ABB FSCA-01 Manuale di installazione

Options for ABB drives, converters and inverters

Quick installation and start-up guide

FSCA-01 RS-485 adapter module

Safety instructions

WARNING! Obey the safety instructions. If you ignore them, injury or death, or damage to the

equipment can occur. See the user’s manual.

Mechanical installation

Electrical installation

Layout of the module

1. Pull out the lock.

2. Install the module carefully to an option

module slot of the drive. See the drive

hardware manual.

3. Push in the lock.

4. Tighten the screw to torque 0.8 N·m using

a Torx TX10 screwdriver.

WARNING! Do not use excessive force,

or leave the screw too loose. Over-

tightening can damage the screw or

module. A loose screw decreases the EMC

performance, and can even cause an operation

failure.

13

4







No. Description

1Lock

2 Mounting and grounding screw

3 Bus connector [X1]

4 Termination jumper [J2]

5 Diagnostic LEDs

5

3

2

4

1

Start-up

When the module is connected to the drive, the drive control program sets the applicable parameters.

See the appropriate drive manual.

Basic parameter settings

Register address when theABB Drives - Classic communication profile is used.

To take the settings into use, validate and refresh the parameters with parameter 51.27 FBA par refresh.

Further information

Index Name Value

20.01 Ext1 commands Fieldbus A

22.11 Speed ref1 source FBAA ref 1

28.11 Frequency ref1 source FBAA ref 1

50.01 FBAA enable Enable (or select the option slot in which the module is installed)

50.02 FBAA comm loss func Fault

51.02 Profile The ABB Drives - Classic communication profile is the default value.

51.03 Station ID Set the address of the device.

51.04 Baud rate Set the baud rate of the link.

51.05 Parity Set the use of parity and stop bit(s) and the data length.

Register Address Register Data (16-bit)

(4)00001 ABB Drives Profile Control Word

(4)00002 Reference 1

(4)00003 Reference 2

(4)00004 ABB Drives Profile Status Word

(4)00005 Actual 1

(4)00006 Actual 2

(4)00101…(4)09999 Drive ParameterAccess (16-bit); RegisterAddress = (4)00000 + 100 × Group + Index

(4)20000…(4)29999 Drive ParameterAccess (32-bit); RegisterAddress = (4)20000 + 200 × Group + 2 × Index

See the latest version of FSCA-01 RS-485 adapter module

user's manual (3AUA0000109533 [English]) inABB library

(www.abb.com/drives/documents).

For more information on fieldbus options and protocols

provided by ABB Drives, see the fieldbus

communications web page

(new.abb.com/drives/connectivity/fieldbus-connectivity).

Pin allocation for [X1] Bus termination with [J2]

Pin Description

1 SHDL Bus cable shield

2 DATA_A Data positive

3 DATA_B Data negative

4 GND_B Isolated signal ground

Termination activated Termination deactivated

3AXD50000158546 Rev A (EN) 2017-11-23

FSCA-01 manual

Fieldbus communications web page

Altri manuali per FSCA-01

2

Indice

Altri manuali ABB Unità di controllo

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente