ZKTeco ProCapture-WP Manuale utente
QUICK START GUIDE
Applicable Models: ProCapture-WP
Version: 1.0
Date: July, 2017
1
Safety Precautions
Before installation, please read the following safety precautions for user
safety and to prevent product damage.
Do not install the device in a place subject to direct sun light, humidity, dust
or soot.
Do not place a magnet near the product. Magnetic objects such as magnet,
CRT, TV, monitor or speaker may damage the device.
Do not place the device next to heating equipment.
Do not to let liquid like water, drinks or chemicals leak inside the device.
Do not let children touch the device without supervision.
Do not drop or damage the device.
Do not disassemble, repair or alter the device.
Do not use the device for any purpose other than those specified.
Clean the device often to remove dust on it. In cleaning, do not splash water
on the device but wipe it out with smooth cloth or towel.
Contact your supplier in case of a problem!
2
Device Overview
2.4-Inch Color Screen
Touch Keypad
Doorbell & LED Indicator
Fingerprint Sensor & Card
Reader Area
Reset Button
Front
Left Side
Back
3
Product Dimensions & Installation
Product Dimensions
Mounting the Device on Wall
7.96 in
(202.3 mm)
3.81 in
(96.8 mm)
1.38 in
(35mm)
7.34 in
(186.5 mm)
3.0 in
(76.1 mm)
Fix the back plate onto the wall using wall mounting screws.
Note: We recommend drilling the mounting plate screws into solid
wood (i.e. stud/beam). If a stud/beam cannot be found, use supplied
drywall plastic anchors.
Insert the device to back plate.Use security screws to fasten the
device to back plate.
0.51 in
(13 mm)
4
Power Connection
Without UPS
With UPS (Optional)
Recommended Power Supply
12V DC Adaptor
GND
+12V
12V DC Adaptor
12V±10%, at least 500MA.
To share the power with other devices, use a power supply with higher
current ratings.
5
Ethernet Connection
LAN Connection
Network Cable Adaptor
Ethernet Cable
Note: The device can be connected to PC directly by Ethernet cable.
6
RS485 Connection
RS485 Fingerprint Reader Connection
RS485 Fingerprint Reader
DIP Settings
1. There are six DIP switches on the back of RS485 fingerprint reader,
switches 1-4 are for RS485 address, switch 5 is reserved, switch 6 is for
reducing noise on long RS485 cable.
2. If RS485 fingerprint reader is powered from the terminal, the length of
wire should be less than 100 meters or 330 ft.
3. If the cable length is more than 200 meters or 600 ft., the number 6
switch should be ON as below.
7
Lock Relay Connection
Device Not Sharing Power with the Lock
COM1
+12V
GND
GND Sensor NC1
FR107
Diode
12V DC Adaptor
Normally Closed Lock
Notes:
1. The system supports NO LOCK and NC LOCK. For example the NO
LOCK (normally opened at power on) is connected with 'NO1' and
'COM1' terminals, and the NC LOCK (normally closed at power on) is
connected with 'NC1'and 'COM1' terminals.
2. When electrical lock is connected to the Access Control System, you
must parallel one FR107 diode (equipped in the package) to prevent
the self-inductance EMF from affecting the system.
Do not reverse the polarities.
8
Lock Relay Connection
Device Sharing Power with the Lock
COM1
+12V GND
Sensor NC1
FR107
Diode
Normally Closed Lock
GND
9
Wiegand Output Connection
WD0
WD1 GND
Indice
Altri manuali ZKTeco Controllori di accesso IP
ZKTeco
ZKTeco FaceKiosk-H10A Manuale utente
ZKTeco
ZKTeco ProBio Manuale utente
ZKTeco
ZKTeco Green Label ProCapture-T Manuale utente
ZKTeco
ZKTeco F19 Manuale utente
ZKTeco
ZKTeco KF1000-U Manuale utente
ZKTeco
ZKTeco KF1000 Series Manuale utente
ZKTeco
ZKTeco LockerPad-7B Manuale utente
ZKTeco
ZKTeco ProBio Manuale utente
ZKTeco
ZKTeco P160 Manuale utente
ZKTeco
ZKTeco SpeedFace-V5L Manuale utente
ZKTeco
ZKTeco X8-BT Manuale utente
ZKTeco
ZKTeco ProMA Series Manuale utente
ZKTeco
ZKTeco F18 Manuale utente
ZKTeco
ZKTeco F6 Manuale utente
ZKTeco
ZKTeco Horus Manuale utente
ZKTeco
ZKTeco BioPro SA20 Manuale utente
ZKTeco
ZKTeco SpeedFace-V5L Manuale utente
ZKTeco
ZKTeco FA50 Manuale utente
ZKTeco
ZKTeco RevFace15 Manuale utente
ZKTeco
ZKTeco F18I Manuale utente
