Yeelight YLXD01YL Manuale utente
Yeelight Smart LED Ceiling Light
Frontal projection of ttings
(basis) of the lamp
Backside the lamp base
switching device, connecting
detail
blocking switch
Basis
Opening for fastening of a
cartridge
Fixing opening for the self-
cut screw
Opening for
threading of a cord
Expansion
bolt shield
x 2
Screw self-tapping
screw x 2
Metric screw Remote control (not
basic equipment)
Installation direction
1. Open packaging, get the ceiling lamp, shift inside the blocking switch, remove a support.
Attention! In order to avoid defeat by an electric current before installation it is necessary
to disconnect power supply, to set step by step accurately according to the instruction. The
wrong installation can lead to falling, the re, defeat by current and to other accidents.
2. Fixing of the basis
Way a: to pass a cord of food through an opening for a cord, using the self-cut screw to x
the basis on a ceiling, to be convinced that the basis is reliably xed. (The recommended
way).
Way b: Check integrity of two knots of fastening of a connecting box of the lamp, after check
to stretch a cord through an opening for a cord, using metric screws to x the basis with a
connecting box on a ceiling, to be convinced that the basis is reliably xed.
3. Connection of a cord of food.
According to requirements of the following scheme, it is necessary to remove isolation
from a wire on 8-9 mm.
Insert a cord of food into an opening of a
terminal block (before pulling out a cord,
it is necessary to press the red button on
a terminal block, and after that to pull out
him).
Connect a cord of food, as shown in the
picture, to check reliability of connection.
4. With both hands take the lamp from two parties, without pressing a luminous surface,
to direct to the basis, to slightly push both parties of the lamp into the basis, after click
installation of the lamp is complete. Before unclenching hands, it is necessary to be
convinced that latches on both sides of the lamp completely became on places.
Remote control
(The remote control isn’t included in a basic equipment, it needs to be purchased
separately)
For this purpose, to adjust connection of the panel with the ceiling Yeelight LED lamp for
use them in one room, it is necessary to turn on the ceiling lamp, within 60 seconds, at
the same time press the OFF+M keys on the remote control and at once to release. The
blinking indicator lamp on the panel means that there is a connection installation. Wait until
the lamp starts blinking, it means that installation of connection is complete.
Description of functions
To turn on
the light
To turn o
the light
Control of color
temperature
Night lamp
Intellectual management
1. Scan a QR code or load the Yeelight mobile application;
2. The ceiling lamp has to be in the included state, perform operations being guided by
application operation manuals.
Make sure that there is an access to WI-FI network and continuous connection to the
Internet.
These goods are compatible to the intellectual Mijia platform, it can be managed through
the Mijia application, support the MIUI system, can have access and to be interconnected
also with other products of the intellectual Mijia platform.
Restoration of factory settings
Using the food switch, to continuously switch on and o light of 5 times (to switch on and
o every time for 2 seconds), in 5 seconds the lamp will automatically reboot and factory
settings will be restored.
* if the ceiling lamp is used in the new network environment, it is necessary to restore
factory settings, and after that anew to adjust network connection.
Parameters
Product model: YLXD01YL;
Range of color temperature: 2700K - 6500K;
Working temperature:-10 - +40 °C;
Range of working humidity: 0% - 85% of RH;
Useful life: about 25000 hours;
Power factor: 0.9;
Rated power: 28 W;
Rated power consumption: 220V - 50/60 Hz 0.127 A;
Supports: Android 4.4 & iOs 8.0 and subsequent versions;
Wireless connection: WI-FI IEEE of 802.11 b/g/n 2.4 GHz, Bluetooth 4.2 BLE.
Features of a product
Adjustment of color
temperature
Brightness
control
Night lamp -
moonlight
Color rendition
coecient
Protection against
dust
Intellectual location Management via
the mobile phone
Software update
Special indications for safety measures
1. Before use be convinced that voltage corresponds to the working tension of this
product; use of improper tension can lead to damage of a product or potentially dangerous
situation;
2. it is impossible to change LED modules, it is impossible to sort a product independently;
3. in operating time the lamp can make heat, it is necessary to support convection of air for
a thermolysis.
Hazardous substances
This table is made on the basis of regulations of SJ/T 11364
О: designation means that the content of harmful substance in this detail below the
restrictions specied in regulations of GB/T 26572
Х: designation means that the content of harmful substance in this detail exceeds the
restrictions specied in regulations of GB/T 26572
XIAOMI-MI.COM
Altri manuali Yeelight Lanterna
