Aaeon Raptor MicroATX Manuale utente

Raptor MicroAT

Motherboard

Installation Guide

Introduction

Table of Contents

Notice...................................................... IV

Introduction .......................................... V

Chapter 1 Pre-Configuration......1

Step 1 Setting the Jumpers 3

Jumper Locations ............................................................. 4

CMOS Reset....................................................................... 5

MicroATX Power Supply Enhancements........................ 5

SER C and SER D RS-232/RS-422/485 Selection

(Optional Feature) ............................................................. 5

SER C RS-422/485 Receiver Mode (Optional Feature) .. 6

SER D RS-422/485 Receiver Mode (Optional Feature) .. 6

SER C and SER D RS-422/485 Termination Resistor

Option (Optional Feature) ................................................ 7

ATA-Disk Connector Voltage Selection.......................... 8

LCD Panel Voltage Selection........................................... 8

On-Board Chipset I2C Connection to EDID EEPROM ... 8

Step 2 SDRAM, CPU, and Cables

Installation 9

Raptor MicroATX Memory Configuration ....................... 9

CPU Installation ................................................................ 9

Installing Cables ............................................................. 11

Power and Control Panel Cables................................... 11

Installing Peripheral Cables........................................... 11

Index of Connectors ....................................................... 14

Chapter 2 Embedded BIOS 2000

Setup ..............................16

Basic CMOS Configuration Setup Screen.................... 17

Features Configuration Setup Screen .......................... 22

Custom Configuration Setup Screen............................ 23

Shadow Configuration Setup Screen ........................... 25

Raptor MicroATX – Installation Guide

Reset CMOS to Last Known Values .............................. 26

Reset CMOS to Factory Defaults................................... 26

Write to CMOS and Exit.................................................. 26

Exit without Changing CMOS ........................................ 26

Chapter 3 Upgrading....................27

Upgrading the System Memory ..................................... 27

Upgrading the Microprocessor...................................... 27

Appendix A Technical

Specifications..........29

Chipsets ........................................................................... 29

System Memory .............................................................. 29

Bios .................................................................................. 30

Embedded I/O .................................................................. 30

Industrial Devices ........................................................... 31

Miscellaneous ................................................................. 32

Memory Map .................................................................... 33

DMA Channels................................................................. 33

I/O Map ............................................................................. 34

PCI Configuration Space Map........................................ 35

Interrupts ......................................................................... 35

PCI Interrupt Routing Map ............................................. 36

SMBUS ............................................................................. 37

Connectors Pin-out......................................................... 37

Appendix B Flash BIOS

programming and

codes ...........................45

Troubleshooting POST................................................... 46

Critical Error BEEP Codes ............................................. 52

Appendix C Communication

Devices .......................55

Introduction

III

On-board Ethernet .......................................................... 55

Serial Ports ...................................................................... 55

Appendix D On-Board Video

Controller...................63

Raptor MicroATX – Installation Guide

Notice

The company reserves the right to revise this publication or to change

its contents without notice. Information contained herein is for

reference only and does not constitute a commitment on the part of the

manufacturer or any subsequent vendor. They are in no way

responsible for any loss or damage resulting from the use (or misuse) of

this publication.

This publication and any accompanying software may not, in whole or

in part, be copied, photocopied, translated or reduced to any machine

readable form without prior consent from the vendor, manufacturer or

creators of this publication, except for copies kept by the user for

backup purposes.

Brand and product names mentioned in this publication may or may not

be copyrights and/or registered trademarks of their respective

companies. They are mentioned for identification purposes only and are

not intended as an endorsement of that product or its manufacturer.

First Edition.

March, 2002

Introduction

Thank you for your purchase of the Raptor MicroATX industrial

embedded motherboard. The Raptor MicroATX design was based on

the Intel 815E chipset providing the ideal platform to industrial

applications. The Raptor MicroATX design is based on the Intel

Celeron (FC-PGA) and Pentium III (FC-PGA and FC-PGA2)

processors.

With proper installation and maintenance, your Raptor MicroATX will

provide years of high performance and trouble free operation.

This manual provides a detailed explanation into the installation and

use of the Raptor MicroATX industrial embedded motherboard. This

manual is written for the novice PC user/installer. However, as with

any major computer component installation, previous experience is

helpful and should you not have prior experience, it would be prudent

to have someone assist you in the installation. This manual is broken

down into 3 chapters and 4 appendixes.

