ZKTeco 1D Manuale utente
1D Barcode Scanner
Quick Start Guide
Due to the regular upgrades of systems and products, ZKTeco could not guarantee exact
consistency between the actual product and the written information in this manual.
Setting Code
Procedure
System Settings
The code scanner can set the corresponding function by reading
one or a group of special setting barcodes.
The following are the operation steps for the manual barcode
reading mode:
Factory Default
Read the "Factory Default" barcode, you can reset all the proper-
ties of the scanner to the factory default state.
Version
Read the“Version”barcode to view the current version information
of the scanner.
Press and hold the barcode scanner’s trigger button until the
aiming line activates and a red aiming line appears.
Align the red aiming line with the center of the barcode, then
move the scanner and adjust the distance between it and the
barcode to get the best reading distance.
The code reading is complete when the success prompt
sounds and the red lighting line disappears at the same time.
The barcode scanner transmits the decoded data to the host.
1.
2.
3.
Factory Default
Version
-1-
Sounding Settings
Read the setting barcode to turn on or o the prompt sound
when the barcode is successfully read.
Enable Decode Sound
Reading Mode
Manual Reading Mode
The manual reading mode is the default mode. The scanner
begins reading the code when you press the trigger button The
code reading stops after the code reading is successful or the
trigger button is released.
Continuous Reading Mode
In this mode, the scanner is in a continuous scanning mode, it will
automatically reads the barcode and outputs information. The
same barcode cannot be read more than once unless it is
removed and read again.
Disable Decode Sound
Manual Reading Mode
Continuous Reading Mode
-2-
[1C] Version: 1.2
Communication Interface Settings
USB Mode
The USB mode is the USB-KBW interface. For data transfer, the
code scanner uses a USB interface; the USB-KBW communication
is the default. It will use USB keyboard input mode, and it is not
necessary to install the drivers.
TTL/RS232 Mode
The scanner must fully match the serial communication protocol
parameters of the host device to ensure accurate data transfer
when using a serial communication interface.
Serial port communication protocol default parameters: baud
rate 9600, check character NONE.
Baud Rate
The baud rate is the number of bits transmitted per second in
serial data communication. The baud rate used by the scanner and
the data receiving host device must be synchronized to ensure
accurate data transmission.
When using the same barcode scanner to communicate with
dierent hosts, you must set the code scanner to the appropriate
communication interface mode.
USB Mode
TTL/RS232 Mode
9600
-3-
Sux Settings
115200
You can add dierent sux functions if you read the setting code.
Add CR
Add CR+LF
Add Tab
Transfer Speed
You can set dierent transmission speeds if you read the setting
code.
NONE
High Speed
-4-
Medium Speed
Low Speed
Indication Light and Buzzer
Ultra Low Speed
Successful Scan: The light ash once time.
Voice Prompt: The buzzer will beep once, when the code is
successfully read.
ZKTeco Industrial Park, No. 32, Industrial Road,
Tangxia Town, Dongguan, China.
Phone : +86 769 - 82109991
Fax : +86 755 - 89602394
www.zkteco.com
Copyright ©2023 ZKTECO CO., LTD. All Rights Reserved.
Altri manuali ZKTeco Lettore di codici a barre
Manuali Lettore di codici a barre popolari di altre marche
POSMicro
POSMicro Datalogic PowerScan D7100 Manuale utente
Marson
Marson MT780 Guida rapida alla configurazione
NCR
NCR RealPOS Manuale utente
Motorola
Motorola SE3300 Guida rapida alla configurazione
Element
Element P130BT Manuale utente
Motorola
Motorola Symbol LS3008 Manuale di installazione e funzionamento
