Xtreme NXRT-EBP Guida
NXRT-EBP
External Baery Packs
User & Installaon Manual
www.xpcc.com | © 2015 Xtreme Power Conversion Corporaon. All rights reserved. (Rev 5/20/15)
Xtreme Power Conversion Corporaon
NXRT-EBP User’s Manual
Page 2
External Baery Packs
Extended Baery Pack User Guide
Esmated Run Time for UPS with Extended Baery Packs
MODEL
LOAD RUNTIME FOR QTY OF EXTENDED BATTERY PACKS
IN MIN.
VA WATTS UPS (1) EBP (2) EBP
NXRT-1000
500 350 23 91 176
1000 700 10 41 80
NXRT-1500
750 525 18 68 124
1500 1050 9 32 60
NXRT-2000
1000 700 29 109 200
2000 1400 14 52 97
NXRT-3000
1500 1050 18 67 123
3000 2100 9 32 60
*For applicaons requirements of more than two EBP’s, a CBP must be added. See Appendix B for addional
informaon.
CAUTION: It is very crical to connect the correct voltage EBP with the UPS intended.
EBP1 is for NXRT-1000
EBP2 is for NXRT-1500
EBP3 is for NXRT-2000/3000
CONNECTING THE INCORRECT BATTERY PACK TO THE UPS MAY RESULT IN DAMAGE TO THE UPS
AND/OR BATTERY PACK WILL VOID THE WARRANTY.
All EBP’s have a dierent DC voltage conguraon intended only for the UPS’s listed above.
PLEASE DO NOT MIX EBP’s AND MAKE SURE YOU ONLY CONNECT THE EBP TO LIKE EBP’s OR UPS
INDICATED ABOVE. DC VOLTAGES ARE MARKED ON BOTH THE UPS AND THE EBP – MAKE SURE
THEY MATCH.
Cauon label on EBP cable connectors - PLEASE CHECK VOLTAGES CAREFULLY
Xtreme Power Conversion Corporaon
NXRT-EBP User’s Manual
Page 3
External Baery Packs
Extended Baery Pack Conguraon
EBP1 for NXRT-1000
EBP2 for NXRT-1500
EBP3 for NXRT-2000/3000
Xtreme Power Conversion Corporaon
NXRT-EBP User’s Manual
Page 4
External Baery Packs
NXRT-EBP front panel
LED Descripon
The Baery Test LED GREEN indicates that the DC output of the Extended Baery Pack (EBP) is normal.
To perform the Baery Test:
• Switch the breaker on the rear of the EBP to ON posion
• Press the Baery Test Buon on the front panel of the EBP
• The DC output from the EBP is normal when the Baery Test LED is illuminated
Prior to connecng EBP’s, test each EBP to assure proper operaon.
Extended Baery Pack Operaon
The NXRT UPS System can be connected with up to two EBPs to increase the runme when connected to the UPS
supporng the load.
1. The DC Circuit Breaker on the rear of the EBP connects and disconnects the DC bus voltage from the EBP
to the UPS. The DC Circuit Breaker will also trip to the OFF posion in the event of an over-current condi-
on in the EBP.
EBP2 rear view
2. The EBP’s use a cable shipped with each EBP to “daisy chain” together addional EBP’s to the rst EBP be-
ing connected to the UPS in the appropriately labeled connector, or for connecng the rst EBP to the UPS.
Xtreme Power Conversion Corporaon
NXRT-EBP User’s Manual
Page 5
External Baery Packs
EBP’s “daisy chain” to UPS or other EBP
Extended Baery Pack Installaon
CAUTION: Extended Baery Pack (EBP) Installaon should be performed by qualied service personnel.
1. Verify that the DC circuit breaker on the rear panel of the EBP is in the OFF posion.
2. Turn the UPS OFF and disconnect the UPS Input Cord from the AC wall outlet.
3. Remove the EBP connector cover from the UPS rear panel.
4. Connect the external DC baery cable from the EBP to the appropriate connector on the UPS.
5. Secure the DC baery cable to both the rear of the UPS and the rear of the EBP by using M3 x 8 screws
provided (2 each per connector end).
6. Repeat the above procedure for tesng and securing each addional EBP required.
7. Move the DC circuit breaker on the rear of each EBP to the ON posion. At this point the UPS will need to
be started.
NOTE: If the EBP is going to be out of service or stored for six months or longer, the baeries must be re-
charged for at least 36 hours every six months.
Indice
Altri manuali Xtreme Pacco batterie
