Yamaha Disklavier E3 Manuale tecnico
Update Manual
Introduction ......................................................................................................................................... 2
Updating the Disklavier ...................................................................................................................... 3
Video Synchronized Recording........................................................................................................... 5
Video Synchronized Playback ............................................................................................................ 9
Setting the Disklavier for Audio Data Reception/Transmission ................................................... 10
Converting MIDI Data to a Standard Form (Strip XP)..................................................................... 11
Switching the Languages for the Screen ........................................................................................ 13
Table of Contents
2
Version 2.10 offers an expansion of the features available in the Disklavier E3
and increases the performance reliability of the Disklavier E3. The followings
are the new features in version 2.10:
• Video synchronized recording and playback features (Pages 5 – 9)
• Flexible audio input (OMNI IN) and output (OMNI OUT) setting (Page 10)
• “Strip XP” features (Page 11)
• Switchable language setting for the screen (Page 13)
First, update your Disklavier following the procedures on page 3.
Introduction
3
Important:
Be sure NOT to turn off the Disklavier
during the update.
First you need to update the Disklavier firmware using update program
(downloaded and saved from the website onto a USB flash memory, or
downloaded directly to the Disklavier via Internet).
Note:
For this operation you have to
download update program via Internet
in advance, and shut down the
Disklavier.
Note:
Be sure to make backups of the song
before updating.
Make sure that Disklavier is shut down.
Holding [PLAY/PAUSE] on the control unit, press [ON/OFF].
The current version information of each module appears one after the
other.
Make sure that the update program is prepared, then press
[ENTER].
The starting screen appears.
Press [ENTER] again.
After a while, the update confirmation message of each module
appears.
Updating the Disklavier
Shut down the Disklavier [PLAY/PAUSE] and [ON/OFF]
1
2
Hold
+
CTRL system V1.10
(ENT)*UPDATE
3
4
V1.10
(PLAY,STOP)CTRL-SURE?
V2.10
Continued to next page
4
Press [PLAY/PAUSE] to update, [STOP] to skip to the next
module.
When the update of the selected module completes, the update
confirmation message of the next module appears. Repeat steps 4
and 5.
The closing screen appears when the update for all modules
completes.
Restart the Disklavier.
5
V1.10
DO NOT REMOVE DISK! 3500
V2.10
6
5
For details on video synchronized
playback, see “Video Synchronized
Playback” on page 9.
By recording a song played on the Disklavier synchronized with the video
recording, later on, you can enjoy piano playback with the video. First set up
the camcorder, the DVD recorder, and the Disklavier, and then start recording
by following the procedures below.
■Setting for Video Synchronized Recording
Press [SETUP] on the remote control.
The setup menu screen appears.
Select “AudioI/O” with the cursor buttons ([ ] [ ] [ ]
[ ]), then press [ENTER].
The audio I/O setting screen appears.
Select “OMNI IN” with the cursor buttons ([ ] [ ]), then
press [+/YES] and [–/NO] to change setting to “AutoDetect”.
Video Synchronized Recording
Connect a camcorder and a DVD recorder[SETUP] “AudioI/O”
1
{
2
{
]
3
]
Continued to next page
6
Select “OMNI OUT” with the cursor buttons ([ ] [ ]), then
press [+/YES] and [–/NO] to change setting to “SYNC”.
Press [ENTER] to complete the operation.
Note:
Confirm the shape of input/output
connectors on the camcorder and the
DVD recorder, and prepare the cables
fit to them.
Connect a camcorder and a DVD recorder to the control unit.
4
]
[
5
6
TV
(for displaying)
RCA cord
(not supplied)
Control unit
RCA cord
(not supplied)
To
audio
output
To video
input
To
audio
input
To A/V
output
To video
input
To
video
output
DVD recorder
(for recording and playback)
Video
connector
(yellow)
Video cord
(not supplied)
A/V cord
(supplied with the
camcorder)
Camcorder
(for shooting)
Continued to next page
7
■Starting Video Synchronized Recording
To select a medium and album, see
Chapter 3 “Basic Song Playback –
Selecting Medium and Their Contents”
on operation manual.
Select a destination medium and album.
Press [RECORD].
The video synchronized recording standby screen appears, and
[RECORD] on the control unit lights red, and [PLAY/PAUSE] flashed in
green.
Set the camcorder to video shooting mode.
Select the video input on the DVD recorder which the
camcorder is connected to, then start recording on the DVD
recorder.
Press [PLAY].
[PLAY/PAUSE] stops flashing, and the counter starts to advance.
Note:
This step is necessary for
synchronization of the song and the
video playback, and should not be
omitted.
Wait for approximately ten seconds, and then start playing
your song.
Press [STOP] when you finish playing your song.
