3D Systems Cubify CUBEX Duo Manuale utente

1

CUBEX

Replacing a

Main Board

PCB

2

Contents

What you will need ..................................................................................................... 3

Removing the Case and floor panel. .......................................................................... 4

Removing the damaged Main Board PCB.................................................................. 6

Fitting the new Main Board PCB ................................................................................ 7

Re attaching the floor panel and case........................................................................ 8

3

What you will need

Replacement Main Board PCB

3mm Hex Driver

2.5mm Hex Driver

4

Before beginning this process please ensure that the print pad is raised to the

top of the machine, all cartridges and the jet wipe have been removed from the

machine and that you have made a note of your Z height and offset settings as

these settings will not be present on the new PCB. Unplug the CubeX from

mains power.

Removing the Case and floor panel.

Using the 3mm hex driver remove the 8 case bolts (4 either side of the machine).

Unplug the CubeX screen.

5

Lift the case up off the CubeX.

Using the 3mm hex driver undo the 5 bolts holding the floor panel to the machine.

Lift the front of the floor panel and cable tie it to the bed arms. This will allow you

access to the Main Board PCB.

6

Removing the damaged Main Board PCB

Before removing the Main board PCB, label each of the looms that are plugged into

it. The PCB is marked to tell you which loom is plugged into which connector.

Remove the Looms and unplug the power supply from the main board PCB.

Gently pull up on the main board PCB to slide it off of the rubber ties holding it in

place.

7

Using the 2.5mm hex driver, undo the bolts holding the Print Jet driver boards to the

Main Board PCB and remove the Print Jet driver boards. (Note the amount of Print

Jet driver boards will correspond with the amount of Print Jets present on your

CubeX printer)

Fitting the new Main Board PCB

Plug the Extruder Driver boards into the new Main Board PCB and fasten with bolts.

8

Pull the rubber ties up through the holes on the main board PCB to fasten it to the

CubeX.

Plug the looms and power supply back into their corresponding connectors.

Re attaching the floor panel and case.

Cut the cable tie holding the floor panel in place and gently lower it down.

9

Using the 3mm hex driver re attach the 5 bolts that hold the floor panel.

Slide the case onto the CubeX and plug in the CubeX screen.

Using the 3mm Driver re attach the 8 case bolts.

10

You may now power up your CubeX.

You will need to re activate your CubeX using the activation code associated

with your CubeX. You will also need to re set your Z height and offsets, if you

did not make a note of these settings you can find instructions on how to set

them in the CubeX users guide.

Altri manuali per Cubify CUBEX Duo

3

Indice

Altri manuali 3D Systems Stampante 3D

3D Systems

3D Systems CUBE Manuale dell'operatore

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems ProJet 4500 Manuale utente

3D Systems

3D Systems ProX 500 Manuale utente

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems ProJet 3500 Max Series Manuale utente

3D Systems

3D Systems ProJet 6000 Manuale utente

3D Systems

3D Systems Cube 2nd Generation Manuale utente

3D Systems

3D Systems ZPRINTER 150 Manuale utente

3D Systems

3D Systems PostCure 1050 Manuale utente

3D Systems

3D Systems ProJet 5500X Manuale utente

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems Cubify CUBEX Duo Istruzioni operative e di sicurezza

3D Systems

3D Systems CubePro Manuale utente

3D Systems

3D Systems ProJet 5000 Manuale utente

3D Systems

3D Systems wematter Gravity Manuale utente

3D Systems

3D Systems Geomagic Touch Manuale utente

3D Systems

3D Systems CubePro Istruzioni per il montaggio

3D Systems

3D Systems ProJet 1200 Manuale utente

3D Systems

3D Systems ZPRINTER 650 Manuale utente

3D Systems

3D Systems ProJet 660Pro Manuale utente

3D Systems

3D Systems sPro Manuale utente

3D Systems

3D Systems Cubify CUBEX Duo Manuale elenco delle parti

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente