X10 WM100 Manuale utente
Model WM100
Product Manual
Contents 2 Model WM100
Table of Contents
Section Page
1. Hardware ......................................................................................................................................... 3
2. Software........................................................................................................................................... 4
3. Features ........................................................................................................................................... 5
4. Installation ....................................................................................................................................... 6
5. App – Devices................................................................................................................................... 9
6. App – Rooms .................................................................................................................................. 12
7. App – Scenes..................................................................................................................................14
8. App – Setup.................................................................................................................................... 18
Hardware 3 Model WM100
Hardware
The hardware is simple and flexible. Normally, HUBs require the user to hardwire them
directly into the WiFi router, forcing the user to put the HUB in a location they may not
want it. This unit uses WiFi to connect and communicate with your router, allowing you
to place the X10 HUB anywhere within range of your router.
The hardware does currently have a memory limitation of 32 different addresses.
However, unlike traditional transceivers, this unit can control all of the 256 different
possible codes. In addition, this WiFi Module can also be used to detect what X10
signals are being seen on the electrical line by the WM100. This history can be found in
Setup > X10 WiFi history and settings.
Software 4 Model WM100
Software
oThe Apple App can be found here:
https://itunes.apple.com/us/app/x10-wifi/id1330310265?mt=8
oAndroid App can be found here:
https://play.google.com/store/apps/details?id=com.leconiot.wm100&hl=en
Features 5 Model WM100
Features
•Control up to 32 of all the different possible 256 X10 codes
•Organize all your devices by giving them Names instead of relying on the codes (A1, F3, etc)
•Control all your devices with All ON and ALL OFF functionalities
•Easily create multiple timers per device
•Simple to edit and delete timers as necessary
•Organize your devices into “Rooms” for clearer and easier access
•Control the entire “Room” with the “All Room ON/OFF” buttons
•Create more complex commands with the “Scenes” tab
•Access to On/Off, Dim/Brighten and delays to create scenes tailored for you
•Over the Air firmware updates as necessary
•X10 Command History gives the advanced user the ability to look at the past 50 commands
heard by the WM100, doubling as a great troubleshooting tool
•Simple setup of secondary devices. After the first device is setup, other device setup is a breeze
•Multiple users can control the WM100 simultaneously
•The WM100 has an active ‘sense’ technology that will adjust the status of the devices in the app
regardless of if the signal was sent from the WM100 or any other source (like a hand remote)
Installation 6 Model WM100
Installation
oInstallation – Initial Install
Install the app on your android or apple phone or tablet. The app may need
certain permissions in order to operate correctly (location for timing purposes
as well as camera to allow the app to scan the QR code for installation)
On the back of the WM100 HUB
there is a unique QR code. Locate
the QR code and hit the “SCAN
QR” button in the app to scan it.
To setup the unit for the first time,
open the app on a phone or tablet
that is connected to your home
network.
Select the “setup a new X10 WiFi
HUB”
Installation 7 Model WM100
Simply place
the camera
over the QR
code to read it.
You can now plug in your HUB. The HUB
should be within range of your home’s
router. In general, it should be within 100 ft.
Once plugged in, you are now ready to
connect the HUB to your home’s network.
To get the HUB into install mode, simply
press and HOLD the “SYNC” button in the
upper right of the HUB for about 5 seconds
(until the LED begins to blink steadily), then,
let go of the SYNC button.
While the LED is blinking on the WM100, go
back to the App and press the “CONNECT”
button.
The app will automatically populate the
network with the network your phone or
tablet is connected to. If you discover at this
point you are not connected to your
network, close the app, connect to your
network and restart installation.
Enter your WiFi password and then hit
“NEXT” to enable your X10 HUB to
communicate on your home network.
Installation 8 Model WM100
oInstallation – On other devices after initial install
Once the HUB is installed on one device successfully, it is easy to add additional
phones and tablets. Load the app on the new device and select “Connect to an
existing Hub”. Scan the QR Code when prompted and quickly plug the WM100
into the outlet. The App will connect and download the settings and
preinstalled devices from the WM100.
After your X10 HUB has
connected to your home’s
network, you will end up on
the “Success” screen. If
unsuccessful, a message will
pop-up and prompt you to
try again.
At this point, you can start
adding X10 Devices or simply
exit the setup.
App - Devices 9 Model WM100
App – Devices
oAdd Device
To add a device, go to the Devices tab and select the “Add
Device” button in the lower left.
On the Add Device page, you can
give the device a name, set the
house and unit code (it should
match the X10 device you are
trying to control) and indicate if it
is a dimmable module or not (like
the LM465 or WS467).
It is important to indicate if it is a
plugin module or wall switch as
they have different dimming
parameters.
Press Save when done (upper right)
App - Devices 10 Model WM100
oDevice Configuration
Once the Device is created, you can now edit it as necessary by pressing
the gear icon to the right of the device.
Adding a Timer
•To add a timer, hit the “Add Timer”button in the lower left of the Edit
Device Screen (as seen above)
You will now see a few new options that
were not there when you were creating
the device.
Trash Device – this will simply delete this
device.
Add Timer – This will allow you to add a
timer and indicate which days of the
week you would like it to control the
device ON, OFF or DIM.
Dawn | Dusk – This allows you to create
ON or OFF commands according to your
local dawn or dusk times (this does
require giving the app permission to
know your location.
Indice
Altri manuali X10 Interruttore