Stop recording on the DVD recorder.
1
2
(New Song)
=Record=(SYNC) SO
<00:00>
LR 99%
A01-005
3
4
5
(New Song)
=Record=(SYNC) SO
<00:00>
LR 99%
A01-005
6
7
8
Continued to next page
8
■Using the Camcorder only
If your camcorder has both mic input and audio output, you can
perform video synchronized recording using the camcorder only.
1. Set the Disklavier following the procedures 1 to 5 on page 5.
2. Connect a camcorder to the control unit.
3. Select a destination medium and album.
4. Press [RECORD].
5. Start recording on the camcorder.
6. Press [PLAY].
7. Wait for approximately ten seconds, and then start playing your
song.
8. Press [STOP] when you finish playing your song.
9. Stop recording on the camcorder.
Camcorder
RCA cord with
resistance
(not supplied)
To mic/line
input
To audio
output
Control unit
RCA cord
(not supplied)
9
For details on video synchronized
recording, see “Video Synchronized
Recording” on page 5.
You can enjoy piano playback with the video recorded on the DVD recorder.
Perform the video synchronized recording in advance.
Note:
Be sure to rewind the video cassette to
locate the beginning of the recording.
It may take some time before piano
playback starts if you start playback
halfway through the video.
Make sure that the OMNI IN setting is set to “AutoDetect”.
Note:
When using the song copied to the
USB flash memory, it may take some
time until the Disklavier recognizes the
information for synchronization.
Turn down the volume completely on the TV if you connect
the audio output of the DVD recorder to the TV.
See “Setting for Video Synchronized
Recording” on page 5.
Turn down the volume completely on the camcorder if you use the
camcorder only.
If the piano playing is not
synchronized with the video picture,
adjust the offset time for
synchronization. See “Setting the
Disklavier for Audio Data Reception/
Transmission” on page 10.
Start playback on the DVD recorder.
Start playback on the camcorder if you use the camcorder only.
The Disklavier automatically searches and selects the song paired
with the video, and then starts playback as well.
If noises (synchronized signal) are
heard during video synchronized
playback, turn down the signal level
and re-record. See “Setting the
Disklavier for Audio Data Reception/
Transmission” on page 10.
Note:
You cannot operate the Disklavier
using the control unit or remote control
during video synchronized playback. If
you want to stop playback of the song,
stop playback on the DVD recorder (or
the camcorder).
Video Synchronized Playback
1
2
3
4
PIANO005.MID
10
You can select the kind of the incoming/going out audio signals. The following
options are available in version 2.10.
OMNI IN
Auto Detect: Select this when you make the Disklavier detect the input signal
automatically.
OMNI OUT
SYNC: Select this when you output the SMPTE signal used for video
synchronization playback.
SYNC IN Offset
Adjusts the length of the offset time that leads the actual playback of entire
recording. The offset time can be set in a range of –500ms to +500ms.
Decrease this value to delay the piano playing, and increase to advance the
piano playing.
SYNC OUT Level
Adjusts the output level of the SMPTE signal. For normal use, the adjustment
of this option is not required. If noises (synchronized signal) are output from
the OUTPUT jacks during video synchronized playback, turn down the level
and re-record.
Setting the Disklavier for Audio Data Reception/Transmission
(Additional Features)
[SETUP] “AudioI/O”
Altri manuali per Disklavier E3
8
Indice
Altri manuali Yamaha Strumento musicale
Yamaha
Yamaha CP33 Sibelius 5 Manuale utente
Yamaha
Yamaha P-35 Manuale utente
Yamaha
Yamaha Clavinova CLP-134 Manuale utente
Yamaha
Yamaha Clavinova CVP-709 Manuale utente
Yamaha
Yamaha YC-25D Manuale utente
Yamaha
Yamaha Alto Venova YVS-120 Manuale utente
Yamaha
Yamaha Clavinova CVP-83S Manuale utente
Yamaha
Yamaha 142 Manuale utente
Yamaha
Yamaha AES620 Manuale utente
Yamaha
Yamaha Clavinova CVP-55 Manuale utente
Yamaha
Yamaha Electone MC-600 Manuale utente
Yamaha
Yamaha Clavinova CLP-115 Manuale utente
Yamaha
Yamaha Clavinova CLP-760 Manuale utente
Yamaha
Yamaha SILENT Piano SD Series Manuale utente
Yamaha
Yamaha YDP-101 Manuale utente
Yamaha
Yamaha Clavinova CVP-10 Manuale utente
Yamaha
Yamaha Venova YVS-100 Manuale utente
Yamaha
Yamaha DG-1590A Manuale utente
Yamaha
Yamaha Wooden Recorder Manuale utente
Yamaha
Yamaha YVD20 Manuale utente
