Zte R207-Z Manuale utente
1
R207-Z
Quick Start Guide
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
2
Getting to Know Your Device
Appearance
The following figure is for your reference only.
1. LED Indicators
2. Power Key
3. WPS Key
4. Charging/micro-USB Jack
5. (U)SIM Card Slot
6. microSDHC Card Slot
NOTE:
The microSDHC™logo is a trademark of SD-3C, LLC.
3
Getting to Know Your Device
Indicators
When the device is powered on, the following icons may be lighting.
For a description of the icons, refer to the following table.
Indicator
Status
Description
Network
Red solid
Error status. Not registered to the
mobile network, no (U)SIM card
inserted or no network service
available.
Green solid
Registered to the mobile
network.
Green
blinking
Connected to the mobile network
and data is being transferred.
Wi-Fi
Blue solid
Wi-Fi is active.
Blue
blinking
WPS is active.
off
Wi-Fi is off or your device is in
sleep mode.
SMS
Blue solid
You have unread messages.
Blue
blinking
You have new messages.
off
No unread messages.
4
Battery
Red solid /
blinking
The battery is low. Please charge
the battery.
Green
blinking
The battery is being charged or in
standby mode.
Green solid
The battery level is middle or
high.
off
Your device is not being charged,
or the battery is not inserted.
Getting to Know Your Device
Connection Scenarios
The device can access the Internet in two ways and it allows multiple
clients to surf on the Internet at the same time. The following figures
are for your reference only.
3G Mode: A (U)SIM card can be used to access the Internet.
Internet Wi-Fi Mode: Your device can be connected to a WLAN
device (such as a hotspot device or wireless router) through Wi-Fi
to access the Internet. The WLAN device must be already
connected to the Internet.
5
NOTE: Your device and the WLAN device must be in different
subnets.
Installing Your Device
1. Slide the back cover and remove it.
NOTE:
Do not remove the cover rudely.
2. Install a (U)SIM card to the (U)SIM card slot.
WARNING!
Your device does not support the micro-SIM and nano-SIM card or
any other non-standard SIM cards. To avoid damaging the device, do
not use those cards or any card holders.
6
3. Install the microSDHC card if necessary.
4. Install the battery.
7
5. Close the back cover.
Connecting to Your Device
Using Wi-Fi
1. Power on your device.
2. Make sure your computer or other client devices have enabled
Wi-Fi, and search for available wireless networks.
NOTE:
Refer to your Wi-Fi-enabled client device manual for further details on
how to search for wireless networks. If you use a computer, you
need to set your computer to obtain an IP address automatically.
8
3. Select the Wi-Fi name (SSID) of your device, and click Connect.
4. Enter the Wi-Fi password if necessary, and click OK.
NOTE:
Refer to the chapter Getting to Know the Wi-Fi SSID and Password
to get the default Wi-Fi SSID and password.
5. Wait until the client device is connected to your device successfully.
Using a USB Cable
1. Connect a computer to your device with a USB cable.
2. Power on your device. The operating system detects and identifies
new hardware, and automatically installs the hardware.
NOTE:
If the system does not automatically launch installation, you can click
the device installation icon in My Computer to install the software.
3. Wait until the computer is connected to your device successfully.
Getting to Know the Wi-Fi SSID and
Password
You can view the label on the device to get the default Wi-Fi SSID and
password.
9
Logging in to the 3G Mobile Hotspot
Configuration Page
1. Make sure the connection between your device and the client
device is correct.
2. Launch the Internet browser and enter http://192.168.0.1 or
http://ufi.ztedevice.com in the address bar.
NOTE:
It is recommended that you use IE (7.0 or later), Firefox (15.0 or later),
Opera (10.0 or later), Safari (4.0 or later), or Google Chrome (10.0 or
later).
3. Enter the password to log in to the 3G Mobile Hotspot configuration
page.
NOTE:The default password is admin.
Changing the Wi-Fi SSID or Password
1. Log in to the 3G Mobile Hotspot configuration page.
2. Select Settings > Wi-Fi Settings > Basic Settings.
3. Change the Network Name (SSID) or the Pass Phrase
( Password).
4. Click Apply.
10
Accessing the Internet
3G Mode
After a client device is successfully connected to your device, you can
access the Internet in Automatic or Manual mode. The default mode
is Automatic.
Mode
Operation
Automatic
Your device is automatically connected to the
Internet, and you can surf on the Internet through
the client.
Manual
1. Log in to the 3G Mobile Hotspot configuration
page.
2. Select Settings > Network Settings >
Dial-up Settings > WAN Connection
Mode > Manual, and then click Apply.
3. Select Home, and click Connect or
Disconnect.
NOTE:
To modify the parameters of your device, log in to the 3G Mobile
Hotspot configuration page.
Internet Wi-Fi Mode
1. Log in to the 3G Mobile Hotspot configuration page.
2. Select Settings > Internet Wi-Fi.
3. Set the Internet Wi-Fi Switch and Preferred Network, and click
Apply.
Indice
Altri manuali Zte Router di rete
Zte
Zte ZXR10 3800-8 Manuale utente
Zte
Zte Avid 4G LTE Manuale utente
Zte
Zte ZXV10 W300 Manuale utente
Zte
Zte E1200 Manuale utente
Zte
Zte ZXR10 GER Manuale utente
Zte
Zte ZXR10 3800-8 Istruzioni per l'installazione
Zte
Zte Z1320 Manuale utente
Zte
Zte ZXV10 Manuale utente
Zte
Zte MC7010 Manuale utente
Zte
Zte ZXR10 3800-8 Istruzioni per l'installazione
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza