3D Upfitters 3D Printer Carbon Air Filter Manuale utente

Carbon Air Filter/Vent Adapter

Installation Manual 2.0 !

Shipped August 17, 2019

Copyright 2019 3DUpﬁtters

1

This page intentionally left blank."

Copyright 2019 3DUpﬁtters

2

Carbon Air Filter

Locate Mounting Point

If you’ve purchased an enclosure kit from 3DUpﬁtters the mounting point will be on the

back panel when viewed from the back, as shown below."

If you’re already got an enclosure or are creating one for yourself, you’ll need to cut a

hole for air ﬂow, and four holes to mount the ﬁlter and fan. The hole should be 78mm

in diameter, and the holes are 70mm apart in a square pattern. There is a DXF ﬁle you

can download from the product page on the website if you want to laser or CNC your

DIY enclosure. Be sure to delete the dotted construction lines when conﬁguring

the laser or CNC control ﬁle.

Copyright 2019 3DUpﬁtters

3

Find Air Flow Direction

The fan is powered by a 5V USB power supply (not included). Plug in the fan and notice in

which direction the air ﬂows. You’ll want to connect the fan to the ﬁlter so that the air is pulled

out of the enclosure and through the ﬁlter."

"

Attach the Fan/Filter to the Panel

There are two sizes of holes with 3DUPﬁtters enclosures for 60mm and 80mm fans.

With the larger 80mm-sized holes the screws are inserted from inside the enclosure

and through the nuts slotted into the ﬁlter itself as shown below. The ﬁlter and fan

combination are mounted on the outside of the enclosure."

Copyright 2019 3DUpﬁtters

4

"

Smaller enclosures such as the Prusa have 60mm holes, and thus need an adapter.

You won’t need the 60mm fan, but instead will use an adapter to connect the stronger

80mm fan to push air through the ﬁlter. To prepare the 80mm to 60mm adapter insert

an M4 square nut in each corner."

Copyright 2019 3DUpﬁtters

5

The adapter is then connected to the fan/ﬁlter combination using 50mm M4 screws. Insert all

4 screws lightly before attempting to tighten."

The holes on the 60mm side will now align with the 60mm holes on your Prusa, Ender 3, or

other small enclosure, and the ﬁlter can be attached with 12mm M4 screws."

Copyright 2019 3DUpﬁtters

6

Vent Adapters

Many people ﬁnd the smell of plastic from a 3D printer to be particularly noxious, but there

hasn't been that much research on the long or short term health eﬀects of exposure to 3D

printer fumes. Because the diﬀering nature of the particles and compounds put into the air by

diﬀerent ﬁlaments, there's no standard way of ﬁltering everything, especially since the smallest

particles can't be caught by even the best HEPA ﬁlter."

If you only print occasionally the risk is low, but if you are going to be printing a lot (and

especially for multiple printers), what the CDC recommends is to vent the 3D printer gasses to

the outside, such as with one of our vents paired with a standard dryer hose. They can also

hook to any DIY enclosure by simply creating the right size hole. "

The vent adapters are designed to ﬁt to a 3” or 4” clothes dryer hose available in any hardware

store. Adjust the hose clamp to be right next to the ridge for the best ﬁt."

The adapters are intended to be ﬂexible so you can design a conﬁguration that’s best for your

situation. Here’s an example setup with the CR-10/Taz6 vent kit. For this you'd need to order a

hose, clamps, and dryer window vent from your hardware store."

Copyright 2019 3DUpﬁtters

7

 "

The Prusa/Ender setup is a bit more complicated since window inserts are all 4", while the

hose we recommend is 3". This setup adds an 3"->4" hose adapter, and the 3" hose is small

and doesn't overwhelm the small enclosure. Note that with this setup you need 2 3" clamps

and 1 4" clamp. "

 "

To complete venting to the outside you can ﬁnd ﬂexible 4" dryer duct hoses or ﬂexible 3" hoses

online or at most hardware stores. This can be connected to the outside using the same

techniques you'd use for a clothes dryer, or you can purchase one of the many compatible

window-venting kits. These items are not included and must be purchased separately. We

don't bother to stock them since they're readily available at local hardware stores. "

The fan can either be plugged into a USB power supply (not included) or the wires stripped and

connected directly into some models of 3D printer."

Copyright 2019 3DUpﬁtters

8

Indice

Altri manuali 3D Upfitters Stampante 3D

3D Upfitters

3D Upfitters LulzBot Mini 2 R1 Manuale utente

3D Upfitters

3D Upfitters BlazeCut Fire Extinguisher Manuale utente

3D Upfitters

3D Upfitters Taz6 Enclosure Kit Manuale utente

3D Upfitters

3D Upfitters Ender 3 V2/CR-6 Enclosure Kit Manuale utente

3D Upfitters

3D Upfitters CR-10 Max Enclosure Kit Manuale utente

3D Upfitters

3D Upfitters Artillery Sidewinder X1 Enclosure Kit Manuale utente

3D Upfitters

3D Upfitters Carbon Air Filter Manuale utente

3D Upfitters

3D Upfitters CR-10 Smart Pro Manuale utente

3D Upfitters

3D Upfitters Ender 3 V2/CR-6 Enclosure Kit Manuale utente

3D Upfitters

3D Upfitters Temp Sensor Manuale utente

3D Upfitters

3D Upfitters CR-10 Smart Enclosure Kit Manuale utente

3D Upfitters

3D Upfitters CR-10 Smart Enclosure Kit Manuale utente

3D Upfitters

3D Upfitters FT-5 Enclosure Kit Manuale utente

3D Upfitters

3D Upfitters Ender 5 Plus R1 Enclosure Kit Manuale utente

3D Upfitters

3D Upfitters Ender 3 S1 Enclosure Kit Manuale utente

3D Upfitters

3D Upfitters Prusa i3 MK2 Manuale utente

3D Upfitters

3D Upfitters Prusa i3 Enclosure Kit Manuale utente

3D Upfitters

3D Upfitters CR-10S Pro/CRX R1 Enclosure Kit Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente