ZKTeco C3 Manuale utente

ZK Access Quick Start Guide





Install C3 using TCP/IPmode of communication

C3 controller supports the connection from panel to server over RS485 data line and also via

nodes on TCP/IP Ethernet networks. This greatly increases the flexibility of installation options.

Note: Make sure the devices are in the same LAN network with server or directly connect to the

server using the TCP/IP communication.

TCP/IP Connection Cable Mode

There are two ways to connect to C3 controller.

○

1Network cable directly connects Management host and the device, without a hub.

○

2In a large office a hub/switch is needed to connect more than 2 devices.

The configuration is as follows:



TCP/IP Communication

How to add a device into ZKAccess software?

ZKAccess provides two ways to add a device.

○

1When the IP address of the device is already known, you can quickly add it by entering

the IP address as follow:

Click [Add] on the [Device-Device] interface.

ZK Access Quick Start Guide





As the interface appears, write the [Device Name], then give the [IP address] of the device. The

[IP Port No.] is defaulted to 4370 by the system. Please set the password if needed.

Note: Select the type of the device. If it is a Four-Door-One-Way Access Control Panel there will

appear an extra option-[Switch to Two-door Two-way]. Select as appropriate according to

the actual device.

Select the [Area] the device belongs to. If you do not want to clear the data (Information in Time

zones, Access Levels, etc.) in the device when adding, remove the check beside the [Clear Data in

the Device when adding] option. Click [OK] to add the device.

○

2Click [SearchAccess Control Panels] option on the [Device-Device] interface.

Click [Search], after searching, the usable device will show in the results list. Modify the IP

address to available IP, and then add the device.





ZK Access Quick Start Guide





Using fast search tool to modify the IPaddress of a device

ZK provides a fast search tool for searching devices and modifying the IP addresses. This allows

devices to be added directly without modifying the system, which is inconvenient and time

consuming.

The tool and the operation of searching and modifying are as follows:

Click [Search Panel] on the [Setting] dropdown menu.

After a few seconds results for the usable devices will appear.

Click to select the device and [Modify IPAddress] on the [Setting] dropdown menu to modify the

IP address of the devices.

Indice

Altri manuali ZKTeco Controllori di accesso IP

Manuali Controllori di accesso IP popolari di altre marche

Jantar

Jantar REX A-1-9 Manuale utente

2N

2N Access Unit Foglio di istruzioni

Kedacom

Kedacom KSCA120 Series Manuale utente

H3C

H3C WX2880X Manuale utente

G4S

G4S S870-EX Guida

PRASTEL

PRASTEL M2000PE Manuale utente

Allegion

Allegion interflex IF-281 Cylinder Manuale utente

TECOM

TECOM TS1067E Manuale utente

Fermax

Fermax Memokey 100C Guida utente

Fermax

Fermax CITYLINE MEMOKEY Manuale di istruzioni

Software House

Software House iSTAR Pro 2U RM Manuale di istruzioni

AKCP

AKCP SP+ Manuale utente

Bpt

Bpt HNA/102 Manuale utente

Civintec

Civintec CV9601T-T-1F Manuale utente

BioMax

BioMax N-X90W Manuale utente

FingerTec

FingerTec s-Kadex Manuale utente

H3C

H3C WX5002ACCESSCONTROLLER Manuale utente

C Prox Ltd

C Prox Ltd DPN-2 Manuale utente