Chapter 1 - System Board Pre-Configuration

This chapter provides all the necessary information for

installing the Raptor MicroATX. Topics discussed include:

installing the CPU (if necessary), DRAM installation and

jumper settings. Connecting all the cables from the system

board to the chassis and peripherals is also explained.

Chapter 2 - BIOS Configuration

This chapter shows the final step in getting your system

firmware setup.

Chapter 3 - Upgrading

The Raptor MicroATX provides a number of expansion

options including memory. All aspects of the upgrade

possibilities are covered.

Raptor MicroATX – Installation Guide

Appendix A - Technical Specifications

A complete listing of all the major technical specifications of

the Raptor MicroATX is provided.

Appendix B - Flash BIOS Programming (optional) and Codes

Provides all information necessary to program your optional

General Software Embedded 2000 Flash BIOS. POST Codes

and beep codes are described in details.

Appendix C - Communication Devices

Two on-board 10/100 Ethernet controllers and four serial ports

(Two RS232 + Two RS232 or RS422/485(optional)).

Appendix D - On-Board Video Controller (LCD Optional)

On-board CRT video controller/LCD (optional).

Static Electricity Warning!

The Raptor MicroATX has been designed as rugged as possible but can

still be damaged if jarred sharply or struck. Handle the motherboard

with care.

The Raptor MicroATX also contains delicate electronic circuits that

can be damaged or weakened by static electricity. Before removing the

Raptor MicroATX from its protective packaging, it is strongly

recommended that you use a grounding wrist strap. The grounding

strap will safely discharge any static electricity build up in your body

and will avoid damaging the motherboard. Do not walk across a carpet

or linoleum floor with the bare board in hand.

Warranty

This product is warranted against material and manufacturing defects

for two years from the date of delivery. Buyer agrees that if this

product proves defective the manufacturer is only obligated to repair,

replace or refund the purchase price of this product at manufacturer's

Introduction

VII

discretion. The warranty is void if the product has been subjected to

alteration, misuse or abuse; if any repairs have been attempted by

anyone other than the manufacturer; or if failure is caused by accident,

acts of God, or other causes beyond the manufacturer's control.

Raptor MicroATX - An Overview

The Raptor MicroATX represents the ultimate in industrial embedded

motherboard technology. No other system board available today

provides such impressive list of features:

CPU Support

• Supports full series of Intel Celeron (FC-PGA 66MHz PSB,

FC-PGA 100MHz PSB and FC-PGA2 (0.13u) 100MHz PSB) and

Pentium III (FC-PGA 100MHz PSB, FC-PGA 133 PSB and FC-

PGA2 (0.13u) 133MHz PSB) PGA370 processors.

Supported Bus Clocks

• 66MHz, 100MHz and 133MHz.

Memory

• Two DIMM sockets up to 512MB (unbuffered) SDRAM,

PC100 and PC133 (recommended for higher performance when

using 133MHz PSB processors).

On-Board I/O

• 2 Floppies up to 2.88 MB.

• Dual channel PCI 32-bit EIDE controller – UDMA 66/100

supported. One extra connector (mini-Header 44 pin) in parallel to

IDE1 for Solid State IDE disk or any 44 pin IDE device support.

• Four high speed RS-232 (or two RS-232 and two RS-422/485

(optional)) serial ports 16 Bytes FIFO (16550/16550D). RS-

422/485 Full duplex or Half-duplex (RTS flow control),

termination resistors on/off, transient suppression on transmitter

lines.

Raptor MicroATX – Installation Guide

VIII

• One Centronics™ compatible bi-directional parallel port.

EPP/ECP mode compatible.

• One PS/2 mouse and one PS/2 keyboard connectors.

• Auxiliary Keyboard/Mouse header for front panel access.

• Two Universal Serial Bus connectors.

• Four 32-bit PCI slots.

• Two RJ45 Ethernet connectors.

• Power Button – advanced management support.

• SMBus/I2C header.

• Automatic CPU voltage & temperature monitoring device

(optional).

ROM BIOS

• General Software Embedded 2000 BIOS with optional

FLASH ROM.

On-Board Ethernet

• Two On-board 10/100 Ethernet.

On-Board CRT/LCD(Optional) video controller

• Standard CRT video controller (Intel 815E chipset).

• DVO connector (optional).

• LCD support (optional) (SmartASIC SP1015).

Conventions Used in this Manual





Notes - Such as a brief discussion of memory types.

Important Information - such as static warnings, o

very important instructions.

When instructed to enter keyboard keystrokes, th

text will be noted by this graphic.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Aaeon Scheda madre

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente