ABB A3 Series Manuale utente

Mounting hole pattern

Typical spacing shown. Automotive name plate

requires 2.5" spacing. Some accessories also

require additional spacing.

—

INSTRUCTION SHEET

A3P oil-tight push-pull operator

These instructions do not purport to cover

all details or variations in equipment nor

to provide for every possible contingency

to be met in connection with installation,

operation or maintenance. Should further

information be desired or should

particular problems arise that are not

covered sufficiently for the purchaser’s

purpose, the matter should be referred to

ABB Inc.

The contents of this instruction manual

shall not become part of or modify any

prior or existing agreement, commitment

or relationship. The sales contract

contains the entire obligation of ABB. The

warranty contained in the contract

between the parties is the sole warranty

of ABB. Any statements contained herein

do not create new warranties or modify

the existing warranty.

Cat. no.

A3PP4_ _

A3PP6__

A3PPM__

A 3P T4R _ _

A3PB4__

A3PB6_ _

A3PBE__

A3PBF_ _

—

Step 3

Disassemble before installation

Large gaskets

Index locking ring

—

Step 1

1.25

[31.8]

1.25

[31.8]

2.25

[57.2]

0.672

[17.1]

0.190

[4.8]

Ø1.210

[Ø30.7]

2.25

[57.2]

Small gasket

—

Step 2

Name plate (optional)

2 3⁄8"

Large

—

Name plates

115⁄16"

4⁄5"

Standard

4⁄5"

27⁄16"

Automotive

For replacement parts information or

an application guide, visit our website

at abb.com/low-voltage or contact

your ABB representative.

For more information on optional

mounting kits, name plates and

other accessories, visit

abb.com/low-voltage.

WARNING

Hazardous voltage. Can cause

death, serious personal injury

or property damage.

To avoid electrical shock, turn

off electrical power to controls

before performing installation

or maintenance.

Panel thickness range

(inches)

Gaskets

required

16 ga – 14 ga 3

(0.060 – 0.075)

13 ga – 10 ga 2

(0.090 – 0.135)

9 ga – 7 ga 1

(0.150 – 0.188)

—

Step 4

—

Step 5

—

Step 6a

—

Step 6b

Locknut wrench

Cat. no. A3XGLW

Assemble parts

shown. Leave the

lens and small

gasket off until

step #6.

—

Replacement bulb chart

Volts

Incandescent

bulb

LED lamp – single bulb

Red Green Yellow White Blue

6#755* A3XBL6R A3XBL6G A3XBL6Y A3XBL6W A3XBL6L

24 #757 A3XBL2R A3XBL2G A3XBL2Y A3XBL2Y A3XBL2L

120 N/A A3XBL4R A3XBL4G A3XBL4Y A3XBL4Y A3XBL4L

*Also flashing lamp #267

Tighten locking nut to 40 ± 2 in-lb [4.5 Nm] recommended torque.

Contact operation:

Torque contact block retaining screws to 8 – 10 in-lb [0.9 – 1.1 Nm]

Torque light module retaining screws to 4 – 5 in-lb [0.5 – 0.6 Nm]

Maintained push-pull

Normally open contacts — use A3XC10 contact block

Normally closed contacts — use A3XC01 contact block

Momentary push-pull (factory assembled)

Normally open contacts — use A3XC01 contact block (becomes normally open when assembled)

Normally closed contacts — use special A3XC1EL contact block which must be mounted last

Plastic lens

1. Place small gasket inside nut.

2. Insert mushroom head/pushbutton

into switch body.

3. Tighten securely by hand.

1SQC910006M0201, A5E50558178, April 2021

—

We reserve the right to make technical

changes or modify the contents of this

document without prior notice. With regard

to purchase orders, the agreed particulars

shall prevail. ABB Inc. does not accept any

responsibility whatsoever for potential

errors or possible lack of information in

this document.

We reserve all rights in this document

and in the subject matter and illustrations

contained therein. Any reproduction or

utilization of its contents – in whole or in

parts – is forbidden without prior written

—

USA

ABB Inc.

305 Gregson Drive

Cary, NC 27511

abb.com/low-voltage

Questo manuale è adatto per i seguenti modelli

Altri manuali ABB Unità di controllo

ABB

ABB TCC300 Manuale utente

ABB

ABB ACS880 Series Manuale del proprietario

ABB

ABB NPBA-01 Manuale di installazione

ABB

ABB SmissLine TP ZLS 260 Guida utente

ABB

ABB REC650 ANSI Istruzioni per l’uso

ABB

ABB FEPL-02 Ethernet POWERLINK Manuale di installazione

ABB

ABB ACS850 series Manuale utente

ABB

ABB ret650 Guida rapida

ABB

ABB 616019-T1 Manuale per l'uso e la cura

ABB

ABB Relion REC670 Istruzioni per l’uso

ABB

ABB REC650 ANSI Guida rapida

ABB

ABB ACH550 series Manuale utente

ABB

ABB CMS-660 Manuale utente

ABB

ABB RPBA-01 Manuale utente

ABB

ABB NPBA-12 Manuale di installazione

ABB

ABB MTQ22-FBP.0 Manuale utente

ABB

ABB ACS850 series Guida utente

ABB

ABB Relion 630 Series Istruzioni per l’uso

ABB

ABB TA571-SIM Manuale utente

ABB

ABB UCU-22 Manuale utente

ABB

ABB COMMANDER 300 Manuale utente

ABB

ABB TOTALFLOW WellTell Wireless IS Guida utente

ABB

ABB M4M Manuale di istruzioni

ABB

ABB ACS 600 MultiDrive Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente