Woosim Systems PORTI-SB50 Manuale utente
http://www.woosim.com
All specifications are subjected to change without notice
MODEL PORTI-SB50
(Mobile Printer)
WOOSIM SYSTEMS Inc.
#501, Daerung Technotown 3th,
448, Gasan-Dong, GeumChun-Ku,
Seoul, Korea
Tel : +82-2-2107-3700
Fax : +82-2-2107-3707
URL: http://www.woosim.com
FCC Compliance Statements
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•Consult the dealer or an experienced radio / TV technician for help.
Warning : Your are cautioned that any change or modifications to the equipment not expressly
approved by the party responsible for compliance could void your authority to operate such
equipment.
http://www.woosim.com
C
Co
op
py
yr
ri
ig
gh
ht
t
PORTI-SB50 mobile printer operator’s manual.
Copyright ཱྀ2006 by Woosim System Inc.
All rights reserved.
The information contained in this manual is the property of Woosim System Inc. and may not be
reproduced in whole or in part without the prior written permission of Woosim System Inc.
Trademark
a registered trademark of Woosim System Inc.
All other trademark are the properties of their respective companies.
Caution
Some semiconductor devices are easily damaged by static electricity. You should turn the
printer ˈOFFˉ, before you connect or removed the cable on the rear side, in order to guard the
printer against the static electricity.
If the printer is damaged by the static electricity, you should turn the printer ˈOFFˉ.
Notice
The contents of this manual are subject to change without notice.
http://www.woosim.com
Introduction
The PORTI-SB50 is suitable designed for use with a growing variety of mobile devices.
RS232, IrDA(physical layer) and HPIR interfaces make the PORTI-SB50 the perfect comrade
for applications such as point of transaction warehousing, distribution, point of sales,
hospitality, gaming and healthcare.
The general features of PORTI-SB50 printer are as follows:
XPocket size (78mm x 131.5mm x 55mm).
XLight weight(200g) for true mobility.
XVery silent printing thru direct thermal printing method.
XHigh speed (50mm/sec, MAX)
XHigh resolution (203dpi, 8dot/mm)
XRS-232C, IrDA,HPIR interface
XEasier paper roll loading by CLAMSHELL design.
XEasier maintenance with self-diagnostic.
XMicrosoft Windows 98/ME/XP/2000 compatible.
XSupport bit-image(logo) download.
XFlow control : Software (XON/XOFF)
Hardware flow control not supported in printer.ଖ
G
http://www.woosim.com
Operating Precaution
Please follow the precautions below to enjoy and maintain the full performance of
the printer.
X
Using the Printer
ƔBe careful not to drop or bump the printer on a hard surface.
ƔDo not install the printer in direct sunlight or such areas.
Suitable environment for the use of the printer is as follows :
Operating temperature :ଝ-10°C to 40°C
Relative humidity : 10% toଝ90% (No condensation)
ƔDo not install the printer near devices that generate strong
electromagnetic fields such as a copy machine.
ƔDo not open the platen cover during printing .
ƔDo not remove or reinstall the communication cable during printing
or transmission.
ƔDo not touch the connectors of the communication cable and
to close up the Infrared transmitter /receiver during printing.
ƔSwitch the POWER OFF when not in use.
ƔDo not use alcohol or other solvent.
ƔThe AC adapter, the battery charger and the battery pack may
become warm when in use. This is normal and is not a malfunction.
ƔWhen the battery pack is used at low temperature, the length of time
the printer can be used may be shortened.
http://www.woosim.com
XThermal Paper Handling
ƔStore the thermal paper in a cool, dry and dark place.
ƔDo not rub the paper with hard object.
ƔDo not leave the paper with hard object.
ƔDo not allow plastic film, erasers, or adhesive tape to touch the paper
for long periods.
ƔDo not stack the thermal paper with diazo copies immediately
after copying or wet-type copies.
ƔDo not use chemical glue.
