WTI TSM-8 Manuale utente

WTI Part No. 14023

Rev. J

TSM Series

Serial Console Servers

RSM Series

Remote Site Managers

RSM-8R8 Series

Remote Site Managers with Power Control

User's Guide

Warnings and Cautions:

Installation Instructions

Secure Racking

If Secure Racked units are installed in a closed or multi-unit rack assembly, they may

require further evaluation by Certification Agencies. The following items must be

considered.

1. The ambient within the rack may be greater than room ambient. Installation

should be such that the amount of air flow required for safe operation is not

compromised. The maximum temperature for the equipment in this environment is

45°C. Consideration should be given to the maximum rated ambient.

2. Installation should be such that a hazardous stability condition is not achieved due

to uneven loading.

Input Supply

1. Check nameplate ratings to assure there is no overloading of supply circuits that

could have an effect on overcurrent protection and supply wiring.

2. When installing 48 VDC rated equipment, it must be installed only per the following

conditions:

A. Connect the equipment to a 48 VDC supply source that is electrically isolated

from the alternating current source. The 48 VDC source is to be connected to

a 48 VDC SELV source.

B. Input wiring to terminal block must be routed and secured in such a manner

that it is protected from damage and stress. Do not route wiring past sharp

edges or moving parts.

C. A readily accessible disconnect device, with a 3 mm minimum contact gap,

shall be incorporated in the fixed wiring.

Grounding

Reliable earthing of this equipment must be maintained. Particular attention should

be given to supply connections when connecting to power strips, rather than direct

connections to the branch circuit.

No Serviceable Parts Inside; Authorized Service Personnel Only

Do not attempt to repair or service this device yourself. Internal components must be

serviced by authorized personnel only.

• ShockHazard-DoNotEnter

• LithiumBattery

CAUTION:Dangerofexplosionifbatteryisincorrectlyreplaced.Replace

onlywithsameorequivalenttyperecommendedbythemanufacturer.

Discardusedbatteriesaccordingtothemanufacturer'sinstructions.

Warnings and Cautions

Disconnect Power

If any of the following events are noted, immediately disconnect the unit from the outlet

and contact qualified service personnel:

1. If the power cord becomes frayed or damaged.

2. If liquid has been spilled into the device or if the device has been exposed to rain

or water.

Disconnect Power Before Servicing

Before attempting to service or remove this unit, please make certain to disconnect the

power supply cable from the power source.

Two Power Supply Cables

Note that TSM-DPS series units and RSM-8R8 series units feature two separate power

inlets, and a separate power supply cable for each power inlet. Make certain to

disconnect both power supply cables from their power source before attempting to

service or remove the unit.

Modem Cables

CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger (e.g., 24 AWG) UL

Listed or CSA Certified Telecommunication Line Cord.

iii

Agency Approvals

FCC Part 15 Regulation

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation

WARNING: Changes or modifications to this unit not expressly approved by

the party responsible for compliance could void the user’s authority to operate

the equipment

EMC, Safety, and R&TTE Directive Compliance

The CE mark is affixed to this product to confirm compliance with the following

European Community Directives:

• CouncilDirective89/336/EECof3May1989ontheapproximationofthelaws

ofMemberStatesrelatingtoelectromagneticcompatibility;

 and

• CouncilDirective73/23/EECof19February1973ontheharmonizationof

thelawsofMemberStatesrelatingtoelectricalequipmentdesignedforuse

withincertainvoltagelimits;

 and

• CouncilDirective1999/5/ECof9Marchonradioequipmentand

telecommunicationsterminalequipmentandthemutualrecognitionoftheir

conformity.

Industry Canada - EMI Information

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

This product meets the applicable Industry Canada technical specifications

The Ringer Equivalence Number is an indication of the maximum number of devices

allowed to be connected to a telephone interface. The termination on an interface may

consist of any combination of devices subject only to the requirement that the sum of

the RENs of all the devices does not exceed five.

