Zephyr AIN-M80AWX Guida rapida

www.zephyronline.com

Wave

AWA-M90AWX

AWA-M90ABX

Incline

AIN-M80AWX

AIN-M80ASX

RANGE HOOD - Installation and use instructions

ENGLISH........................................3

FRANÇAIS...................................33

- 6 -

LIST OF MATERIALS

Incline

- Zephyr blower sold separately

- Non-ducted recirculating kit sold separately

- Duct cover accessory sold separately

Box Cover (box

marked “120 VAC

Input”)

Box marked “120

VAC Input”

Led

Mesh Filter

Hardware Packet

Remote Blower Collar with

Damper (External motor)

Remote Blower Box Cover

Remote Blower Box

Electrical System Box

Remote Blower Wiring Extension

Remote Blower Wiring Harness

- 7 -

LIST OF MATERIALS

Wave

- Zephyr blower sold separately

- Non-ducted recirculating kit sold separately

- Duct cover accessory sold separately

Box Cover (box

marked “120 VAC

Input”)

Box marked “120

VAC Input”

Led

Mesh Filter

Hardware Packet

Remote Blower Collar with

Damper (External motor)

Remote Blower Box Cover

Remote Blower Box

Electrical System Box

Remote Blower Wiring Extension

Remote Blower Wiring Harness

- 8 -

DUCTING CALCULATION SHEET

Maximum Duct Length:

For satisfactory air movement, the total duct length

should not exceed 100 equivalent feet.

- 9 -

HOOD SPECIFICATIONS

Incline

- 10 -

HOOD SPECIFICATIONS

Wave

- 11 -

WIRING DIAGRAM

- 16 -

INSTALLING THE DUCTWORK:

INTERNAL BLOWER

NOTE: To reduce the risk of fire, use only

metal ductwork.

1. Decide where the ductwork will run

between the hood and the outside.

2. A straight, short duct run using a minimum

6” round duct will allow the hood to perform

most efficiently.

3. Long duct runs, elbows, and transitions will

reduce the performance of the hood. Use

as few of them as possible.

4. Install a roof or wall cap. Connect round

metal ductwork to cap and work back

towardshoodlocation.Useducttapetoseal

the joints between ductwork sections

(Fig.7). FIG. 7

ROOF CAP

OPTIONAL

DUCT COVER

HOOD

22” MINIMUM ABOVE COOKING

SURFACE

WALL

CAP

6” ROUND DUCT

FIG. 8

FIG. 9

Model Incline

Model Wave

FIG.10

Model Wave

PREPARE FOR INSTALLATION

ModelIncline

Remove the (2) screws and take off the front

panel. See Fig. 8.

Model Wave

1. Open the upper front glass; remove the

lower glass unscrewing (2) screws and

moving it upward (Fig.9).

2. Remove the metal panel unscrewing (6)

screws. Fig. 10.

- 17 -

INSTALLATION INTERNAL

BLOWER

NOTE: The following instructions are for

installingtheinternalblower only.

Installthisrangehoodonlywithinternalblower

model CBI-290A or CBI-600A.

1. Remove the knockout (B). Fig. 13.

2. Fix the internal blower with (4) mounting

screws (supplied with the internal blower).

Fig. 13.

(4) MOUNTING SCREWS

(Supplied with the motor)

CHOOSE AIR OUTLET

LOCATION

The hood is supplied with upper air outlet;

but you can let the air out the back, turning

the motor plate.

Rotation of the motor plate:

1.Remove the motor plate unscrewing (6)

screws (Fig.11).

2.Rotate the motor plate and re-fix in the new

position (Fig.12).

In the installation with internal blower, use

the rond knockout (B);

in the installation with remote or In-line

blower, use the other knockout (A).

FIG.11

FIG.12

FIG.13

KNOCKOUT

(B) KNOCKOUT

(A)

KNOCKOUT

(B)

- 18 -

REMOTE BLOWERS (EXTERNAL AND IN-LINE)

CAUTION: To reduce risk of fire and electric shock, install this range hood only with External

Blower Model CBE-1000, and In-Line Blower Model PBN-1000A. Other blowers cannot be

substituited.

INSTALLING THE DUCTWORK: REMOTE BLOWER

NOTE: To reduce the risk of fire, use only metal ductwork.

1. Choose the location where the External Blower or In-Line Blower will be mounted. See

illustrations below for mounting location suggestions and restrictions.

2. A straight, short duct run using a minimum 8” round duct will allow the hood to perform

most efficiently.

3. Long duct runs, elbows and transitions will reduce the performance of the hood. Use as

few of them as possible. Larger ducting may be required for best performance with long

duct runs.

4. After the Exterior or In-Line Blower has been installed, connect round metal ductwork

and work back towards the hood location. Use duct tape to seal joints between ductwork

sections.

Roof Pitch w/

Flashing & Cap

in-line

blower

(blower

housing)

external blower

Attic or crawl space

(blower

housing)

Roof Pitch w/

Flashing & Cap

in-line

blower

(blower

housing)

external blower

Attic or

crawl

space

(blower

housing)

Altri manuali per AIN-M80AWX

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Zephyr Cappa di ventilazione

Zephyr

Zephyr Monsoon DCBL AK9428AS Guida all'installazione

Zephyr

Zephyr Tidal I Guida all'installazione

Zephyr

Zephyr ZRO-E30BS Manuale utente

Zephyr

Zephyr Ombra Guida all'installazione

Zephyr

Zephyr Roma Pro ZRP-E36BS Guida all'installazione

Zephyr

Zephyr Glide EGL-E30AS Guida all'installazione

Zephyr

Zephyr Pyramid Guida all'installazione

Zephyr

Zephyr Typhoon AK2100 Guida all'installazione

Zephyr

Zephyr AK9134B Guida all'installazione

Zephyr

Zephyr AK7000 Guida all'installazione

Zephyr

Zephyr HORIZON DHZ-M90AMWX Manuale utente

Zephyr

Zephyr Venezia ZVE-E30CS Guida all'installazione

Zephyr

Zephyr ALU-E43ASX Manuale utente

Zephyr

Zephyr Tidal II AK7400AS Guida all'installazione

Zephyr

Zephyr ZTR-M90S Guida all'installazione

Zephyr

Zephyr Titan Island AK7736AS Guida all'installazione

Zephyr

Zephyr ES1-E30AB Guida all'installazione

Zephyr

Zephyr LAYERS WALL DLA-E42ASSX Manuale utente

Zephyr

Zephyr AK7036BS Guida all'installazione

Zephyr

Zephyr ZPY-E30AB Guida all'installazione

Zephyr

Zephyr AK6500 series Use Guida all'installazione

Zephyr

Zephyr Anzio Island Guida all'installazione

Zephyr

Zephyr ACT Siena ZSI-E30BS-ES Guida all'installazione

Zephyr

Zephyr AKI 124S Use Guida all'installazione

Manuali Cappa di ventilazione popolari di altre marche

emmeti

emmeti RECUPA MED A-140 Guida

Nibe

Nibe F135 Manuale utente

Kuppersberg

Kuppersberg INTRO 60 Istruzioni di installazione e manutenzione

Hisense

Hisense MH6INBG Manuale utente

Miele

Miele DA 1255 Manuale utente

Broan

Broan 46000 Manuale utente

GE Profile PV977 Istruzioni originali

FALMEC

FALMEC FFRIA24W5FS Manuale utente

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuale utente

Küppersbusch

Küppersbusch DX ISLA Manuale utente

ETNA

ETNA AV360RVS Manuale utente

JUNO

JUNO JDF603E6 Manuale utente

Miele

Miele DA 6708 D Manuale utente

Tricity Bendix

Tricity Bendix LE 150 Manuale

AEG

AEG X68163BV1 Manuale utente

AEG

AEG 125 D Manuale utente

Smeg

Smeg KSEV97X Manuale utente

Nibe

Nibe S Series Guida utente