4IPNET EAP210 Manuale utente

EAP210 V1.00

Enterprise Access Point

Quick Installation Guide

EAP210 Enterprise Access Point ENGLISH

This document is protected by USA copyright laws and other laws. Besides, the

document is the property of 4IPNET, INC. You may not copy, reproduce, distribute,

publish, display, perform, or modify any part of this publication in any form or by any

means without prior written permission from 4IPNET, INC. You may not alter or remove any

are claimed or registered marks of their respective companies or organizations.

To download up-to-date version, please visit www.4ipnet.com.

Quick Installation Guide

EAP210 Enterprise Access Point ENGLISH

FCC CAUTION

This equipment has been tested and proven to comply with the limits for a class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

---Consult the dealer or an experienced radio/TV technician for help.

The device contains a low power transmitter which will send out Radio Frequency (RF) signal when

transmitting. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20 centimeters

between the radiator and your body.

Quick Installation Guide

EAP210 Enterprise Access Point ENGLISH

iii

CE CAUTION

Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for

European Community, Switzerland, Norway, Iceland, and Liechtenstein

Model: EAP210

For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and

hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement.

• Radio: EN 300.328:

•EMC: EN 301.489-1, EN 301.489-17,

• EMC: EN 55022Class B, EN 55024:+ A1 + A2including the followings:

EN 61000-3-2, EN 61000-3-3.

EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,

EN 61000-4-5, EN 61000-4-6, EN 61000-4-11

• Safety: EN 60950-1 + A11,

Caution:

This declaration is only valid for configurations (combinations of software, firmware, and hardware)

provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by

4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.

European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range

2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be

restricted to certain frequencies and/or may require a license for operation. Contact your local regulatory

authority for compliance.

Taiwan NCC Statement

根據 NCC 低功率電波輻射性電機管理辦法規定:

第十二條

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或

變更原設計之特性及功能。

第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時應立即停用，並改善至

無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之擾。

在5.25 ~ 5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。

Quick Installation Guide

EAP210 Enterprise Access Point ENGLISH

Preface

Package Contents

4ipnet EAP210 is a high-end 802.11a/b/g/n 2.4GHz/

5GHz MIMO Selectable Dual Band Access Point

(AP) designed to maximize deployment flexibility

and feasibility for IT administrators.

Complying with the latest industrial wireless security

standards that are required in the tightly secured

enterprise network environments, EAP210 makes

the wireless communication fast, secure and easy. It

supports business-grade secure encryption -

802.1X and Wi-Fi Protected Access (WPA and

WPA2) ; by pushing a purposely built button, the

4ipWES (Press-n-Connect) feature makes it easy

to bridge wireless links of multiple EAP210s for

forming a wider wireless network coverage.

EAP210 also features multiple ESSIDs with VLAN

tags and multiple Virtual APs; great for enterprise

applications, such as separating traffic from different

departments using different ESSIDs. The PoE LAN

port is able to receive power from Power over

Ethernet (PoE) sourcing devices. Its metal case is

IP50 anti-dust compliant, which means that EAP210

is well suited to WLAN deployment in industrial

environments.

This Quick Installation Guide provides instructions

and reference materials to get you started with

4ipnet EAP210.

1. 4ipnet EAP210 x 1

2. Quick Installation Guide (QIG) x 1

3. Console Cable x 1

4. Power Adapter (DC 12V) x 1

5. Detachable Antenna x 2

It is recommended to keep the original

packing material for possible future shipment

when repair or maintenance is required. Any

returned product should be packed in its

original packaging to prevent damage during

delivery.

Quick Installation Guide

EAP210 Enterprise Access Point ENGLISH

System Overview

Front Panel

Figure 1 EAP210 Front Panel

Rear Panel

1 (1) 2 3 71 (2)4 56

Figure 2 EAP210 Rear Panel

Quick Installation Guide

EAP210 Enterprise Access Point ENGLISH

Antenna

Connector

Reverse SMA connectors for attaching antennas.

1 (1) is the primary antenna connector and 1 (2) is the secondary.

Utilize both connectors for 802.11n MIMO optimized performance.

12V 2A

Power Socket for the power adaptor.

Uplink Port

The port for uplink connection to another gateway or device. PoE (802.3af/at) is supported.

WES Button

WDS Easy Setup. Press the button to build up a WDS link with another peer. 4 WDS links

can be set up.

Restart Button

Press to restart the system

LED Indicators

Power

On indicates power on.

Status

On indicates the system is ready.

WLAN

On indicates wireless network interface is ready for service.

WES

For indicating WDS connection status.

Master (Press for more than

3 seconds)

Slave (Press once and

then release right away)

WES Start

LED (Green) OFF and then

BLINKING SLOWLY

LED (Green) BLINKS

SLOWLY

WES Negotiate

BLINKING SLOWLY

(Green)

BLINKING RAPIDLY

(Green)

WES Success

LED (Green) ON

WES Fail/Timeout

LED (Green) OFF

Console Port

To access EAP210 via the console interface

Right-Side Panel

On the right side of the panel there is a Kensington slot. Admin can also fill it with a rubber plug.

Quick Installation Guide

EAP210 Enterprise Access Point ENGLISH

Hardware Installation

Please follow the steps mentioned below to install the hardware of EAP210:

1. Place the EAP210 at the best location.

The best location for EAP210 is usually at the center of your intended wireless network.

2. Connect EAP210 to your network device.

Connect one end of the Ethernet cable to the Uplink port of EAP210 and the other end of the cable to a

switch, a router or a hub. EAP210 is then connected to your existing wired LAN network.

3. There are two ways to supply power over to EAP210.

(a) Connect the DC power adapter to the EAP210 power socket.

Please use only the power adapter supplied with the EAP210 package. Using a different power

adapter may damage this system.

(b) EAP210 Uplink port is capable of receiving DC currents. Connect an IEEE 802.3af-compliant PSE

device, e.g. a PoE-switch, to the Uplink port of EAP210 with the Ethernet cable.

Now, the Hardware Installation is completed.

To verify the wired connection between EAP210 and your switch/router/hub, please check the

LED status indication of these network devices.

Quick Installation Guide

EAP210 Enterprise Access Point ENGLISH

Getting Started

4ipnet EAP210 supports web-based configuration. When hardware installation is complete, EAP210 can be

configured through a PC by using a web browser such as Mozilla Firefox 2.0 or Internet Explorer version 6.0

and above.

The default values of LAN IP address and subnet mask of EAP210 are:

IP Address: 192.168.1.1

Subnet Mask: 255.255.255.0

Steps:

1. To access the Web Management Interface, connect the administrator PC to the LAN port of EAP210 via

an Ethernet cable. Then, set a static IP address on the same subnet mask as EAP210 in TCP/IP of your

PC, such as the following example:

IP Address: 192.168.1.100

Subnet Mask: 255.255.255.0

2. Launch the web browser on your PC by entering the IP address of EAP210 (http://192.168.1.1) at the

address field, and then press Enter.

3. The following Admin Login Page will appear. Enter “admin” for both the Username and Password fields,

and then click Login.

Administrator Login Page

Quick Installation Guide

EAP210 Enterprise Access Point ENGLISH

4. After a successful login to EAP210, a System Overview page of the Web Management Interface will

appear, as depicted below. The Radio Status and AP Status will be shown.

The Web Management Interface - System Overview Page

5. To logout, simply click on the Logout button at the upper-right corner of the interface to return to the

Administrator Login Page. Click OK to logout.

Altri manuali per EAP210

Indice

Altri manuali 4IPNET Punto di accesso wireless

4IPNET

4IPNET OWL300 Manuale utente

4IPNET

4IPNET OWL800 Manuale utente

4IPNET

4IPNET EAP717 Manuale utente

4IPNET

4IPNET EAP300 Manuale utente

4IPNET

4IPNET EAP750 V1.00 Manuale utente

4IPNET

4IPNET OWL530 v1.00 Manuale utente

4IPNET

4IPNET EAP705 Manuale utente

4IPNET

4IPNET EAP210 Manuale utente

4IPNET

4IPNET OWL610 Manuale dell'operatore

4IPNET

4IPNET EAP701 Manuale utente

4IPNET

4IPNET OWL500 Manuale utente

4IPNET

4IPNET EAP100 Manuale utente

4IPNET

4IPNET EAP210 Manuale utente

4IPNET

4IPNET EAP740 Manuale utente

4IPNET

4IPNET EAP320 V1.20 Manuale utente

4IPNET

4IPNET EAP727 Manuale utente

4IPNET

4IPNET EAP760 Manuale utente

4IPNET

4IPNET OWL550 Manuale utente

4IPNET

4IPNET EAP757 V1.00 Manuale utente

4IPNET

4IPNET EAP110 Manuale utente

4IPNET

4IPNET EAP738 Manuale utente

4IPNET

4IPNET EAP260 Manuale utente

4IPNET

4IPNET EAP737 Manuale utente

4IPNET

4IPNET EAP200 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente