Yoshimura 070BG123100 Manuale utente
RESEARCH&DEVELOPMENT OF AMERICA, INC.
www.yoshimura-rd.com
FENDER ELIMINATOR KIT
070BG123100
Honda CB300R
5420 DANIELS STREET STE A, CHINO CA., 91710 · (800) 634-9166 · (909) 628-4722 · FAX (909) 591-2198
THIS PRODUCT IS NOT DOT APPROVED.
Yoshimura R&D of America, Inc. is not liable or responsible for any resulting event caused by the
installation of this product. Check with local laws and regulations for compliance prior to
installation and use. This product is not intended for use on public highways.
! !
No.
Item
Description
Qty.
1
12310-FEBKT
Fender Eliminator Bracket
1
2
12200-FEBKT
License Plate Bracket
1
3
070BG-LPF
License Plate Frame
1
4
070BG-LH-K1
Fender Eliminator LED Light
1
5
12310-TSBKT-L
Left Turn Signal Bracket
1
6
12310-TSBKT-R
Right Turn Signal Bracket
1
7
M4X6BHS
4mm x 6mm Button Head Screw
2
8
M6X10BHS
6mm x 10mm Button Head Screw
2
9
M6X14BHS
6mm x 14mm Button Head Screw
2
10
M6X16BHS
6mm x 16mm Button Head Screw
4
11
6MMWASHER
6mm Washer
6
12
12310-FEBKT-SPR
Fender Eliminator Bracket Spacer
2
13
6MMLN
6mm Nylon Lock Nut
4
**
BN-SSS-22-18
Solder Shrink Connectors
2
**
ZT-200
Cable Tie
1
**
17100
Yoshimura Sticker Sheet
1
Optional Accessories
073BG-HON-1
Turn Signal Wire Adapters
072BGLTSR
Yoshimura LED Turn Signal Kit w/ Relay
072BGLTSR-S
Yoshimura Sequential LED Turn Signal Kit w/ Relay
070BGUNVTBKT
Yoshimura Turn Signal Bracket Kit, Standard
070BG12121TSBKT
Yoshimura Turn Signal Bracket Kit, Corner
2
Assembly Diagram
** Not shown on diagram.
1
2
3
4
5
6
7
8
9
10
10
11
11
12
13
1. Remove passenger seat.
2. Locate and disconnect license plate light and
turn signal connectors.
3. While securely supporting the stock fender
assembly, remove the four bolts securing
the fender assembly to subframe and carefully
remove fender assembly making sure not to
damage connectors in the process.
4. Disassemble the stock fender assembly and
remove the stock turn signals.
5. Cut the stock license plate light wires from
the stock fender assembly. Be sure to cut at
least a 6” section of wire from the connector.
Removal
Installation
3. Install (No. 2) 12200-FEBKT, license plate
bracket to (No. 1) 12310-FEBKT, fender
eliminator bracket using (No. 8) M6X10BHS,
6mm button head screws.
4. Install stock left and right turn signals onto
(No. 5,6) 12310-TSBKT-L/R, left and right turn
signal brackets.
5. Assemble and install (No. 3) 070BG-LPF,
license plate frame and (No. 6) 12310-TSBKT-
L/R, left and right turn signal bracket to (No. 2)
12200-FEBKT, license plate bracket using
(No. 9,10) M6X14BHS and M6X16BHS, 6mm
button head screws and (No. 11,13)
6MMWASHER, 6mm washer and 6MMLN,
6mm lock nut.
6. Using the BN-SSS-22-18, solder shrink
connectors provided in the kit, connect the
Yoshimura license plate light wires to the stock
license plate light wires as follows:
Black Wire -to- Green (-)
Red Wire -to- (+) Brown
a) Strip the stock fender light wire ends
1/4” - 1/2” and insert into BN-SSS-22-18,
solder connectors provided in the kit.
b) Center the spliced wire ends in the
middle and using a heatgun or lighter,
apply heat evenly on the outer edges of
the connector to shrink and hold wires in
place.
3
1. Install (No. 1) 12310-FEBKT, fender eliminator
bracket to subframe using (No. 10,11,12)
M6X16BHS, 6mm button head screw,
6MWASHER, 6mm washer, and 12310-FEBKT-
SPR, fender eliminator bracket spacer as
shown.
Note: 12310-FEBKT-SPR mounts between
fender eliminator bracket and the plastic
undertail.
2. Install (No. 4) 070BG-LH-K1, fender eliminator
light onto (No. 2) 12200-FEBKT, license plate
bracket using (No. 7) M4X6BHS, 4mm screws.
4
27
8
3
9
5
10
11
6
13
1
11
10
12
1
2
c) Making sure that the stripped ends are
centered, heat the center of the connector
evenly until the solder begins to liquify.
d) Allow to cool completely and tug both
ends of the wires to verify that connection
is secured.
Scan for link to solder shrink connector
instruction video.
7. Route license plate light wire and turn signal
wires along the left side of (No. 1) 12310-
FEBKT, fender eliminator bracket and through
undertail. Re-connect license plate light and turn
signal connectors.
Note: Using the cable tie supplied in the kit,
secure wires along left side of fender
eliminator bracket.
8. Re-install passenger seat.
9. Check for proper function of license plate light
and that all brackets and components are
secure prior to riding.
4
Altri manuali Yoshimura Accessori per motociclette
Yoshimura
Yoshimura 570-400-0300 Manuale utente
Yoshimura
Yoshimura Enduro Series Manuale utente
Yoshimura
Yoshimura Signature Series Manuale utente
Yoshimura
Yoshimura Signature Series Manuale utente
Yoshimura
Yoshimura RACE Series Manuale utente
Yoshimura
Yoshimura 231032D320 Manuale utente
Yoshimura
Yoshimura 133200J220 Manuale utente
Yoshimura
Yoshimura 070BG141503 Manuale utente
Yoshimura
Yoshimura 12130A5500 Manuale utente
Yoshimura
Yoshimura 070BG133001 Manuale utente
Yoshimura
Yoshimura Enduro Series Manuale utente
Yoshimura
Yoshimura RACE 11621C0520 Manuale utente
Yoshimura
Yoshimura 225850S321 Manuale utente
Yoshimura
Yoshimura RACE131414M220 Manuale utente
Yoshimura
Yoshimura 070BG131001 Manuale utente
Yoshimura
Yoshimura RACE Series Manuale utente
Yoshimura
Yoshimura 070BG149500 Manuale utente
Yoshimura
Yoshimura Street 216600C250 Manuale utente
Yoshimura
Yoshimura 225851S721 Manuale utente
Yoshimura
Yoshimura RACE SERIES Manuale utente