ƔAlways use the clean thermal paper.
http://www.woosim.com 6
CONTENTS
1. Outline ..............................................................................................................................7G
1.1. Model classifications ...............................................................................................7G
1.2. Specifications ..........................................................................................................8G
2. Setting up the printer ......................................................................................................9G
2.1. Printer & Accessories..............................................................................................9G
2.2. Printer Features.....................................................................................................10G
2.2.1. Part name.................................................................................................................10G
2.2.2. Dimension ................................................................................................................10G
2.3. Replacing paper roll ..............................................................................................11G
2.4. Power supply.........................................................................................................12G
2.4.1. Internal power supply...............................................................................................12G
2.4.2. Installing the Battery.................................................................................................12G
2.4.3. Recharging the battery.............................................................................................13G
3. Interface..........................................................................................................................14G
3.1. RS-232C................................................................................................................14G
3.2. Infrared data communication.................................................................................15G
4. Using the printer............................................................................................................16G
4.1. Control panel.........................................................................................................16G
4.2. Self test..................................................................................................................17G
4.3. Troubleshooting.....................................................................................................18G
5. Consumable parts .........................................................................................................20G
5.1. Recommended paper............................................................................................20G
5.2. Printing position.....................................................................................................20G
http://www.woosim.com 7
1
1.
.O
Ou
ut
tl
li
in
ne
e
1
1.
.1
1.
.M
Mo
od
de
el
lc
cl
la
as
ss
si
if
fi
ic
ca
at
ti
io
on
ns
s
PORTI-SB50 ( ) ( )
㩷
Model Name
Interface
None : RS-232C
IrDA / HPIR
Power
None : Dry Cell
(AAsize,4EA)
http://www.woosim.com 8
1
1.
.2
2.
.S
Sp
pe
ec
ci
if
fi
ic
ca
at
ti
io
on
ns
s
Item Specification
Print method Direct thermal line printing
Characters per line 48cpl (MAX)
Character size Eng. : 8×24dots , 9×24dots, 12×24dots, 16×24dots
Resolution 203dpi, 8dots/mm
Print width 2-inch (48mm, 384dots)
Print speed 50mm / sec (MAX)
Dimension 78 × 131.5 × 55 mm
Weight 200g (Except Dry cell)
Interface RS-232C
IrDA (Physical Layer) / HPIR
Paper roll Thermal roll paper (57mm wide, 50ø)
Barcodes Code128, Code39, I2/5, UPC, EAN, CODABAR
Receive buffer size 10K bytes
Battery Type Dry cell(AA size, 4EA)
(It is recommended that a high capacity of rechargeable battery be used.)
Battery Charger Output (9VDC/800mA)
Temperature -10°C ~ 40°C (operating)
-10°C ~ 70°C (storage)
Environment
Conditions Humidity 30% - 80% (operating)
10% - 90% (storage)
Mechanical 37,000,000 lines
MCBF (Mean Cycle
Between failure) Head Approximately 50 Km
http://www.woosim.com 9
2
2.
.S
Se
et
tt
ti
in
ng
gu
up
pt
th
he
ep
pr
ri
in
nt
te
er
r
2
2.
.1
1.
.P
Pr
ri
in
nt
te
er
r&
&A
Ac
cc
ce
es
ss
so
or
ri
ie
es
s
When unpacking your printer box make sure it contains the printer and all accessories.
If any accessories are missing or damage, please contact your dealer for assistance.
PORTI-SB50
ROLL PAPER
Indice
Altri manuali Woosim Systems Stampante
Woosim Systems
Woosim Systems WSP-DT380 Manuale utente
Woosim Systems
Woosim Systems WSP-SW25 Manuale utente
Woosim Systems
Woosim Systems WSP-R240 Manuale utente
Woosim Systems
Woosim Systems WSP-R231 Manuale utente
Woosim Systems
Woosim Systems WSP-DT380 Manuale utente
Woosim Systems
Woosim Systems PORTI-SC40N Manuale utente
Woosim Systems
Woosim Systems PORTI-KT40 Manuale utente
Woosim Systems
Woosim Systems PORTI-SW40 Manuale utente
Woosim Systems
Woosim Systems WSP-CP Manuale utente
Woosim Systems
Woosim Systems WSP-i350 Manuale utente