Table of Contents

1. Introduction.............................................................1-1

2. UnitDescription..........................................................2-1

2.1. Front Panel (TSM Series) ................................................2-1

2.2. Back Panel (TSM Series) ................................................2-2

2.3. Back Panel (TSM-DPS Series and TSM-DPE Series) . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.4. Front Panel (RSM Series) ................................................2-5

2.5. Back Panel (RSM Series) ................................................2-6

2.6. RSM-8R8 Series - Front Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

2.7. RSM-8R8-DE Series - Front Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8

2.8. RSM-8R8 Series - Back Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

2.9. Front Panel Button Functions ............................................2-10

3. GettingStarted..........................................................3-1

3.1. Apply Power to the TSM/RSM ............................................3-1

3.2. Connect Your PC to the TSM/RSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.3. Communicating with the TSM/RSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3.4. Connecting Ports and Switching Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

4. HardwareInstallation.....................................................4-1

4.1. Connecting the Power Supply Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.1.1. Connect the TSM/RSM to Your Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.1.2. Installing the Power Supply Cable Keeper . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.1.3. DC Powered Units ...............................................4-2

4.2. Connecting the Network Cable ...........................................4-2

4.3. The Internal Modem Port ................................................4-2

4.4. Connection to Switched Outlets (RSM-8R8 Series Units Only) . . . . . . . . . . . . . . . . . . . 4-3

4.5. Connecting Devices to the TSM/RSM Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

5. BasicConfiguration......................................................5-1

5.1. Communicating with the TSM/RSM Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5.1.1. The Text Interface ...............................................5-1

