ZTechnik Quantum Z5402 Istruzioni per l'installazione
Item Description P rt No. Qty.
1 Headlight Guard with Quantum® Hardcoat 1
B g#1154
2 elcro Hook 77-771159-000 9
3 elcro Loop 77-771160-000 9
CONTENTS OF KIT
ZTechnik PO Box 158 Maywood, IL 60153-0158 USA
708-343-0400 / Fax: 708-343-0625 / www.ztechnik.com / e-mail: [email protected]
©2016 National Cycle, Inc. Page 1 of 2 10-119993-000 05/16
TOOLS REQUIRED:
T10 Torx
Grease Pencil or Crayon
Special notes and cautionary measures hich can prevent
damage to the accessory or motorcycle.
Tips for facilitation of operation, control and adjust-
ment, as ell as maintenance ork.
Note: Attention:
Thank you for purchasing a ZTechnik product. Read these instructions carefully and thoroughly before beginning work. Dealers,
if installing this windscreen for a customer, please give them this manual. It contains information needed to properly maintain
and use this product.
PREPARATION
The Velcro® Industrial grade fasteners will
securely hold your Quantum Hardcoated
olycarbonate Headlight Cover to the motorcy-
cle’s headlight.
For best performance and adhesion the
Headlight Cover and motorcycle surface
should be a minimum of 65 °F (18 °C)
Cleaning is critical. Be sure to clean the
headlight rim and remove all wax, clean-
ers, and protectants (Armor-All). These can
contaminate the adhesive causing it to fail.
Loop Hook
1
32
INSTALLATION AND OWNER’S MANUAL
Qu ntum® H rdco ted Polyc rbon te
Z5402 LED He dlight Gu rd for:
R1200GS/GSA W ter Cooled
Figure 1
Figure 2
Figure 3
ZTechnik O Box 158 Maywood, IL 60153-0158 USA
708-343-0400 / Fax: 708-343-0625 / www.ztechnik.com / e-mail: [email protected]
©2016 National Cycle, Inc. age 2 of 2 10-119993-000 05/16
Figure 4
Figure 5
INSTALLATION
1. For ease of installation, it is recommend to
remove the Headlight Rim. (T10Torx) Figure 1
2. Apply 4 pieces of Velcro Loop to Rim.
osition Velcro Dot at inside edge of Rim as
shown in inset. Figure 2
3. Align the Headlight Cover to Rim. Make 4
marks on the outside of the Guard where the
Hook will match to the Loop. Figure 3 (Grease
Penci )
4. Install Hook at the mark on the inside of the
Guard. ress down to ensure good contact of
adhesive with Guard. Figure 4
Let Velcro Hook and Loop cure for 5 minutes
before installing Headlight Guard.
5. Re-install Rim to motorcycle. (T10 Torx)
6. Install Guard. Align Loop fastener with Hook
and press into place until fully engaged. Wipe
marks from Guard. Figure 5
CLEANING AND MAINTENANCE
To clean the guard, wash with a clean soft
cloth, plenty of warm water and if necessary, a
non-abrasive soap such as dishwashing liquid.
Flannel or soft chamois make good cleaning
cloths. aint, glue residue or tar removal:
Moisten cotton with naphtha or turpentine
fo owed by a wash as above.
Do not clean the guard with abrasive cleaners,
alcohol, or strong solvents. Except as recom-
mended above for paint, glue, or tar removal.
X
Inside Surface
Indice
Altri manuali ZTechnik Accessori per motociclette
ZTechnik
ZTechnik Z8300 Istruzioni per l'installazione
ZTechnik
ZTechnik Z2450 Istruzioni per l'installazione
ZTechnik
ZTechnik Z2373 Istruzioni per l'installazione
ZTechnik
ZTechnik VStream Windscreen Z2450 Istruzioni per l'installazione
ZTechnik
ZTechnik Quantum Z5403 Istruzioni per l'installazione
ZTechnik
ZTechnik Z2353 Istruzioni per l'installazione
ZTechnik
ZTechnik R1150 R Manuale utente
ZTechnik
ZTechnik Z2240 Istruzioni per l'installazione
ZTechnik
ZTechnik Z8305 Istruzioni per l'installazione
ZTechnik
ZTechnik Quantum Z2360 Manuale utente
