Zephyr Tempest AK0714 Guida all'installazione

www.zephyronline.com

Use, Care and Installation Guide

Tempest I , II

Stainless Steel

Backsplash

AK0710 - 30”

AK0716 - 36”

AK0712 - 42”

AK0718 - 48”

SEP16.0301

AK0714 - 54”

Table of Contents

LIST OF MATERIALS —————————–- 2

SPECIFICATION ———————————— 3

INSTALLATION ————————————- 4,5

CLEANING AND

CONTACT INFORMATION ———————— 6

1

List of Materials

1 - Upper Section

1 - Lower Section

2 - Wire Racks

1 - Hardware Packet

2 - Retaining Clips

4 - Hinge Clips

6 - 7/16” Carriage Head Bolts

8 - 5/8” Philips Head Wood Screw

6 - Carriage Head Bolt Nuts

Note: If any parts are missing, please call

1-888-880-8368 for replacements.

2

Specifications

3

30”,36”,42”,48”,54”

Installation

1. Mark a level line on the wall at 16” below bottom of hood.

2. Position the lower section of backsplash (flat part with flange on top) on the wall.

Center it side to side and mark the top and bottom holes. Remove the lower section from

the wall.

3. If installing onto drywall only and not onto studs, insert wall anchors (we recommend EZ

anchors) into the marked holes. If installing onto studs, attach screws without EZ anchors.

4. Attach lower section of backsplash to wall with screws provided.

5. Position upper section of backsplash by engaging its flange with the lower section. Push up

to fully engage flanges*, center it side to side and mark the location of the mounting holes.

Remove the upper section from drywall and install wall anchors into marked holes.

5b.If hood is already installed, attach wall anchors into the (3) holes from inside the hood at the

bottom. These are the holes which the upper section will line up with and mount to the wall.

6. Insert retaining clips and hinge clips to the upper section. The retaining clips go in the top

top two openings and the hinge clips go in the bottom four openings. (see diagram, page 4)

Fasten and tighten nuts to the clips on back of the upper section with the provided

hardware.

7. Attach upper section to wall with screws provided. If hood is already installed, Insert the top

2” lip of the upper section behind the bottom of the hood and line up the holes with the (3)

holes at the bottom of the hood. Insert screws into holes and fasten upper section to wall.

*note: in some installations, the flanges will not fully engage in the final install. This is fine

since the weight of the upper section will rest against the bottom section.

4

30”,36”,42”,48”,54”

Installation

1. For the warming plate option; snap the wire shelves into hinge clips

on the backsplash as shown in the left side shelf diagram.

2. For the spice rack option; attach shelf to hinge clips, as

show in the right side shelf diagram, then rotate shelf upwards and

secure with retaining clip.

5

30”,36”,42”,48”,54”

Cleaning and Contact Information

Cleaning of the backsplash should be done frequently to preserve the

life of the stainless steel. Cleaning should typically be done once or

twice a month depending on your cooking habits.

When cleaning, use a non abrasive cleaner, do not use “orange”

cleaner. Abrasive cleaners may scratch the surface and discolor the

stainless steel. To clean the wire racks, soak them in soapy water.

DO NOT place in a dishwasher as this may discolor the wire racks.

You may also polish the stainless steel by using stainless steel polish.

Make sure when polishing to go along with the grain of the backsplash.

Zephyr Ventilation

2277 Harbor Bay Parkway

Alameda, CA 94502

1-888-880-8368

6

Questo manuale è adatto per i seguenti modelli

4

Indice

Altri manuali Zephyr Cappa di ventilazione

Zephyr

Zephyr Willow AK8800AS Guida all'installazione

Zephyr

Zephyr Luce ZLU-E30BS Guida all'installazione

Zephyr

Zephyr Bogart EBO-E42ASX Guida all'installazione

Zephyr

Zephyr Milano WallZMI-M90AG Guida all'installazione

Zephyr

Zephyr ACT Siena ZSI-E30BS-ES Guida all'installazione

Zephyr

Zephyr ZPA-M90S Guida all'installazione

Zephyr

Zephyr ZPY-E30AB Guida all'installazione

Zephyr

Zephyr Essentials ZAN-E30CS Guida all'installazione

Zephyr

Zephyr Siena Pro ZSP-E42BS Guida all'installazione

Zephyr

Zephyr Roma Groove ZRG-E30BS Guida all'installazione

Zephyr

Zephyr Tornado Glo Guida all'installazione

Zephyr

Zephyr Pisa ZPI-E30AG290 Guida all'installazione

Zephyr

Zephyr ASL-E42ASX Manuale utente

Zephyr

Zephyr AIN-M80AWX Guida rapida

Zephyr

Zephyr Monsoon II Guida all'installazione

Zephyr

Zephyr Twister AK8000AS Guida all'installazione

Zephyr

Zephyr ZMD-E42AS Guida all'installazione

Zephyr

Zephyr AK9028AS Guida all'installazione

Zephyr

Zephyr AK7048BS Guida all'installazione

Zephyr

Zephyr ZAN-E24CS Guida all'installazione

Zephyr

Zephyr Pyramid ZPY-E30S Guida all'installazione

Zephyr

Zephyr AK9034AS Guida all'installazione

Zephyr

Zephyr Roma Pro ZRP-E36BS Guida all'installazione

Zephyr

Zephyr Venezia ZVE-E30S Guida all'installazione

Manuali Cappa di ventilazione popolari di altre marche

emmeti

emmeti RECUPA MED A-140 Guida

Nibe

Nibe F135 Manuale utente

Kuppersberg

Kuppersberg INTRO 60 Istruzioni di installazione e manutenzione

Hisense

Hisense MH6INBG Manuale utente

Miele

Miele DA 1255 Manuale utente

Broan

Broan 46000 Manuale utente

GE

GE Profile PV977 Istruzioni originali

FALMEC

FALMEC FFRIA24W5FS Manuale utente

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuale utente

Küppersbusch

Küppersbusch DX ISLA Manuale utente

ETNA

ETNA AV360RVS Manuale utente

JUNO

JUNO JDF603E6 Manuale utente

Miele

Miele DA 6708 D Manuale utente

Tricity Bendix

Tricity Bendix LE 150 Manuale

AEG

AEG X68163BV1 Manuale utente

AEG

AEG 125 D Manuale utente

Smeg

Smeg KSEV97X Manuale utente

Nibe

Nibe S Series Guida utente