5.1.2. The Web Browser Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

5.1.3. Access Via PDA .................................................5-3

5.2. Configuration Menus ...................................................5-4

5.3. Defining System Parameters .............................................5-5

5.3.1. The Real Time Clock and Calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8

5.3.2. The Invalid Access Lockout Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

5.3.3. Log Configuration ..............................................5-13

5.3.3.1. The Audit Log and Alarm Log Configuration Options . . . . . . . . . . . 5-13

5.3.3.2. The Temperature Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14

5.3.3.3. Reading, Downloading and Erasing Logs . . . . . . . . . . . . . . . . . . . . 5-14

5.3.4. Callback Security ...............................................5-15

5.3.5. Scripting Options ...............................................5-16

5.3.5.1. Automated Mode .......................................5-18

5.3.6. Power Configuration (RSM-8R8-CM Series Units Only) . . . . . . . . . . . . . . . . . 5-19

5.4. User Accounts .......................................................5-20

5.4.1. Command Access Levels ........................................5-20

5.4.2. Granting Serial Port Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

5.4.3. Granting Plug Access (RSM-8R8 Series Units Only) . . . . . . . . . . . . . . . . . . . 5-22

Table of Contents

5. BasicConfiguration(continued)

5.5. Managing User Accounts ...............................................5-23

5.5.1. Viewing User Accounts ..........................................5-23

5.5.2. Adding User Accounts ..........................................5-23

5.5.3. Modifying User Accounts ........................................5-26

5.5.4. Deleting User Accounts ..........................................5-26

5.6. The Plug Group Directory ..............................................5-27

5.6.1. Viewing Plug Groups ............................................5-28

5.6.2. Adding Plug Groups ............................................5-28

5.6.3. Modifying Plug Groups ..........................................5-29

5.6.4. Deleting Plug Groups ...........................................5-29

5.7. Defining Plug Parameters - (RSM-8R8 Series Units Only) . . . . . . . . . . . . . . . . . . . . . . 5-30

5.7.1. The Boot Priority Parameter (RSM-8R8 Series Units Only) . . . . . . . . . . . . . . 5-32

5.7.1.1. Example 1: Change Plug 3 to Priority 1 . . . . . . . . . . . . . . . . . . . . . 5-32

5.7.1.2. Example 2: Change Plug 4 to Priority 2 . . . . . . . . . . . . . . . . . . . . . 5-33

5.8. Serial Port Configuration ...............................................5-34

5.8.1. RS232 Port Modes ..............................................5-35

5.8.2. The Serial Port Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-36

5.8.3. Copying Parameters to Several Serial Ports (Text Interface Only) . . . . . . . . . 5-43

5.9. Network Configuration .................................................5-44

5.9.1. Network Port Parameters ........................................5-46

5.9.2. Network Parameters ............................................5-47

5.9.2.1. Modem Pooling ........................................5-51

5.9.3. IP Security ....................................................5-52

5.9.3.1. Adding IP Addresses to the Allow and Deny Lists . . . . . . . . . . . . . 5-53

5.9.3.2. Linux Operators and Wild Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-54

5.9.3.3. IP Security Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-54

5.9.4. Static Route ...................................................5-55

5.9.5. Domain Name Server ...........................................5-55

5.9.6. SNMP Access Parameters .......................................5-56

5.9.7. SNMP Trap Parameters ..........................................5-58

5.9.8. LDAP Parameters ..............................................5-59

5.9.8.1. Adding LDAP Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-61

5.9.8.2 Viewing LDAP Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-62

5.9.8.3. Modifying LDAP Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-62

5.9.8.4. Deleting LDAP Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-62

5.9.9. TACACS Parameters ............................................5-63

5.9.10. RADIUS Parameters ............................................5-66

5.9.10.1. Dictionary Support for RADIUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-67

5.9.11. Email Messaging Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-69

5.10. Save User Selected Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-70

5.10.1. Restore Configuration ...........................................5-70

6. RebootOptions..........................................................6-1

6.1. Ping-No-Answer Reboot .................................................6-2

6.1.1. Adding Ping-No-Answer Reboots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

6.1.2. Viewing Ping-No-Answer Reboot Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

6.1.3. Modifying Ping-No-Answer Reboot Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

6.1.4. Deleting Ping-No-Answer Reboot Profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

6.2. Scheduled Reboot .....................................................6-5

6.2.1. Adding Scheduled Reboots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

6.2.2. Viewing Scheduled Reboot Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

6.2.3. Modifying Scheduled Reboots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

6.2.4. Deleting Scheduled Reboots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

Table of Contents

7. AlarmConfiguration......................................................7-1

7.1. The Over Current Alarms (RSM-8R8-CM Series Only) . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

7.1.1. Over Current Alarms - Load Shedding and Auto Recovery . . . . . . . . . . . . . . . 7-4

7.2. The Over Temperature Alarms ............................................7-6

7.2.1. Over Temperature Alarms - Load Shedding and Auto Recovery . . . . . . . . . . . 7-8

7.3. The Lost Communication Alarm ..........................................7-10

7.4. The Ping-No-Answer Alarm .............................................7-12

7.4.1. Ping-No-Answer Notification - TSM and RSM Series Units . . . . . . . . . . . . . . 7-12

7.4.1.1. Defining Ping No Answer IP Addresses -

TSM and RSM Series Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12

7.4.1.2. Configuring the Ping No Answer Alarm -

TSM and RSM Series Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14

7.4.2. Ping-No-Answer Alarm - RSM-8R8 Series Units . . . . . . . . . . . . . . . . . . . . . . . 7-15

7.5. The Serial Port Invalid Access Lockout Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17

7.6 The Power Cycle Alarm ................................................7-19

7.7. Buffer Threshold Alarm .................................................7-20

7.8. The Plug Current Alarm (RSM-8R8-CM Series Only) . . . . . . . . . . . . . . . . . . . . . . . . . 7-22

7.9. The No Dialtone Alarm .................................................7-25

7.10. The Lost Voltage Alarm (Dual Power Inlet Units Only) . . . . . . . . . . . . . . . . . . . . . . . . 7-27

8. TheStatusScreens.......................................................8-1

8.1. Product Status ........................................................8-1

8.2. The Network Status Screen ..............................................8-1

8.3. The Port Status Screen .................................................8-2

8.4. The Port and Plug Status Screens (RSM-8R8 Series Units Only) . . . . . . . . . . . . . . . . . 8-3

8.5. The Plug Group Status Screen (RSM-8R8 Series Units Only) . . . . . . . . . . . . . . . . . . . 8-4

8.6. The Current Metering Status Screen (RSM-8R8-CM Series Only) . . . . . . . . . . . . . . . . 8-5

8.7. The Current History Screen (RSM-8R8-CM Series Only) . . . . . . . . . . . . . . . . . . . . . . . 8-6

8.8. The Power Range Status Screen (RSM-8R8-CM Series Only) . . . . . . . . . . . . . . . . . . . 8-7

8.9. The Power History Screen (RSM-8R8-CM Series Only) . . . . . . . . . . . . . . . . . . . . . . . . 8-8

8.10. The Port Diagnostics Screen .............................................8-9

8.11. Alias Status Screen ....................................................8-9

8.12. The Port Parameters Screens ...........................................8-10

8.13. The Event Logs .......................................................8-11

8.13.1. The Audit Log .................................................8-11

8.13.2. The Alarm Log .................................................8-11

8.13.3. The Temperature Log ...........................................8-11

9. Operation...............................................................9-1

9.1. Connecting and Disconnecting Serial Ports - Text Interface . . . . . . . . . . . . . . . . . . . . . 9-1

9.1.1. Any-to-Any Mode ................................................9-1

9.1.1.1. Connecting Ports - Text Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

9.1.1.2. Disconnecting Ports - Text Interface . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

9.1.1.3. The Port Control Screen - Web Browser Interface . . . . . . . . . . . . . . 9-6

9.1.1.4. Defining Hunt Groups - Text Interface . . . . . . . . . . . . . . . . . . . . . . . . 9-7

9.1.2. Passive Mode ..................................................9-8

9.1.3. Buffer Mode ....................................................9-8

9.1.3.1. Reading Data from Buffer Mode Ports - Text Interface . . . . . . . . . . . 9-8

9.1.3.2. Port Buffers ............................................9-10

9.1.4. Modem Mode .................................................9-11

9.1.5. Modem PPP Mode .............................................9-11

9.2. Controlling Power - Web Browser Interface (RSM-8R8 Series Only) . . . . . . . . . . . . . 9-12

9.2.1. The Plug Control Screen - Web Browser Interface . . . . . . . . . . . . . . . . . . . . . 9-12

9.2.2. The Plug Group Control Screen - Web Browser Interface . . . . . . . . . . . . . . . 9-13

Table of Contents

vii

9. Operation(continued)

9.3. Controlling Power - Text Interface (RSM-8R8 Series Units Only) . . . . . . . . . . . . . . . . 9-14

9.3.1. The Port and Plug Status Screen - Text Interface . . . . . . . . . . . . . . . . . . . . . . 9-14

9.3.2. Switching and Reboot Commands - Text Interface . . . . . . . . . . . . . . . . . . . . 9-15

9.3.2.1. Applying Commands to Several Plugs - Text Interface . . . . . . . . . . 9-17

9.4. The SSH/Telnet Connect Function (Web Browser Interface Only) . . . . . . . . . . . . . . . 9-18

9.4.1. Initiating an SSH Shell Session via the Web Browser Interface . . . . . . . . . . . 9-18

9.4.2. Initiating a Telnet Session via the Web Browser Interface . . . . . . . . . . . . . . . 9-19

9.5. Manual Operation .....................................................9-20

9.6. Logging Out of Command Mode .........................................9-20

10.Telnet&SSHFunctions..................................................10-1

10.1. Network Port Numbers .................................................10-1

10.2. SSH Encryption ......................................................10-1

10.3. The Direct Connect Feature ............................................10-2

10.3.1. Standard Telnet Protocol, SSH and Raw Socket . . . . . . . . . . . . . . . . . . . . . . 10-2

10.3.2. Configuration ..................................................10-2

10.3.3. Connecting to a Serial Port using Direct Connect . . . . . . . . . . . . . . . . . . . . . 10-4

10.3.4. Terminating a Direct Connect Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6

10.4. IP Aliasing ...........................................................10-7

10.5. Creating an Outbound Telnet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-8

10.6. Creating an Outbound SSH Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9

11.SyslogMessages.......................................................11-1

11.1. Configuration ........................................................11-1

12.SNMPTraps............................................................12-1

12.1. Configuration: ........................................................12-1

13.OperationviaSNMP.....................................................13-1

13.1. TSM/RSM SNMP Agent ................................................13-1

13.2. SNMPv3 Authentication and Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1

13.3. Configuration via SNMP ................................................13-2

13.3.1. Viewing Users .................................................13-3

13.3.2. Adding Users ..................................................13-3

13.3.3. Modifying Users ................................................13-3

13.3.4. Deleting Users .................................................13-3

13.4. Plug Control via SNMP (RSM-8R8 Series Units Only) . . . . . . . . . . . . . . . . . . . . . . . . . 13-4

13.4.1. Controlling Plugs ..............................................13-4

13.4.2. Controlling Plug Groups .........................................13-5

13.5. Configuring Serial Ports ................................................13-6

13.6. Viewing Unit Status via SNMP ...........................................13-6

13.6.1. Plug Status (RSM-8R8 Series Units Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-6

13.6.2. Unit Temperature Status .........................................13-6

13.7. Sending Traps via SNMP ...............................................13-7

14SettingUpSSLEncryption................................................14-1

14.1. Creating a Self Signed Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2

14.2. Creating a Signed Certificate ............................................14-3

14.3. Downloading the Server Private Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-4

15.SavingandRestoringConfigurationParameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1

