Workrite Ergonomics Conform CONF-1SDA-WOB-S Manuale di programmazione

1 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

AConform Articulating Arm

Qty: 1 BM4 × 10 VESA

mount screw

Qty: 4

DPivot Cover Cap

Qty: 1

CM4 × 6 VESA

mount screw

Qty: 4

Parts Included

Required Parts Sold Separately Tools Required

Assembly & Installation Instructions:

Conform Articulating Arm CONF-1SDA-WOB-S

Attach Conform Articulating Arm to Selected Base Option

Remove Bolt and Washers from base (if not already removed.)

Place the Conform Arm (A) on the Base Pin.

Assemble Bolt with Washers as shown. Insert through the

bottom of the arm assembly and into the base. Tighten with

5mm Allen wrench. Be sure the arm is tight but rotates freely.

Snap Pivot Cover Cap (D) into top of arm assembly.

#2 Phillips head screwdriver

2.5 mm Allen wrench included with base

5 mm Allen wrench included with base

Selected base option with mounting hardware

Do not use on hollow core tables.

Do not rotate or suspend arm beyond table surface.

Do not exceed 17 lb.

M8 Flat Head Cap Screw M4 8mm Screw M4 12mm Screw M4 16mm Screw Spacer

Plastic Cap 7/32” Allen Wrench 1/8” Allen Wrench

Button Head Allen Cap ScrewPivot Pin

Steel WasherPlastic Pivot Washer

C-Clamp Mount shown

Remove

Replace

Bse Pin

2 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Attach the Monitor to the Monitor Arm VESA Plate

Remove the monitor from its stand. Keep the original screws

to mount to Conform Arm.

Attach the VESA plate to the VESA holes on your monitor. Use

the screws from your monitor if possible.

Monitor Capacity Adjustment (Silver Bolts)

If your monitor is too light or too heavy for the factory-

set capacity, the arm will raise, lower or tilt too easily. If

this is the case, you need to adjust the tension.

Adjusting Arm Capacity

To increase capacity(+) turn counter-clockwise using a

5 mm Allen Wrench (included with base) until the arm

reaches a balanced adjustment.

To decrease capacity(-) turn clockwise until the arm

reaches a balanced adjustment.

Adjusting Tilt Capacity

To increase capacity(+) turn clockwise using a 5 mm

Allen Wrench (included with base) until the monitor

reaches a balanced adjustment.

To decrease capacity(-) turn counter-clockwise until

the monitor reaches a balanced adjustment.

Remove

Tilt capacity

Arm capacity

Important Note: It is strongly recommended to use the mounting

screws provided by the monitor manufacturer if possible. If longer screws are

required, use either part (B) 10 mm, or (C) 6 mm screws supplied. Always use

the shortest screws possible to avoid damage to the monitor.

100 mm VESA standard, use

4 outer corner holes.

75 mm VESA standard, use

4 inner corner holes.

3 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Adjusting Pivot Tension (Black Bolts)

Carefully remove Pivot Cover Cap (D) at joint.

Setting Tension

If the arm is loose, turn the black adjustment

screw clockwise using a 5 mm Allen Wrench

(included with base) until the arm is tight and

pivots smoothly.

If the arm is tight and does not pivot, turn the

black adjustment screw counter-clockwise until

the arm pivots smoothly.

Locking Tension

Tighten the set screw with 2.5 mm Allen wrench

(included with base) to lock in the tension

level and prevent the joints from loosening or

tightening with use.

Replace Pivot Cover Cap (D) by snapping into top

of arm assembly.

Tighten

Loosen

Front

Shown on

C-Clamp Base

Remove

Replace

4 of 4 Workrite Ergonomics | 800.959.9675 www.workriteergo.com

Parts & Support

C-Clamp & Grommet Base ....................................................CONF-BSE-CCG-S

Two Piece C-Clamp & Grommet Base...................................CONF-BSE-TPCCG-S

Tool Bar & Slatwall Base .......................................................CONF-BSE-TSB-S

Wall Plate Base ......................................................................CONF-BSE-WP-S

Dual Arm Adaptor..................................................................CONF-ADPT-DA-S

Knoll®Antenna®Adaptor.....................................................CONF-ADPT-KA-S

14" Pole Base with C-Clamp & Grommet .............................CONF-PB-14CCG-S

28" Pole Base with Heavy Duty C-Clamp & Grommet .........CONF-PB-28HDCCG-S

Single Pole Mount Adaptor ...................................................CONF-ADPT-SPM-S

Dual Pole Mount Adaptor......................................................CONF-ADPT-DPM-S

Quick Release Adaptor..........................................................MON-ADPTVQR-W-B

Technical Support: Please call Workrite Technical Support while at the Workrite product. (800) 969-9675 option 2.

Cable Management

Upper Arm: Insert cables into the recessed area under the upper arm

by pushing the cables through the clips.

Lower Arm: Remove the cover by sliding it up, then o. Secure cables

with Hook & Loop strips. Slide cover down to secure.

Desk Base: Run the cable from lower arm to the back of

the base. Put cables into the cable clip.

Note: Leave suicient slack in the cables to allow

free movement of arm.

1500245 Rev F

Hook & Loop

Strip

Hook

& Loop

Strip

High

point

O

✓

Altri manuali Workrite Ergonomics Rack e supporto

Workrite Ergonomics

Workrite Ergonomics Willow Dual Guida rapida

Workrite Ergonomics

Workrite Ergonomics Conform CONF-1SDS-WOPB-S Manuale di programmazione

Workrite Ergonomics

Workrite Ergonomics Sequoia SQ-422 Manuale utente

Workrite Ergonomics

Workrite Ergonomics Sequoia SQ-303 Manuale utente

Workrite Ergonomics

Workrite Ergonomics Conform LT CONF-LT-2SA-TPCG-G Manuale di programmazione

Workrite Ergonomics

Workrite Ergonomics CONF-2SDS-WOPB-S Manuale di programmazione

Workrite Ergonomics

Workrite Ergonomics PEAK-1SA-CCG-S Manuale utente

Workrite Ergonomics

Workrite Ergonomics Metro 6 Manuale di programmazione

Workrite Ergonomics

Workrite Ergonomics Sequoia SQ-211 Manuale utente

Workrite Ergonomics

Workrite Ergonomics CONF-3SDS-WOPB-S Manuale di programmazione

Workrite Ergonomics

Workrite Ergonomics CONF-BSE-WP-S Manuale di programmazione

Workrite Ergonomics

Workrite Ergonomics Conform Sit-to-Stand Arm Manuale di programmazione

Workrite Ergonomics

Workrite Ergonomics Sequoia SQ-633 Manuale utente

Workrite Ergonomics

Workrite Ergonomics Sequoia SQ-101 Manuale utente

Workrite Ergonomics

Workrite Ergonomics CONF-ADPT-DA-S Manuale di programmazione

Workrite Ergonomics

Workrite Ergonomics Sequoia SQ-523 Manuale utente

Workrite Ergonomics

Workrite Ergonomics Sequoia SQ-202 Manuale utente

Workrite Ergonomics

Workrite Ergonomics Conform Base CONF-BSE-TSB-S Manuale di programmazione

Workrite Ergonomics

Workrite Ergonomics PEAK-2DA-CCG-S Manuale utente

Workrite Ergonomics

Workrite Ergonomics Sequoia SQ-312 Manuale utente

Workrite Ergonomics

Workrite Ergonomics CONF-2SDA-WOB-S Manuale di programmazione

Workrite Ergonomics

Workrite Ergonomics CONF-ACC-1EXT-S Manuale di programmazione

Workrite Ergonomics

Workrite Ergonomics 920 Series Manuale utente

Workrite Ergonomics

Workrite Ergonomics Sequoia SQ-413 Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente