ZKTeco PA22 Manuale utente
PA22
Version: 1.0
Quick Start Guide
Due to the regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between
the actual product and the written information in this manual.
Side
Bottom
Back Plate
Reset Button
Speaker
USBSlot
Front
Back
2.4InchTFTLCD
Keypad&
RFCardArea
LEDIndicator
Near-infraredPalm
RecognitionSensor
Tamper switch
Terminal Block
Wiring Hole
Mounting Hole
1
Device Overview
2
6.29"
(159.8mm)
4.97"
(126.1mm)
3.18"
(80.7mm)
0.76"
(19.4mm)
1.61"
(41.0mm)
47.24"
(1.2m)
Baseline
1
2
124
3
Install on the Wall
(56.1mm)
2.21"
Device Dimensions
Device Installation
Attach the mounting template sticker to the wall, and drill the holes according
to the mounting paper.
Fix the back plate on the wall with using wall mounting screws.
Attach the device to the back plate from top to bottom.
Fasten the device to the back plate with a security screw.
1.
2.
3.
4.
3
485B
485A
GND
TXD
RXD
GND
WD1
WD0
RS485B
RJ45-1
RJ45-2
RJ45-3
RJ45-6
AUX
GND
BELL-
BELL+
SEN
GND
BUT
NO1
COM1
NC1
AL-
AL+
BEEP
GLED
RLED
IWD1
IWD0
GND
12VOUT
BEEP
Green LED
Red LED
GND
+12V
Ethernet
RS232
Lock
Power Out
Sensor
Button
Power In
Auxiliary
In
Bell
Alarm
Wiegand
Out
Wiegand
In
8 Pin Cable Connectors
7 Pin Cable Connectors
4 Pin Cable Connectors
12 Pin Cable Connectors
2 Pin Cable Connectors
Terminal Block
4
Standalone Installation
Alarm
Bell
Lock
TCP/ IP
Exit Button
Door Sensor
ALARM
Wireless Router
5
GND
+12V DC
12V DC Adaptor
Power Connection
Without UPS
GND
+12V DC
With UPS (Optional)
12V±10%, at least 3000MA.
Use an AC adapter with a higher current ratings to share the power with other
devices.
Recommended Power Supply:
Ethernet Connection
LAN Connection
Network Cable Adaptor
1
2
3
4
5
6
7
8
1
4
RJ45-1
RJ45-2
RJ45-3
RJ45-6
Default IP address: 192.168.1.201
Subnet mask: 255.255.255.0
IP address: 192.168.1.130
Subnet mask: 255.255.255.0
Door Sensor, Exit Button, Alarm & Bell Connection
Door Sensor
Bell
Alarm
Exit Button
12V DC Adaptor
+12V DCGND
AUX
GND
BELL-
BELL+
SEN
GND
BUT
NO1
COM1
NC1
AL-
AL+
1
12
6
Connect the device and the software over an Ethernet cable. An example is
shown below:
Click [Comm.] > [Ethernet] > [IP Address], input the IP address and click
[M/OK].
Note: In LAN, the IP addresses of the server (PC) and the device must be in the
same network segment when connecting to ZKBio Access IVS software.
7
Lock Relay Connection
12V DC Adaptor
Magnetic Lock
+12V DC GND
FR107
Device Not Sharing Power with the Lock
AUX
GND
BELL-
BELL+
SEN
GND
BUT
NO1
COM1
NC1
AL-
AL+
DO NOT REVERSE
THE CONNECTION.
V- V+
NC NO
COM
Magnetic Lock
FR107
Device Sharing Power with the Lock
AUX
GND
BELL-
BELL+
SEN
GND
BUT
NO1
COM1
NC1
AL-
AL+
V- V+
NC NO
COM
AC Adapter
DC 12V, 3A
GND
+12V
1
2
DO NOT REVERSE
THE CONNECTION.
The system supports both Normally Opened Lock and Normally Closed Lock. The
NO Lock (Normally Opened when powered) is connected with “NO” and “COM”
terminals, and the NC Lock (Normally Closed when powered) is connected with
“NC” and “COM” terminals. The power can be shared with the lock or can be used
separately for the lock, as shown in the example with NC Lock below:
1
12
1
12
8
RS485 Connection
RS485 Fingerprint Reader Connection
RS485 Fingerprint Reader
DIP Settings
485-
485+
GND
+12V
GND
Distance:
more than 200 meters
1
8
485B
485A
GND
TXD
RXD
GND
WD1
WD0
12V DC Adaptor
There are six DIP switches which are located on the back of RS485 ngerprint
reader: switches 1 to 4 are for RS485 address, switch 5 is reserved, switch 6 is for
noise reduction on long RS485 cable.
If the RS485 ngerprint reader is powered from the terminal, the length of
wire should be less than 100 meters or 330 feet.
The number 6 switch should be turned on if the cable length exceeds 200
metres or 600 feet as shown below.
1.
2.
3.
9
Wiegand Output Connection
Controller
?
READER 1
BEEP
GLED
WD1
WD0
GND
+12V
485B
485A
GND
TXD
RXD
GND
WD1
WD0
Wiegand Input Connection
BEEP
GLED
RLED
IWD1
IWD0
GND
12VOUT
1
7
Wiegand Reader
BEEP
GLED
RLED
DATA1
DATA0
GND
+12V
AC Adapter
DC 12V, 3A
GND
+12V
1
8
1
2
Altri manuali per PA22
1
Indice
Altri manuali ZKTeco Terminale touch
ZKTeco
ZKTeco ZK3530 Manuale utente
ZKTeco
ZKTeco Green Label ProCapture-T Manuale utente
ZKTeco
ZKTeco ZKAIO1000W Manuale utente
ZKTeco
ZKTeco F Series Manuale utente
ZKTeco
ZKTeco U1000F Manuale utente
ZKTeco
ZKTeco VT07-C22L Manuale utente
ZKTeco
ZKTeco D3 Series Manuale utente
ZKTeco
ZKTeco ZKBio710 Series Manuale utente
ZKTeco
ZKTeco D1s Manuale utente
ZKTeco
ZKTeco TF1700 Manuale utente
ZKTeco
ZKTeco SpeedFace - V5L Manuale utente
ZKTeco
ZKTeco FaceDepot 7B Manuale utente
ZKTeco
ZKTeco MB10-VL Manuale utente
ZKTeco
ZKTeco ZPAD+ Manuale utente
ZKTeco
ZKTeco IM20 Manuale utente
ZKTeco
ZKTeco iFace Series Manuale utente
ZKTeco
ZKTeco iClock 885 Manuale utente
ZKTeco
ZKTeco uFace Plus Series Manuale utente
ZKTeco
ZKTeco ma 300 Manuale utente
ZKTeco
ZKTeco ProBio(QR) Manuale utente
