Zoom 4401 Manuale utente

AP+4

U S E R G U I D E

Contents

Overview........................................................................... 5

Installing the AP+4 .......................................................... 6

Connecting the Hardware............................................... 7

Setting Up the AP+4....................................................... 8

Monitoring AP+4 Status ................................................ 16

Operating Mode ............................................................. 19

Wireless Configuration ................................................. 20

Basic Settings .............................................................. 20

Active Wireless Client Table......................................... 23

Wireless Security.......................................................... 24

Access Control ............................................................. 27

WDS Settings............................................................... 28

Site Survey................................................................... 29

Advanced Settings ....................................................... 31

WiFi Protected Setup™ (WPS) .................................... 34

TCP/IP Settings.............................................................. 37

LAN Interface ............................................................... 37

WAN Interface.............................................................. 39

Firewall Settings ............................................................ 50

Port Filtering................................................................. 50

IP Filtering .................................................................... 52

MAC Address Filtering ................................................. 53

URL Filtering ................................................................ 54

Port Forwarding............................................................ 55

DMZ ............................................................................. 56

Denial of Service .......................................................... 57

VPN Settings .................................................................. 61

VPN Setup (Client)....................................................... 63

Advanced VPN Settings for IKE................................... 67

Management................................................................... 69

Statistics....................................................................... 69

DDNS ........................................................................... 70

Time Zone Settings ...................................................... 72

Log ............................................................................... 73

Upgrade Firmware........................................................ 75

Save/Reload Configuration .......................................... 76

Password Setup ........................................................... 77

Troubleshooting ............................................................ 78

Zoom Customer Support .............................................. 83

Regulatory Information ................................................. 85

Package Contents

The AP+4 package contains the following:

•AP+4

•Power cube

•Ethernet cable

•Quick Start

•CD containing warranty information and

this documentation

If anything is missing or damaged, please contact Zoom

Customer Support or the vendor from whom you purchased the

AP+4.

Overview

You can use the AP+4 as a Router/Access Point, Universal

Repeater, Ethernet Client or Wireless ISP.

•

As a Router/AP, the AP+4 handles local network traffic both

wirelessly and through its four LAN (Local Area Network)

ports, and communicates via its WAN (Wide Area Network)

port to an ADSL modem, cable modem, or other Internet-

connected device.

As a Repeater, the AP+4 is placed near the edge of a

wireless network – for example, a Zoom X6 network – and

wirelessly links up to 200 more devices to the network.

As an Ethernet Client, the AP+4 connects via its LAN ports

to up to four game consoles or computers, and links them

wirelessly to a Zoom X6 or other wireless router.

As a Wireless ISP, the AP+4 can connect up to four wired

PCs or game consoles, give them Network Address

Translation protection, and connect them wirelessly to an

access point. If you select this mode, use the Wireless

Basic Setup page to configure the AP+4 as a wireless

client.

See Setting Up the AP+4 on page 8to choose an operating

mode.

This User Guide provides instructions for connecting and

configuring your AP+4 and setting up wireless and wired local

area networks. It includes details about security, firewalls, Virtual

Private Networks and administrative tasks.

When we update information about the AP+4, the information is

provided at this Zoom web site:

http://www.zoom.com/techsupport/wirelessg_support.html

Installing the AP+4

This chapter provides basic instructions for connecting the

hardware and configuring the AP+4 using the Setup Wizard. If

you have already done this by following the instructions in the

printed Quick Start, skip to Chapter 2, Wireless Configuration,

on page 20.

AP+4 Back Panel Connectors

Connector Description

WAN This port connects to the LAN or Ethernet port of an

ADSL or cable modem, using an Ethernet cable.

LAN 1 - 4 These Local Area Network ports connect via Ethernet

cable to up to four computers, game consoles or other

network devices.

PWR This port connects to a live power source using the

supplied power cube.

RESET To reset the modem to its factory settings, insert a

paper clip and press and hold for 10 seconds.

6 Zoom AP+4 User Guide

Chapter 1. Installing the AP+4 7

Connecting the Hardware

1Put the AP+4 near a computer to be used for setup. That

computer needs an Ethernet (LAN) port.

2Turn off the computer.

3Connect one end of the supplied power cube to the AP+4

PWR jack, and the other end to a live power source.

Important! Only use the power cube shipped with the AP+4.

Other power cubes may damage the device.

The PWR LED on the AP+4 front panel should turn on and

the WLAN LED should flash. (The WLAN LED continues to

flash to signify broadcast activity as long as the Wireless

LAN is enabled. It is enabled by default.)

4Connect one end of the supplied Ethernet cable to the

computer’s Ethernet port and the other end to one of the

AP+4’s LAN ports.

5Turn on the computer.

The WLAN LED continues flashing and the connected LAN

port and the ACT (Activity) LEDs become steady on. (If you

have a 10 Mbps Ethernet connection, the LAN LED does not

turn on.)

If you want the AP+4 to have access to the Internet, connect

its WAN port to the Ethernet port on your cable modem,

ADSL modem, or other broadband device. When you do

this, the WAN LED turns on if the broadband device is on

and its Ethernet port is working.

8 Zoom AP+4 User Guide

LED Status The AP+4 is . . .

PWR Steady connected to a power source

WLAN Flashing

Steady

broadcasting its SSID (network name)

not broadcasting its SSID and therefore

not available to wireless devices

seeking a wireless network connection

WAN Steady

Flashing

connected either wirelessly or via

Ethernet cable to a broadband modem

that connects to the Internet

transmitting or receiving data

LAN 1-4 Steady connected via Ethernet cable to up to

four computers or gaming devices

ACT

(Activity)

Steady

Flashing

connected via the associated LAN port

to a computer or other network device

transmitting or receiving data via the

associated LAN port

Setting Up the AP+4

1Open your web browser, enter 10.0.0.200 in the address

bar, and press the Enter key to open the Zoom AP+4

configuration software. The Status page appears first.

2In the left pane, select Setup Wizard.

3On the Welcome page, click Next.

4On the Choosing an Operating Mode page, select the way

you want to use the AP+4:

Router/Access Point. In this mode, which is the one most

users will select, the AP+4 links all wireless enabled

computers and other devices to a network and gives those

devices shared access to your broadband Internet

connection.

If you are using the AP+4 as a Repeater, on the Wireless

Basic Setup page at the Mode option, select AP+WDS.

Then, on the WDS Settings page, enter the MAC addresses

of access points you are communicating with.

Ethernet Client. This mode lets up to four computers, game

consoles or other devices plug into the AP+4 for wireless

access to a wireless network. (In this mode, the AP+4 acts

as a full bridge, just passing data back and forth between the

Internet and network devices.)

Wireless ISP. In this mode, the AP+4 connects to the

Ethernet ports of up to four wired PCs or game consoles,

and connects those devices wirelessly to a wireless access

point. Use this mode if you know you need to use the AP+4's

NAT functionality. Most users who need to connect a

computer or game console to an access point should set up

the AP+4 as an Ethernet Client instead.

If you select Wireless ISP mode, use the Wireless Basic

Setup page to configure the AP+4 as a wireless client.

Click Next to continue.

Chapter 1. Installing the AP+4 9

5To have the AP+4’s clock automatically updated by an NTP

server, on the Selecting a Time Zone page, select a Time

Zone and an NTP Server, and click Next.

6If you need to set up or modify your wired local network, use

the LAN Interface Setup page (see page 37 of this manual

for more information).

7If you want to connect to the Internet, select the method on

the Setting Up Internet Access page.

•

If you are among the great majority of customers who

are using the AP+4 as a Router/Access Point or with a

cable modem, at WAN Access Type select DHCP

Client.

If you select DHCP Client and at the end of the

installation process you have not connected successfully

to the Internet, it is possible that you are running PPPoE

software. In that case, at WAN Access Type select

PPPoE (Point-to-Point Protocol over Ethernet). Then

enter the User Name and Password given to you by

your service provider.

10 Zoom AP+4 User Guide

Altri manuali per 4401

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Zoom Router di rete

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza