ABB Zenith ZTG 30 Manuale utente

OPERATION, MAINTENANCE, AND INSTALLATION GUIDE

Zenith ZTG series

For ZTG(D) series automatic transfer

switches, 30-1200 A, 200-480 Vac

—

Receiving, handling and storage

Receiving and handling

Upon receipt, carefully inspect the trans-

fer switch for damage that may have oc-

curred during transit. If damage is evi-

dent, or there is visible indication of

rough handling, immediately file a dam-

age claim with the transportation com-

pany, and notify your local ABB sales

office.

Do not remove the shipping packaging

until ready to install the switch.

Storage

If the unit will not be placed into service

immediately, store the transfer switch in

its original package in a clean, dry loca-

tion. To prevent condensation, maintain a

uniform temperature. Store the unit in a

heated building, allowing adequate air cir-

culation and protection from dirt and

moisture. Storing the unit outdoors could

cause harmful condensation inside the

transfer switch enclosure.

HAZARD OF EQUIPMENT

OVERTURNING

When moving with a fork lift, do not re-

move the shipping packaging until the de-

vice is in its final location.

Failure to follow this instruction may

result in personal injury or equipment

damage.

Warning

Indicates a hazardous situation that,

if not avoided, could result in death or

serious injury.

Zenith ZTG Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE

—

Read these safety instructions

carefully before using this product!

HAZARD OF ELECTRIC SHOCK,

EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective

equipment and follow safe electrical

work practices.

• This equipment must only be installed

and serviced by qualified electrical per-

sonnel.

• Before performing visual inspections,

tests, or maintenance on the equip-

ment, disconnect all sources of electric

power. Assume that all circuits are live

unless they are completely de-ener-

gized, tested, grounded, and tagged.

Pay particular attention to the design of

the power system. Consider all sources

of power, including the possibility of

backfeeding.

• Disconnect all sources of electric power

before removing or making source side

or load side connections to the transfer

switch.

• Always use a properly rated voltage

sensing device at all line and load con-

nections to confirm transfer switch is

disconnected from all live electrical

sources.

• Turn off power supplying transfer

switch before doing any other work on

or inside switch.

Failure to follow these instructions could

result in death or serious injury.

Danger

Indicates a hazardous situation that,

if not avoided, will result in death or

serious injury.

—

Operation, maintenance,

and installation

instruction

Automatic transfer

switches, Zenith ZTG

series ATS

INSTALLATION INSTRUCTIONS,

ZENITH ZTG SERIES ATS,

CHAPTERS 9–11

OPERATION AND MAINTENANCE

INSTRUCTIONS, ZENITH

ZTG SERIES ATS,

CHAPTERS 1–8

Zenith ZTG Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE

—

Operation and

maintenance instruction

Automatic transfer

switches, Zenith ZTG

series ATS

1. Introduction 11

1.1 Hazard Categories 11

1.2 Definitions 12

1.3 Warranty 13

1.4 Product Specification 14

2. Product overview 15

2.1 General overview 16

2.1.1 Operation types 17

2.2 HMI 18

2.3 Zenith ZTG series features 19

2.4 Typical applications 22

2.5 Sequence of operations 24

2.5.1 Switching sequence / Automatic 24

2.6 Special features description 30

2.6.1 Automatic configuration 30

2.6.2 In-phase monitor 30

2.6.3 Powering supply scenarios 30

Zenith ZTG Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE

3. General operation 31

3.1 Position indication 31

3.2 Operating and locking 32

3.3 Manual handle operation 33

3.4 Return to automatic mode,

operating by HMI 35

3.5 LED functionality in HMI 36

3.6 Using HMI 38

3.6.1 Keypad 38

3.6.2 Navigating in menu 38

4. Navigating HMI menu 39

4.1 Start screens 39

4.2 Using main menu and setting parameters 41

4.3 Menus and parameters 42

5. Electronic accessories 53

5.1 Using Ekip Connect -software 54

5.2 Using Ekip Bluetooth-module 55

5.2.1 LED indications 55

5.3 Using Ekip Programming -module 56

5.3.1 LED indications 56

5.4 Auxiliary power supply module 57

5.4.1 Electrical characteristics 57

5.4.2 LED indications 57

5.5 Using Ekip Signalling 2K-_ -module 58

5.5.1 Electrical characteristics of 58

Ekip Signalling 2K-_ -module

5.5.2 Access from the display / 58

Ekip Signalling 2K-_ -module

5.5.3 LED indications and inputs/outputs 61

of Ekip Signalling 2K-_ -module

5.6 Using Ekip Com _ -modules 62

5.6.1 Ekip Com Modbus RTU -module 62

5.6.2 Ekip Com Profibus DP -module 65

5.6.3 Ekip Com DeviceNet -module 68

5.6.4 Ekip Com Modbus TCP -module 72

5.6.5 Ekip Com Profinet -module 76

5.6.6 Ekip Com EtherNet/IP -module 79

6. Troubleshooting 83

6.1 Alarms 83

6.2 Warnings 85

6.3 Information 86

7. Technical data 87

7.1 General technical data 87

7.2 Circuit diagrams 90

7.3 Overall dimensions 92

8. Maintenance 95

Zenith ZTG Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente