ZBA ZB-8150 Manuale utente
ZB-8150/ZB-8110/ZB-8210
CCD BARCODE SCANNER
User’s Manual
ZBA Inc
94 Old Camplain Road
Hillsborough NJ 08844
Phone: 908-359-2070
Fax: 908-359-1272
Web: http://www.zbausa.com/
1
Installation:
Keyboard Wedge
1) Turn off the PC
2) Disconnect the keyboard cable from the PC.
3) Connect the Keyboard Cable to the scanner and connect the scanner cable to the PC
4) Turn the terminal/computer power on.
5) You are ready use the scanner
RS-232
1) Turn off the PC.
2) Connect the Scanner cable to the PC.
3) Plug the power supply to the scanner
4) Plug the power pack into power source.
5) Turn on PC, You are ready to use the scanner
USB (with HID Keyboard Interface)
1) Plug the USB cable to PC. (some USB hub may have power problem, Check with HUB manufacturer)
2) Follow the instruction to install windows driver come with your windows operating system.
Note: The scanner may not work with windows 95 or windows 98 first edition.
2
Default Setting for each barcode shown
as below:
Read
Enable
Code Type
8110 8150/8210
Checksum
V
erification
Enable
Checksum
Transmission
Enable
Code
ID
UPC-A V V VVA
UPC-E V V VVE
EAN-13 V V VVF
EAN-8 V V VVFF
Code-39 V V ＊
Interleaved
2 of 5 V V Vi
Industrial
2 of 5 - - i
Matrix 2 of 5 B
Codabar V%
Code-128 V V V#
Code-93 V&
Code-11 VOne digit O
MSI/Plessey V@
UK/Plessey V@
Telepen S
Standard 2 of 5 - - i
RSS-14 R4
RSS-Limited RL
RSS-Expanded RX
China Post t
Italian
Pharmaode. p
Code-16K - -
PDF417 V(8210) - -
3
ZBA ZB- 8110 / 8150 - 1D Barcode scanner
Specification Model8110 Model8150
Operational
Light Source 660 nm Visible Red LED
Optical System 2048 pixel CCD
(Charge-coupled device)
Depth of Scan Field 0-80 mm
(CODE 39,
PCS=90%, 20mils)
0-250 mm
(CODE 39,
PCS=90%, 20mils)
Scanning Width 80 mm 120 mm
Scan Speed 50 scans/sec 200 scans/sec
Resolution 0.125mm(5mils)
Code39,PCS=45%,
on contact
0.1mm(4mils)
Code39,PCS=90%,
Print Contrast 30% or more
Scanning Angle Front: 60° Rear: 60° Yaw: 75°
Decode Capability Autodiscriminates all standard
barcodes; Other symbologies can be
ordered optionally
Beeper Operation 7 tones or no beep
Indicator Green led
Mechanical
Length 182 mm
Width-handle 26 mm
Width-head 90 mm 74 mm
Depth-handle 51 mm
Depth-head 35 mm
4
Weight 155 g (cable not
included)
160 g (cable not
included)
Cable – K/B wedge Straight 2.0 m
Cable – universal
type Straight 2.3 m
Connector type RJ-45 phone jack connector
Case material ABS plastic
Cushion material Rubber
Electrical
Input Voltage 5 VDC ± 0.25V
Power - Operating 380 mW 1275 mW
Power - Standby 240 mW 600 mW
Current - Operating 76 mA @ 5 VDC 255 mA @ 5 VDC
Current - Standby 48 mA @ 5 VDC 120 mA @ 5 VDC
DC Transformers Class 2; 5VDC @ 450 mA
Agency listing UL, FCC Class A
Environmental
Operating
Temperature 0℃to 45℃(32℉to 113℉)
Storage -40℃to 60℃
(-40℉to 140℉)
Humidity 5% to 90% relative humidity,
non-condensing
Light Level Up to 15000 Lux Up to 60000 Lux
Shock 1.0m drop onto
concrete
1.5m drop onto
concrete
Contaminants Seals to resist airborne particulate
contaminants
Ventilation None required
5
Programming
Programming
method
Manual (Reading special barcode) DOS
command through RS-232, Windows
configuration program
Program upgrade Enabled by built-in flash memory
Programmable
characteristics
Code type selection, check digit
selection Decoding option Decoding
option Transmitted character delay,
Header selection, trailer selection,
message suffix, good read beep tone
and volume, scanner trigger selection
Keyboard emulation type
(intermessage delay, keyboard type
and keyboard language)
Serial interface type (ACK/NAK,
Xon/Xoff, RTS/CTS, good read LED
control, start/stop bits)
6
Programming the
8110/8150/8210
To program the 8110/8150/8210, you must scan a series of
programming barcode in the correct order. Fold out the back
cover of this manual. You will see a table of alphanumeric
barcodes, which are used to program the various options
presented.
To program each option, you must:
1. Scan the Program barcode on the parameter setting part.
2. Enter the option mode by scanning the Option Bar Code
(also on the Parameter setting part).
3. To the right of the option barcode, the necessary
alphanumeric inputs are listed. Scan these alphanumeric
entries from the back fold out page. To confirm above
steps, you must scan the Finish barcode on the back fold
out page.
4. Once you have finished programming. Scan the Exit
barcode, listed on the lower right hand corner of each
parameter setting part.
7
Option Bar Code Option Alphanumeric Entry
Interface
selection
Keyboard Wedge
RS-232
Wand emulation
USB
Keyboard/RS-232
Auto detection
reserved
00＊
01
02
03
04
05
Back Fold Out
Finish barcode
Exit Barcode
Option Barcode
Program Barcode
Exit
Program
8
Interface Selection
This decoder build-in scanner comes in one model and
supports interfaces such as keyboard wedge, RS232 serial
wedge, wand emulation, and the latest USB interface. In
most of the cases, simply selecting an appropriate cable with
a device code will work for a specific interface.
Interface selection: You can change factory interface
default for other type interface. By plugging different cables,
setting right interface, then the scanner will be changed to
another interface. However, you must make sure which cable
you need.
Keyboard/RS232/USB Auto detection: By setting this
function, it will automatically select the Keyboard wedge or
RS-232 or UBS interface for user.
Program
Option Bar Code Option Alphanumeric
Entry
Interface selection
Keyboard Wedge
RS-232
Wand emulation
USB
Keyboard
/RS232/USB
Auto detection
Reserved
00
01
02
03
04＊
05
Note:＊-Default
Exit
9
Keyboard wedge
As a keyboard interface, the scanner supports most of the
popular PCs and IBM terminals. The installation of the wedge
is a fairly simple process without any changes of software or
hardware.
Keyboard Type: Select keyboard type connector of your
host computer. Scanner must be selected to the appropriate
host interface cable converter.
Program
Option Bar Code Option Alphanumeric
Entry
Keyboard type
IBM AT, PS/2
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
00＊
01
02
03
04
05
06
Exit
10
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali ZBA Lettore di codici a barre
Manuali Lettore di codici a barre popolari di altre marche
POSMicro
POSMicro Datalogic PowerScan D7100 Manuale utente
Marson
Marson MT780 Guida rapida alla configurazione
NCR
NCR RealPOS Manuale utente
Motorola
Motorola SE3300 Guida rapida alla configurazione
Element
Element P130BT Manuale utente
Motorola
Motorola Symbol LS3008 Manuale di installazione e funzionamento
