Xerox CiPress 325 Manuale utente
Xerox®CiPress™325 / 500 Production
Inkjet System
Web Threading Guide
5.0 Software
August 2012
©2012 Xerox Corporation. All rights reserved. XEROX®, XEROX® and Design and CiPress™
are trademarks of Xerox Corporation in the United States and / or other countries.
Document Version 1.0 (May 11, 2012).
BR3164
Table of Contents
1 Copyright Statement....................................................................................ii
1 Overview........................................................................................................1-1
2 Preparing the Infeed Module for Threading..................................2-1
3 Threading the Web Registration Module........................................3-1
4 Threading the Web Cleaner and Around the Web Heating
Drum..............................................................................................................4-1
5 Threading the Right and Left Marking Towers..............................5-1
6 Threading Around the Web Cooling Drum.....................................6-1
7 Threading the Outfeed Module...........................................................7-1
8 Web Registration Procedures................................................................8-1
9 Setting Up and Activating the Web Registration
Module.........................................................................................................9-1
10 Web Registration Module Overview..............................................10-1
i
Xerox®CiPress™325 / 500 Production Inkjet System
Web Threading Guide
Xerox®CiPress™325 / 500 Production Inkjet System
ii
Web Threading Guide
Table of Contents
1
Overview
Attention
This guide is intended to be followed in a linear fashion from the first chapter to the last
chapter.
The first section of this guide details a web threading process in six steps, which starts
at the right side of the CiPress™(the Infeed Module) and ends at the left side of the
CiPress™(the Outfeed Module).
1. Preparing the Infeed Module for Threading
2. Threading the Web Registration Module
3. Threading the Web Cleaner and Around the Web Heating Drum
4. Threading the Right and Left Marking Towers
5. Threading Around the Web Cooling Drum
6. Threading the Outfeed Module
The second part of this guide details setting up the web that was just threaded.
1. Web Registration Procedures
2. Setting Up and Activating the Web Registration Module
The last chapter of this guide is for reference purposes to help identify the functions
and components of the Web Registration Module.
1-1
Xerox®CiPress™325 / 500 Production Inkjet System
Web Threading Guide
Xerox®CiPress™325 / 500 Production Inkjet System
1-2
Web Threading Guide
Overview
2
Preparing the Infeed
Module for Threading
This section describes the web threading process for the highlighted section of the web
path.
1. Prepare the unwinder and any other external devices at the start of the Infeed Module.
Correctly align the physical position of the unwinder, turnbars, and finishing equipment
with the CiPress™. The unwinder should be powered on in the ready state, able to
feed paper as it is pulled through the web path.
2. Open the Infeed Module Front Door.
Note
The Primary CiPress™is also known as the Upstream CiPress™in a Tandem or Duplex
configuration. When mentioned, The Secondary
2-1
Xerox®CiPress™325 / 500 Production Inkjet System
Web Threading Guide
CiPress™is also known as the Downstream CiPress™in a Tandem or Duplex
configuration.
3. Start with the edge of the web at the unwinder and cut a 45 degree angle across two
thirds of the sheet, leaving a straight edge about 76 mm (3 inches).
4. Provide paper slack by manually pulling the web about 3 to 5 meters (5 to 10 feet)
off of the unwinder. You need to perform this step throughout the web threading
process.
5. Place the web against the Web Positioning Label.
Xerox®CiPress™325 / 500 Production Inkjet System
2-2
Web Threading Guide
Preparing the Infeed Module for Threading
6. Open the Infeed Module end cover located at the right side of the Infeed Module to
access the Web Edge Guide.
7. To identify which metal tab to use on the Web Edge Guide for aligning and inserting
the web, refer to the label, also located on the Infeed Module, and perform the
following steps.
Start web alignment here
1
Primary CiPress™
2
Rear metal tabs
3
Secondary CiPress™
4
Front metal tabs
5
a) Begin at the right side of the guide and align the web edge at either the pinfeed
or pinless paper icon. To determine the correct metal tab to use for aligning the
2-3
Xerox®CiPress™325 / 500 Production Inkjet System
Web Threading Guide
Preparing the Infeed Module for Threading
web on the guide, refer to the appropriate CiPress™icon on either lower corner of
the label.
Left front metal tab (gold color from label) used to align the web for the
Secondary CiPress™.
1
Right front metal tab (blue color from label) used to align the web for the
Secondary CiPress™.
2
b) If the left edge of the web ends at the blue area on the label, use the metal tab
that corresponds with the blue arrow. If the web edge ends at the gold area, use
the metal tab that corresponds with the gold arrow.
8. Ensure that the Front and Rear Web Edge Guides are located against their respective
sides of the Infeed Module.
a) Loosen the thumb screw.
b) Move the Web Guide to the appropriate position.
c) Tighten the thumb screw.
Front Web Guide Thumb Screw
1
Front Web Guide
2
9. Adjust the orientation of the Web Tension Adjuster by pulling up the pin and rotating
the Adjuster depending on the weight of the media being used.
Xerox®CiPress™325 / 500 Production Inkjet System
2-4
Web Threading Guide
Preparing the Infeed Module for Threading
Altri manuali per CiPress 325
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Xerox Stampante
Xerox
Xerox Nuvera 100 Manuale utente
Xerox
Xerox Phaser 860 Manuale utente
Xerox
Xerox Phaser 860 Manuale utente
Xerox
Xerox DocuColor 7000AP Manuale di istruzioni
Xerox
Xerox Phaser 4 400 Manuale utente
Xerox
Xerox Phaser 6120 Manuale utente
Xerox
Xerox DocuPrint N2125 Manuale utente
Xerox
Xerox DocuPrint 203A Manuale utente
Xerox
Xerox Phaser 6200 Manuale utente
Xerox
Xerox DocuMate 3120 Manuale utente
Xerox
Xerox 4050 Manuale
Xerox
Xerox Diablo 1620 Manuale utente
Xerox
Xerox PHASER 6250 Manuale operativo
Xerox
Xerox PHASER 7500 Manuale operativo
Xerox
Xerox 8860MFP - Phaser Color Solid Ink Manuale utente
Xerox
Xerox Phaser 4600DN Manuale operativo
Xerox
Xerox Legacy 4110 Istruzioni per il montaggio
Xerox
Xerox 8200B - Phaser Color Solid Ink Printer Manuale utente
Xerox
Xerox Nuvera 100 Istruzioni per il montaggio
Xerox
Xerox Phaser 2135 Manuale utente
