A2Z Ozone MP-8000 Manuale utente
MP-8000
OperatingManual
*register your product at a2zozone.com/pages/warranty
Produced for and Distributed by:
A2Z Ozone, Inc.
Louisville, KY 40299
EPA Est.: 95432-KY-1
Active Ingredient: Ozone.
Do Not Inhale Ozone.
Keep Out of Reach of Children.
Produced by:
Bluegrass Water Technology Shenzhen Co., Ltd
China
EPA Est.: 95432-CHN-1 Version 1.2.1
1
Table of Contents
Important Safety Information ...................................................................... 2
Technical Specifications .............................................................................. 3
Features ....................................................................................................... 4
Timer Functions .......................................................................................... 6
Installation Instructions ............................................................................. 7
Operating Instructions ............................................................................... 8
Maintenance ..............................................................................................11
Troubleshooting .........................................................................................12
Warranty ....................................................................................................15
IMPORTANT:
When operating an ozone generator, please remember to remove people, pets,
and plants from the area in case of leakage. Be sure to leave the area being treated
immediately and only return once the ozone as dissipated. Under most conditions,
theareaofincidentshouldbesafe to returntoin2-4hours aftertheleakageoccurs.
Ozone has a half life of 30 minutes. Areas where ozonator is installed should be
well- ventilated.
2
Important Safety Information
READ AND FOLLOW ALL INSTRUCTIONS
• Read this manual completely before attempting installation and/or operation.
• Install in accordance with the installation instructions.
• Connect to a grounded, grounding type receptacle only.
• To reduce the risk of electrical shock, replace damaged electrical cables immediately.
• Follow all applicable electrical codes.
• Electric shock hazard. Be sure to turn power OFF and disconnect from power source
before any service work is performed. Failure to do so could result in serious injury or
death.
• DO NOT inhale ozone gas produced by this device.
• Breathing in ozone may cause shortness of breath, headaches, or lead to serious
respiratory problems.
• For your safety, do not store or use gasoline, chemicals or other flammable liquids or
vapors near this or any other appliance.
• A spontaneous and violent ignition may occur if oil, grease or greasy substances come in
contact with oxygen under pressure. These substances must be kept away from oxygen
regulators, cylinder valves tubing and connections and all other oxygen equipment.
• The use of an ozone destructor is necessary to ensure excessive ozone is safely removed
from the application.
• The use of ozone test strips or dissolved ozone monitor is required.
• PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
In accordance with California Regulations, this ozone generator is solely for industrial use and
must be installed by a professional. Potential health hazard: emits ozone.
3
Technical Specications
Model Ozone
Capacity
Oxygen
Feed Gas
Flow Rate
Dimensions Energy
Usage Concentration Unit
Weight
lbs/day g/hr LPM H x W x D V/W mg/L lbs KG
MP-8000 0.424 8 3 O2or dry
air 9.8 x 15 x 10 110/145
55 @ 2.5 LMP
w/ O2input
6 w/ internal
pump
18 8.1
Items Included:
• MP-8000 ozone generator
• MP-8000 operation manual
• 8 feet of flexible tubing included
• 8 feet of PTFE tubing
• Two 2” oblong diffuser stones included
• Spare fuse included
• Fan filter replacement
Features
1Ozone Light Indicates ozone is functioning. If the LED is illuminated, the unit is
working properly.
2Power Light Indicates when there is power to the unit. If the power is supplied,
the light will remain illuminated.
3O3Switch Used to control ozone power within the unit.
4Air Pump
Switch
Used to power on the small internal air compressor built into each
MP Series unit. If using oxygen supply, DO NOT turn on air pump
switch.
5O3Out Port Ozone produced by the unit exits through this port.
6O2In Port Optional hook up port for an external oxygen source. This can be
used to produce a more pure ozone. 3 psi & 2-4 LPM flow rate.
7Air Out Port Air outlet port for the air compressor (loops into O2In Port for
ambient air use).
8Timer (Hour) Sets a time limit for the unit to produce ozone. The unit timer
needs to be engaged for ozone production.
9Ozone
Concentration
Knob
Controls the percentage of ozone produced by the unit.
4
5
1
2
3
4
5
6
7
8 9
MP-8000
6
Timer Functions
The MP-8000 is equipped with timer functions to match a wide variety of applications. The
hourly timer knob can be adjusted between 15 minutes and 4 hours, at any time interval
between.
• 15 minutes to 4 hours
• To operate this timer, turn the knob clockwise to the desired set position.
Continuous Timer
• A continuous option is available for the MP-8000.
• To operate this timer, turn the knob counterclockwise.
Note: You can control the MP-8000 with a Gorden timer. Just turn on all switches and
position timer to “ON”. Plug the unit to the timer (15 AMP) and set the timer to run
the unit. Be sure to set the timer to cool down the unit at least 2 hours between each
runtime.
7
Installation Instructions
Ozone Generator Placement
• Install ozone generator in a clean, dry area with good ventilation.
• Place the MP unit above any water tank level.
• If pressure is lost in the venturi vacuum and the unit is below water tank level, gravity will
pull water through the ozone output hose and enter the ozone generator.
• Please look at the provided drawing for more information (Figure 1.2).
• Place stone no more than 18 inches deep.
NOTE: Place the ozone generator in room temperatures below 130 degrees F. Prolonged
exposure to extreme temperatures will void the warranty.
Venturi Installation
• Install the venturi injector with the bypass valve on water recirculation pipeline (Figure
1.1).
• The arrow on venturi should be set in the same direction as water flow.
• Turn water pump on and close the bypass valve until a vacuum is created at the venturi
input.
NOTE: Use a gauge to check vacuum -2 to -3 PSI (-0.14 to -0.21 bars) or place finger over
end of venturi valve to feel the vacuum. At this point, the air is injected into the water line.
This is observed by air bubbles inside the water tank.
NOTE: The water tank requires an exhaust to the outside of the building with an ozone
destructor to remove excessive ozone.
Main Power
• Use the power cable provided to connect the MP-8000 to a properly rated and grounded
receptacle.
• If the MP Series is used where water is present, a ground fault circuit
interrupter must protect the circuit.
8
• Plug your power cord into the back of the unit and the wall socket.
• Remove the bulkhead nut on O³out port.
• Then insert the bulkhead onto the tubing.
• Slide tubing onto the O³outlet barb.
• Screw the nut back onto the O³out port.
• Attach the diffuser stone of your choosing to the opposite end of the tubing or connect
other end to the venturi suction port.
NOTE: Be sure to set the unit above water level. A check valve can also help prevent water
from back-flowing into the unit.
For Oxygen Input:
• Disconnect the small tubing from the O²in port.
• Connect the oxygen source to the O²in port with appropriate tubing. You may use the
provided flexible tubing.
• Adjust the flow rate of the oxygen source to a maximum of 1-4 L/minute, and a
maximum of 3 PSI.
NOTE: Ensure that the air compressor switch is in the OFF position when using an oxygen
source.
For Ambient Air:
• Turn on both air compressor switch and the ozone switch, in that order.
• Keep in mind, the unit will NOT power up until the timer is set.
• Turn the power button on – it is located on the back of the unit by the power cord.
• Turn the ozone concentration knob to 100 percent or desired concentration for the given
application.
CAUTION: If ozone concentration is below 20 percent, the unit will not power up unless
external oxygen is attached. The dial can be adjusted after starting, but avoid dialing up and
down continually, as this action may harm the control board.
• Set the unit timer for the desired application duration.
• The timer can be dialed counterclockwise to allow for an “Always On” function.
• Keep in mind, this function is not recommended for oxygen air.
• At this point, the MP Unit is powered up.
Operating Instructions
9
To turn the unit off:
• For Ambient Air:
• Turn off the ozone switch.
• Wait 10 seconds before continuing.
• Turn off the air compressor switch.
• For Oxygen Air:
• Turn off the ozone switch
• Wait 10 seconds before continuing.
• Turn off the oxygen source.
Tube Connection and Start Up
An oxygen tank or oxygen generator should be used when pure ozone needed.
Using Oxygen Bottle/Tank:
• Connect oxygen bottle/tank to ozone generator (Oxygen In Port).
• Connect MP unit (Ozone Out Port) to venturi injector.
• Install a check valve 10 inches after ozone outlet tube fitting. This can be done by
cutting a tube ten inches after ozone outlet fitting.
• Connect both ends of cut tubes to the check valve. Please direct the arrow on the check
valve toward venturi injector.
• Set tank gas flow meter at 1-4 liters per minute and 3 PSI maximum.
• First, open the oxygen valve then only turn on the main ozone power switch on the front
panel of the MP unit (internal air compressor switch stays OFF). The ozone light and fan
should turn on.
• Increase power to the cells by turning the ozone concentration knob clockwise. Please
remember to make a full rotation clockwise.
• Prior to shutting off the feed gas to the unit, turn off the switch and allow the unit to
purge for about 1 minute.
• Then, turn the flow of oxygen gas off.
NOTE: Do not turn the air pump switch ON when using oxygen generator, oxygen bottle or tank.
Using Oxygen Generator:
• Connect oxygen generator (Oxygen Out Port) to ozone generator (O2In Port).
• Connect MP unit (Ozone Out Port) to the venturi injector.
• Install a check valve 10 inches after ozone outlet tube fitting. This can be done by
cutting a tube ten inches after ozone outlet fitting.
• Connect both ends of cut tubes to the check valve.
Indice
Altri manuali A2Z Ozone Generatore portatile
