Worx Landroid Manuale utente

Worx Landroid

Maintenance Sheet

A Steelfort Product steelfort.co.nz

Worx Landroid

Maintenance Sheet

1. How to manage ordinary Landroid

maintenance?

With minimal maintenance, your Landroid will operate smoothly, season after season

Your Landroid works hard and needs to be cleaned and checked from time to time. This section of our

guide helps you keep Landroid in good shape so it can last for years without troubles. Here’s how to

take care of your Landroid:

Keep it sharp

Landroid does not cut grass like other mowers. Its cutting blades are razor sharp on 2 edges and ro-

tate in both directions for maximum cutting capacity.

• The blade turning disc makes a clockwise and counterclockwise rotation at random to use both cut-

ting edges and minimise the frequency of replacing the blades

• Each cutting blade will last up to 2 months when it is programmed to mow every day

• Always check to see if the blades are chipped or damaged and replace them if they are

• When the cutting blades are dull and worn out, they should be replaced with the spare blades pro-

vided with your Landroid.

Spare blades are also available at your nearest Landroid retailer.

WARNING! Before cleaning, adjusting, or replacing the blades, turn your Landroid OFF and remove

the battery. Always wear protective gloves.

Replacing the Blades

1. Remove the battery

2. Gently ﬂip the Landroid over

3. Take the screws o the blades with a screwdriver

4. Firmly screw on the new blades

5. Reﬁt the battery

When ﬁtting new blades, make sure you replace ALL the blades.

Always use new screws when ﬁtting blades. This is important to ensure blade retention and balance

the blade turning disc. Failure to use new screws could cause serious injury

Attention: After screwing the blade to the blade disc, make sure the blade is able to spin freely.

A Steelfort Product steelfort.co.nz

Worx Landroid

Maintenance Sheet

Keep it clean

Your Landroid should be cleaned regularly. This helps keep it in good condition, especially removing

dirt, debris and the build-up of grass from daily mowing. Turn Landroid o before cleaning it. For extra

safety, remove the battery.

WARNING! DO NOT use a hose, high pressure washer or otherwise pour running water on your

Landroid. High pressure water can go inside the sealings and damage electronic and mechanical

parts.

Cleaning the upper body

• Clean with a spray bottle ﬁlled with water. Don’t use solvents or polishers

• Use a brush or a clean cloth to remove built-up dirt

Cleaning the bottom

• Flip Landroid upside down

• Remove debris and grass clippings using a brush to remove

• Be careful not to touch the blades with your hands. Wear gloves for protection

• Clean the blade disc, the chassis and the front wheel(s) thoroughly with a soft brush or moist rag

• Rotate the blade disc to ensure it rotates freely. Remove any obstructions. Remove any lodged

debris so that they don’t cause a crack in the blade disk. Even the tiniest crack eects mowing

performance

• Check the blades spin freely around the ﬁxing screws. Remove any obstructions

Cleaning the drive wheels

• Remove mud from wheels with a brush in order to ensure good grip of the tread

Clearing the charging contacts

• Clean the contact pins located on the charging base and the charging strips located on the Landroid

using a cloth

• Periodically remove any build-up of grass clippings or debris around the contact pins and the

charging strips to ensure Landroid successfully charges each time

A Steelfort Product steelfort.co.nz

Worx Landroid

Maintenance Sheet

2. How to repair the boundary wire?

This tutorial will help you to proceed in case boundary wire is broken

Boundary wire can be repaired in dierent way, we suggest you to follow the one of the two listed

below taking in to account your personal skills.

Attention: it is not recommended to simply splice the boundary wire with insulating tape or use a

screw terminal block for connection. A broken circuit may occur after a period of time as soil moisture

can oxidize the wire.

How to repair boundary wire (beginners option)

You can encounter two cases: the wire is cut or the wire is damaged. In this second case, you must

cut and take away the damaged part.

Please read the steps below to proceed.

Then to proceed you will need:

A. the two waterproof boundary wire connectors that are in your Landroid box

B. a small piece of spare wire

Proceed as follows and remember to not strip anyone of the wires you will use.

1. Insert one end of the broken boundary wire into any hole of the connector

A Steelfort Product steelfort.co.nz

Worx Landroid

Maintenance Sheet

2. Use the small piece of new boundary wire and connect it to one of the two remaining holes on the

connector

3. Press the connector ﬁrmly by using a pair of pliers

4. Insert the other end of the spare wire and the other end of the boundary wire using the second

connector. Press the connector ﬁrmly by using a pair of pliers.

5. Proceed with burying again the boundary wire and secure it to the ground with a peg.

Alternatively, advanced users can tin the soldering wire, taking care to cover the wire with self-

amalgamating tape and eventually cover everything with an insulating tape.

A Steelfort Product steelfort.co.nz

Worx Landroid

Maintenance Sheet

3. How to update Landroid ﬁrmware

This maintenance article will help you to keep your Landroid ﬁrmware always up to date

Landroid is always improving and new software versions are made available for free.

Always keep Landroid ﬁrmware updated to make the most of your machine.

The update can be done Over-the-Air if your Landroid is connected to our cloud via Wi-Fi, Find My

Landroid or RadioLink. If not connected, it can be managed via a USB stick.

By keeping the auto-update enabled, you won’t have to push a button to keep it updated, everything is

done automatically as soon as new ﬁrmware is released and your Landroid is in the charging station.

How to know when a new ﬁrmware release is available

Once you’ve registered your Landroid on our account web panel, you can check the latest version

available. If you’ve connected Landroid with the app, you can check it the “Update” section.

Check which ﬁrmware version you have

If you are using the Landroid app, the ﬁrmware version is displayed on menu/device.

If you have a Landroid with an LCD display, the ﬁrmware version is always displayed on the left-hand

side of the display when you power on your Landroid.

If you have a Landroid 2019/2020 with the 7-segments display, please:

press and hold the Power and OK buttons together — a beep will sound.

a number will appear on the display that indicates the version number.

A Steelfort Product steelfort.co.nz

Worx Landroid

Maintenance Sheet

If you have a Landroid S 2017/2018 the software version is shown only in the app. (menu/device info)

OTA (Over-the-Air) updates

If you have auto-update disabled, please open the “Update” section of the app, if new ﬁrmware is

available you’ll be able to send the update to your Landroid. Please make sure that your Landroid is

under Wi-Fi coverage when sending updates.

Manual updates (via USB)

Depending on which Landroid model you have please refer to the following tutorials:

Landroid S, M500, L1000 2019/2020 (7-segments display): WR139E

If you haven’t registered your mower for the warranty extension yet, the system will ask you to do it ﬁrst.

Once registered, select your mower model from the list, then download the lates available ﬁrmware on

your computer by clicking the download button.

Now follow the instructions here:

1. Get a USB stick, insert in your computer and format it FAT32. Small capacity USB sticks (e.g. 2, 4 or

8GB) work better for this purpose.

2. Copy the ﬁle as it is (no need to unzip it) from your computer to the USB stick.

3. Open the rear cover of the robot and locate the USB port.

4. Switch the robot o.

5. Insert the USB stick in the port, then power the robot on.

6. The machine will start to download the ﬁrmware. When the robot displays “USB”, remove the USB

stick.

7. Now the ﬁrmware update process starts. Once it is ﬁnished, the robot restarts and you will be asked

to insert the PIN.

Enjoy your newly updated Landroid.

A Steelfort Product steelfort.co.nz

Worx Landroid

Maintenance Sheet

Landroid M, L 2019/2020 (digital display): WR140, WR150

If you haven’t registered your mower for the warranty extension yet, the system will ask you to do it ﬁrst.

After that please select your mower from the list, and download the latest available ﬁrmware by clicking

on the download button.

1) Please copy the ﬁle as it is (no need to unzip it) in an empty and formatted FAT32 USB stick. Older

ones (2/4/8GB ) are preferred.

2) The USB port is in the rear of the robot.

3) With the unit powered o, insert the USB then power the unit ON.

4) Follow the instructions on the display.

A Steelfort Product steelfort.co.nz

Worx Landroid

Maintenance Sheet

4. How to deal with a completely

discharged Landroid?

Tutorial to act in case of emergency charging need

If you Landroid does not power up when turned on it can be than Landroid it is completely discharged

due to an unexpected event. This is a rare vent that can be easily ﬁxed.

In this case you should operate an emergency charge, depending on your Landroid model please follow

the steps below:

S, M, L 2019/2020

WR130E, WR141E, WR142E, WR143E, WR147, WR153E, WR155E, WR140, WR150

Manually dock it to charge, making sure the contact pins touch in the middle the contacts on the

charging base, and the emergency charging will start.

When the charge is completed, power Landroid on and it will operate accordingly to its schedule.

S 2017/2018

WR101SI, WR102SI, WR104SI, WR105SI, WR106SI, WR110MI, WR100SI, WR101SI.1, WR102SI.1, WR103SI,

WR104SI.1, WR105SI.1, WR106SI.1, WR110MI.1, WR115MI, WR090S, WR091S, WR092S, WR093S, WR094S,

WR095S, WR096S

Please proceed as per steps below:

1. Turn your Landroid o

2. Manually dock it to charge. The charging station LED will turn from green to red, the battery symbol

will blink red and green for about an hour and half. The charge is completed when the red LED on the

base truns green

You don’t need to wait for the entire charge cycle, Landroid can go back to work after approximately

one hour

3. Turn the power on

Attention: when an emergency charge is performed your Landroid remains in standby mode, waiting for

instructions even once the main switch has been turned on.

A Steelfort Product steelfort.co.nz

Worx Landroid

Maintenance Sheet

In order to restore full functionality, you have two options:

A. Press START then OK. Landroid will start work immediately

B. Take your Landroid out of the base and press HOME/OK. Landroid will return to base and operate

according to schedule.

M, L 2016/2018

WG757E, WG796E.1, WG797E.1, WG798E, WR111MI, WR112MI, WG799E, WR113MI, WG754E, WG755E,

WG756E, WG790E.1, WG791E.1, WG792E.1, WG793E.1, WG758E

1. Place manually your Landroid on the charging base

2. As the led of the charging base will light on, please turn on your Landroid

3. The charge is completed when the red LED on the base turns green. Landroid will then operate

accordingly to its schedule.

Altri manuali per Landroid

Indice

Altri manuali Worx Taglia erba

Manuali Taglia erba popolari di altre marche

RHINO

RHINO 1958 Manuale utente

Wolf Garten

Wolf Garten Compact plus 40 B Manuale utente

Cub Cadet

Cub Cadet LTX 1045 Manuale utente

Craftsman

Craftsman 917.378461 Manuale utente

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuale utente

Challenge

Challenge CH18V2 Istruzioni operative

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuale utente

DEWEZE

DEWEZE ATM-725 Manuale operativo

Weed Eater

Weed Eater 180083 Manuale utente

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuale utente

Better Outdoor Products

Better Outdoor Products Quick Series Manuale utente

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuale operativo

MTD

MTD 795, 792, 791, 790 Manuale utente

Toro

Toro Groundsmaster 3505-D Manuale utente

Dennis

Dennis FT 610 Manuale utente

AIRFORCE

AIRFORCE F-15 Gen 3 Manuale utente

MTD

MTD 126-220-000 Manuale utente

Toro

Toro 74806 Manuale utente