15.1. Sending Parameters to a File ............................................15-1

15.1.1. Downloading & Saving Parameters via Text Interface . . . . . . . . . . . . . . . . . . 15-1

15.1.2. Downloading & Saving Parameters via Web Browser Interface . . . . . . . . . . . 15-2

15.2. Restoring Downloaded Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-2

15.3. Restoring Recently Saved Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-3

Table of Contents

viii

16.UpgradingTSM/RSMFirmware............................................16-1

16.1. Firmware Upgrade Utility (Recommended) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1

16.2. The Upgrade Firmware Function (Alternate Method) . . . . . . . . . . . . . . . . . . . . . . . . . 16-1

17.CommandReferenceGuide...............................................17-1

17.1. Command Conventions ................................................17-1

17.2. Command Summary ..................................................17-2

17.3. Command Set .......................................................17-3

17.3.1. Display Commands .............................................17-3

17.3.2. Control Commands .............................................17-7

17.3.3. Configuration Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-14

Appendices:

A. Specifications.........................................................Apx-1

A.1. Standard TSM Series Units and Standard RSM Series Units . . . . . . . . . . . . . . . . . . Apx-1

A.2. RSM-8R8 Series Units ................................................Apx-2

B. SerialInterfaceDescription..............................................Apx-3

B.1. Serial Port (RS232) ...................................................Apx-3

B.2. TSM and RSM-8R8 Series RJ45 Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-4

B.3. RSM Series DB9M Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-5

C. ConnectingDevicestoRJ45SerialPorts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-6

C.1. Straight RJ-45 Cables and Rollover RJ-45 Cables . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-6

C.2. Connecting DB-9M DTE Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-7

C.3. Connecting DB-25F DTE Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-8

C.4. Connecting DB-25F DCE Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-9

C.5. Connecting RJ-45 DCE Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-10

C.6. DX9F-NULL-RJ Snap Adapter .........................................Apx-10

D. CustomerService.....................................................Apx-11

Table of Contents

List of Figures

2.1. Instrument Front Panel (Model TSM-24 Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2.2. Instrument Back Panel (Model TSM-8 Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

2.3. Instrument Back Panel (Model TSM-24 Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

2.4. Instrument Back Panel (Model TSM-40 Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

2.5. Instrument Back Panel (Model TSM-24-DPE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.6. Instrument Back Panel (Model TSM-40-DPE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.7. Instrument Front Panel (Model RSM-8 Shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

2.8. Instrument Back Panel (Model RSM-8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

2.9. Instrument Back Panel (Model RSM-16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

2.10. RSM-8R8-1 & RSM-8R8-2 - Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

2.11. RSM-8R8-DE Series - Front Panel ............................................2-8

2.12. RSM-8R8-1 - Back Panel ...................................................2-9

2.13. RSM-8R8-2 - Back Panel ...................................................2-9

4.1. Terminal Block Assembly (TSM Series, DC Units Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

4.2. Terminal Block Assembly (RSM Series, DC Units Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

5.1. Boot Priority Example 1 ...................................................5-32

5.2. Boot Priority Example 2 ...................................................5-33

14.1. Web Access Parameters (Text Interface Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1

B.1. TSM Series and RSM-8R8 Series RS232 Port Interface (RJ45) . . . . . . . . . . . . . . . . . . . Apx-3

B.2. RSM Series RS232 Port Interface (DB9) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-3

C.1. Straight Cables ........................................................Apx-6

C.2. Rollover Cables ........................................................Apx-6

C.3. DX9F-DTE-RJ Snap Adapter Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-7

C.4. Connecting DB-9M DTE Devices to an RJ-45 Serial Port on an RSM-8R8 . . . . . . . . . . Apx-7

C.5. DX25M-DTE-RJ Snap Adapter Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-8

C.6. Connecting DB-25F DTE Devices to an RJ-45 Serial Port on an RSM-8R8 . . . . . . . . . . Apx-8

C.7. DX25M-DCE-RJ Snap Adapter Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-9

C.8. Connecting DB-25F DCE Devices to an RJ-45 Serial Port on an RSM-8R8 . . . . . . . . . Apx-9

C.9. Connecting RJ-45 DCE Devices to the RSM-8R8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-10

C.10. DX9F-NULL-RJ Snap Adapter Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Apx-10

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali WTI Telecomando

WTI

WTI RSM-8R4-1 Manuale utente

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione