Zigen HAX-44/HDBT Manuale utente
! ! !
!
zigencorp.com Toll Free: 877-650-5252
International: +1 818-654-5252
Zigen HAX-44/HDBT HDMI 2.0 UHD
600 MHz 4x4 Matrix Switch w/HDCP
2.2 & WebOS. Mirrored Long
Distance HDBaseT POE 70M Ports.
HAX-44/HDBT
USER MANUAL Ver. 1.0
! !!
!
2"
ZIG-HAX-44/HDBT"USER"MANUAL!
!
Table of Contents
Copyright and Trademark 3
Introduction 4
Package Contents 4
Features 4
Specifications 5
Block Diagram 8
General Operation 9
Dip Switch Settings 10
Remote Control 12
WebOS 13
Commands 16
Warranty 18
! ! !
!
zigencorp.com Toll Free: 877-650-5252
International: +1 818-654-5252
Copyright and Trademarks:
All rights reserved by ZIGEN, INC. No part of this document may be reproduced
in any form or by any means without written permission from the product
manufacturer. Changes are periodically made to the information in this
document. They will be incorporated in subsequent editions. The product
manufacturer may make improvements and /or changes in the product described
in this document at any time.
All the registered trademarks referred to this manual are belonging to their
respective companies.
Before You Begin
Follow all instructions marked on the device during using.
Do not attempt to maintain the device by yourself, any faults, please contact your
vendor.
§Provide proper ventilation and air circulation and do not use near water.
§It is better to keep it in a dry environment.
§The system should be installed indoor only.
§Only use the power cord supplied with the device.
§Do not use liquid or aerosol cleaners to clean the device.
§Always unplug the power to the device before cleaning.
§Unplug the power cord during lightning or after a prolonged period of
non-use to avoid damage to the equipment.
! !!
!
4"
ZIG-HAX-44/HDBT"USER"MANUAL!
!
Introduction
The New 600 MHz HDMI matrix switch designed for switching in home and
commercial environments where switching of high-bandwidth UHD (up to
2160P60 4:4:4) content is required. The HAX-44/HDBT features 4 HDMI 2.0
Inputs and 4 HDMI 2.0 outputs.
The HAX-44/HDBT includes two 70 meter (228') HDBaseT mirrored ports (ports
2 & 4) with IEEE 802.11af POE (48V) and includes two HDBaseT POE receivers.
All HDMI and HDBaseT Ports are HDCP 2.2 compliant enabling high value
content playback and distribution.
Digital and analog audio de-embedding - with volume control is provided for each
output.
For installation and control an Ethernet port and WebOS are included providing
access for switching, EDID management, firmware updates, remote reset and
3rd party control and more.
Bi-directional IR - The HAX-44/HDBT is controllable via built in IR receiver.
Additionally, full bi-directional IR with IR routing is included.
Bi-directional RS-232 - A serial connection is provided for 3rd party control
connection and device control.
HAX-44/HDBT routes Ethernet and is compliant with the entire Zigen ecosystem
of products by routing network commands and control in receiver nodes.
Typical Applications:
•Classrooms, Boardrooms, Conference rooms for switching UHD content
sources via multiple control options (3rd party controllers, WebOS, simple
remote or front panel buttons)
•High-end home theaters for switching UHD 2.0 content with HDCP 2.2
copy protection
•Long distance applications where the rack is up to 70 meters from the
display.
!
! ! !
!
zigencorp.com Toll Free: 877-650-5252
International: +1 818-654-5252
Package Contents
•1 x HAX-44/HDBT
•2 x HAX-POE-RX Receivers
•IEC USA AC Cord 3’
•Remote Control
•1 x User Manual
Features
•HDMI 2.0 (600 MHz UHD) on all HDMI ports.
•18 GBP/sec video bandwidth HDMI, 10.2 GBP/sec HDBaseT
•WebOS Interface
•Supports digital video formats up to 4K UHD (2160P60 @4:4:4 pixel
format)
•Advanced EDID management.
•Supports uncompressed PCM 2- Ch., 5.1, 7.1, Dolby Digital, DTS, Dolby
TrueHD, DTS HD-Master Audio and more.
•Built in IR sensor plus 3.5mm jack and remote control
•Bi-directional IR plus IR routing on all ports
•Bi-directional RS-232 – Control switch or integrate 3rd party control.
•SPDIF (coax) and PCM (L/R) ports for audio de-embedding of each output
•HDCP 2.2 compliant - all ports
•2 HDBaseT receivers included
Specifications
Video Bandwidth
HDMI - 18 GBP/sec
HDBaseT - 10.2 GPBS Max
Video Resolutions
All SMPTE & VESA in HDMI 2.0 Specification. Max SMPTE UHD -
4096x2160P60/RGB/4:4:4 8-bit.
Max for HDBaseT port is 2160P60/4:2:0 8-bit (HDBaseT/CAT limitation)
! !!
!
6"
ZIG-HAX-44/HDBT"USER"MANUAL!
!
Color Space
RGB, YUV
Color Bit Depth
8-bit, 10-bit, 12-bit & 16-bit per pixel
Note: Resolution and video bandwidth limited – ex. 2160P60 RGB or 4:4:4 8-bit
would use almost the entire 18 GBPS of bandwidth. 2160P60 4:2:2 10-bit (new
Blu Ray) would exceed the previous 10.2 GBPS maximum of HDMI 1.4a and
would not be able to travel over category cable using HDBaseT as of this writing.
Chroma Subsampling
4:4:4, 4:2:2, 4:2:0
See note above – chroma subsampling or color compression is related to bit
depth and video resolution settings with regard to total bandwidth requirements.
A 4K/60 signal at 4:4:4 chroma subsampling can have a maximum bit depth of 8
bits.
Audio
HDMI in & Out – Up to Dolby TrueHD and DTS-HD Master
SPDIF – Up to Dolby Digital & DTS 5.1
Audio Sampling Rates – Up to 1536 KHz
Distance - HDMI – Up to 5M @ 4K, HDBaseT – Up to 100M at 4K/60 4:2:0 8-
bit
HDCP - 2.2, 1.4 or None
CEC - Pass through
Connections
4 x HDMI type A HDMI Input
4x HDMI type A HDMI Output
2 x RJ45 HDBaseT 70M Ports (2 & 4)
! ! !
!
zigencorp.com Toll Free: 877-650-5252
International: +1 818-654-5252
4 x SPDIF (coax) Digital Audio Outputs - 1 per output port
1 x RJ45 LAN Port for TCP/IP Control
1 x 9-pin RS-232 port
4 x 3.5mm global IR In ports
4 x 3.5mm global IR Out ports
1 x 5-pin Locking IR Connection (phoenix) in/out 3-12 VDC
1 x IR Sensor (In) - built in on front panel
1 x IEC 110-220VAC
Temperature – Operating 32-122 F (0-50 C), Humidity: 20-90% non-
condensing.
Dimensions
1RU – Rack Mountable
HDBaseT Receivers - 3x3x1 inch
Weight
3 Pounds
Certifications/Compliance
FCC, HDBaseT, CE, RoHS, HDCP, HDMI
! !!
!
8"
ZIG-HAX-44/HDBT"USER"MANUAL!
!
! ! !
!
zigencorp.com Toll Free: 877-650-5252
International: +1 818-654-5252
Block Diagram – Zigen ZIG-HAX-44/HDBT
General Operation
HAX-44/HDBT is the ultimate in high-bandwidth UHD switchers. With a full 600
MHz pixel clock the HAX-44/HDBT support high bandwidth sources and displays.
Additionally, the HAX-44/HDBT supports HDCP 2.2 copy protection so you can
be sure your customer is able to view the latest 4K UHD content – either
protected (movies) or computer content (un-protected).
Basic connections are 4 HDMI 2.0 sources (or below) and one HDMI output to
the display or projector. There is a SPDIF port that de-embeds audio from the
currently selected input and routes it to your audio matrix or multi-zone amplifier.
Additionally, with the HAX-44/HDBT there is a 100 meter HDBaseT port for long
distance runs. Note HDBaseT is limited to 4K/60 4:2:0 8-bit.
Advanced EDID management is available through a combination of the 4-pin
dipswitch and WebOS. 15 EDID tables are available, plus you can load custom
EDID tables. Or, leave the HAX-44/HDBT in the default mode and it will pull the
EDID from the connected/selected display. By being able to manage the EDID
and HPD (Hot Plug Detection) you can speed up switching in mixed format
systems.
Control the HAX-44/HDBT via the supplied remote control (IR – to built-in sensor
or run an IR receiver to the 3.5mm IR jack). You can also control the HAX-
44/HDBT via 3rd party control, RS-232, LAN (WebOS/Telnet), or via the input
selector switch on the front panel.
DIP Switch Settings
DIP 1: EDID
OFF (UP): As a default the downstream EDID is copied and used from output
port 1.
While DIP 1 is OFF (UP) DIP 2 & 3 are active as follows:
DIP 2: (OFF/UP) audio according to downstream capabilities
DIP 2: (ON/DOWN) audio is restricted to 2-channel regardless of downstream
EDID.
DIP 3: (OFF/UP) audio according to downstream capabilities.
! !!
!
10"
ZIG-HAX-44/HDBT"USER"MANUAL!
!
DIP 3: (ON/DOWN) audio is modified for SPDIF maximum capabilities. This
ensures that the SPDIF output always outputs all SPDIF supported formats.
DIP 2 overrides DIP 3. If DIP 2 is down, stereo is selected.
While DIP 1 is ON (DOWN) the EDID is selected using the WebOS
WebOS has 15 EDID tables to select from (more to come) for various use cases
(see screen shot below). Additionally via the WebOS and custom EDID table can
be loaded into the device. This gives maximum flexibility as customers can load
any EDID they want for the desired application.
Screen Shot – EDID Tables in WebOS
Note: While DIP 1 is ON (DOWN), DIPs 2 and 3 are not used.
DIP 4: Hot Plug Force
UP (OFF) – Hot Plug Detection (HPD) is normal
Indice
Altri manuali Zigen Interruttore
Zigen
Zigen SW-41Plus Manuale utente
Zigen
Zigen SW-41Plus Manuale utente
Zigen
Zigen ZIG-SW41 Manuale utente
Zigen
Zigen SW-41Plus Manuale utente
Zigen
Zigen SW-42Plus Manuale utente
Zigen
Zigen ZIG-SW42 Manuale utente
Zigen
Zigen ZIG-POEWP-100TX Manuale utente
Zigen
Zigen SW-42Plus Manuale utente
Zigen
Zigen SW-42Plus Manuale utente
