and chain mounting bracket from the sawmill

mast.

See Figure 1-5.

FIG. 1-5

150193-5

Remove chain

mount bracket

Remove feed

handle & crank

Remove up/down

crank (shown with

optional gear reducer)

Trailer Installation

Up/Down & Feed Handle Relocation

1-6 1510doc111714 Trailer Installation

6. LT15 Rev. E4.00 - E6.07 only: Drill two 5/16” diameter holes in the mast vertical tube at

the locations specified. Tap the holes with 3/8-16 threads. Note: LT15 Rev. E6.08 include

a block with threaded hole welded at the upper location. LT15 Rev. E6.09 and newer

include a block with two threaded holes welded at this location.

See Figure 1-6.

FIG. 1-6

10”

1 ½”

½”

150194B

Drill 5/16” dia.

Tap 3/8-16

Trailer Installation

Up/Down & Feed Handle Relocation

Trailer Installation 1510doc111714 1-7

7. Use a C-clamp or vise to press the provided bearings into the up/down mounting bracket

housing. Be sure the bearings are oriented with the seals facing outward. To avoid dam-

aging the bearings, do not use a hammer to install.

8. Install the mounting bracket to the sawmill mast positioned two holes lower than the origi-

nal bracket. Use the existing hardware to secure the top of the bracket to the mast.

9. Install the new chain mount bracket at the bottom of the mast using the existing hardware

to secure.

See Figure 1-7.

FIG. 1-7

150193-6C

Press bearings

into housing

Use existing hardware

to mount bracket

Use existing hardware

to mount chain bracket

Trailer Installation

Up/Down & Feed Handle Relocation

1-8 1510doc111714 Trailer Installation

10. Disassemble the up/down crank assembly:

See Figure 1-8. Standard crank assembly: Use a 5/32” punch to remove the roll pin

securing the crank assembly to the sprocket/shaft weldment. Remove the crank assem-

bly and sprocket/shaft weldment from the mount bracket. Remove the two bolts, washers

and lock nuts to disassemble the dial from the mount bracket.

See Figure 1-9. Gear-reducer crank assembly: Disassemble the four bolts holding the

guard, dial and crank assembly to the mounting plate. Use a 5/32” hex wrench to remove

the two button head socket screws holding the sprockets to the hub. Use a 5/32” punch to

remove the roll pin securing the hub to the sprocket/shaft weldment. Remove the hub and

sprocket/shaft weldment from the mount bracket. Remove the two bolts and washers to

disassemble the mounting plate from the mount bracket.

FIG. 1-8

FIG. 1-9

150195-1

Crank Assembly

Roll Pin

Dial

Mount

Bracket

Sprocket/Shaft

Weldment

150196-1

Guard

Hub

Sprockets

Mounting

Plate

Crank

Assembly

Roll Pin

Dial

Mount

Bracket

Sprocket/Shaft

Weldment

Altri manuali per LT15 AL-KO

Indice

Altri manuali woodmizer Sega

woodmizer

woodmizer HR115 Manuale utente

woodmizer

woodmizer LX450 Series Guida

woodmizer

woodmizer LT40 Series Manuale utente

woodmizer

woodmizer LT28 Manuale di istruzioni

woodmizer

woodmizer SHR-T Series Manuale utente

woodmizer

woodmizer LT70HD Manuale di istruzioni

woodmizer

woodmizer LT70HD Manuale di istruzioni

woodmizer

woodmizer HR150 Manuale utente

woodmizer

woodmizer LT15 AL-KO Manuale di istruzioni

woodmizer

woodmizer LT15S3 E11S Manuale di istruzioni

woodmizer

woodmizer HR700 Series Manuale utente

woodmizer

woodmizer LT40HD Guida

woodmizer

woodmizer LX450DB-A Manuale utente

woodmizer

woodmizer LT60AHD Manuale di istruzioni

woodmizer

woodmizer LT40 Series Manuale di istruzioni

woodmizer

woodmizer LT40 MH Series Guida

woodmizer

woodmizer LX450 Series Manuale utente

woodmizer

woodmizer Autoclutch Option Manuale utente

woodmizer

woodmizer LT70 Super Hydraulic Manuale di istruzioni

woodmizer

woodmizer LX55 Guida

woodmizer

woodmizer LT40L AH Manuale di istruzioni

woodmizer

woodmizer LT40HD-H Hydro Manuale di istruzioni

woodmizer

woodmizer LT15S3 G13 Manuale di istruzioni

woodmizer

woodmizer LT30HD Manuale di istruzioni

Manuali Sega popolari di altre marche

RIDGID

RIDGID BS1400 Manuale utente

ATIKA

ATIKA BWS 400-2 Manuale utente

RGC

RGC FS20 Manuale utente

Makita

Makita M2300 Manuale utente

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuale utente

IMET Spa

IMET Spa SIRIO 370 AF-E Manuale utente

Optimum

Optimum OPTisaw CS 275 Manuale utente

Makita

Makita BPB180 Manuale utente

Stihl

Stihl MS 462 C-M Manuale utente

AEG

AEG TS 250 K Manuale utente

Meec tools

Meec tools 004665 Manuale utente

Makita

Makita LS1018L Manuale utente

Ryobi

Ryobi RCS1400 Manuale utente

DeWalt

DeWalt DCS391 Manuale utente

Sealey

Sealey SA72 Manuale utente

skilsaw

skilsaw SPT88 Istruzioni per il montaggio

Urrea

Urrea SI810 Dimensioni e guida di installazione

EINHELL

EINHELL BKG 210/1 Manuale utente

woodmizer LT15 AL-KO Guida

Manuali Sega popolari di altre marche