Accu-Scope 3002 Manuale utente

Table of Contents

Safety Notes………………………………………………….…. i

Care and Maintenance………………………………………... ii

1. Component Illustration ……………………………………… 1

2. Installation of Components ………………………………….. 2

3. Adjusting Components……………………………………….. 7

4. Operation……………………………………………………… 9

5. Technical Specifications …………………………………….. 12

6. Component List ………………………………………………13

7. Trouble Shooting Guide …………………………………….. 14

SAFETY NOTES

1. Open the shipping carton carefully to prevent any accessory, i.e. objectives or eyepieces, from

dropping and being damaged.

2. Do not discard the molded Styrofoam container; the container should be retained should the

microscope ever requires reshipment.

3. Keep the instrument out of direct sunlight, high temperature or humidity, and dusty environments.

Ensure the microscope is located on a smooth, level and firm surface.

4. If any specimen solutions or other liquids splash onto the stage, objective or any other component,

disconnect the power cord immediately and wipe up the spillage. Otherwise, the instrument may

be damaged.

5. CAUTION: the lamp, lamp housing and adjacent parts will become very hot. Do not touch these

parts until they have completely cooled. Never attempt to handle a hot halogen bulb.

6. All electrical connectors (power cord) should be inserted into an electrical surge suppressor to

prevent damage due to voltage fluctuations.

7. For safety when replacing the halogen lamp or fuse, be sure the main switch is off (“O”), remove

the power cord, and replace the halogen bulb after the bulb and the lamp house has completely

cooled.

8. Confirm that the input voltage indicated on your microscope corresponds to your line voltage. The

use of a different input voltage than indicated will cause severe damage to the microscope.

CARE AND MAINTENANCE

1. Do not attempt to disassemble any component including eyepieces, objectives or focusing

assembly.

2. Keep the instrument clean; remove dirt and debris regularly. Accumulated dirt on metal surfaces

should be cleaned with a damp cloth. More persistent dirt should be removed using a mild soap

solution. Do not use organic solvents for cleansing.

3. The outer surface of the optics should be inspected and cleaned periodically using an air stream

from an air bulb. If dirt remains on the optical surface, use a soft cloth or cotton swab dampened

with a lens cleaning solution (available at camera stores). All optical lenses should be swabbed

using a circular motion. A small amount of absorbent cotton wound on the end of a tapered stick

makes a useful tool for cleaning recessed optical surfaces. Avoid using an excessive amount of

solvents as this may cause problems with optical coatings or cemented optics or the flowing

solvent may pick up grease making cleaning more difficult. Oil immersion objectives should be

cleaned immediately after use by removing the oil with lens tissue or a clean, soft cloth.

4. Store the instrument in a cool, dry environment. Cover the microscope with the dust cover when

not in use.

5. ACCU-SCOPE microscopes are precision instruments which require periodic servicing to

maintain proper performance and to compensate for normal wear. A regular schedule of

preventative maintenance by qualified personnel is highly recommended. Your authorized

ACCU-SCOPE distributor can arrange for this service.

bino

3002 BINOCULAR MICROSCOPE SERIES

Eyepiece

Binocular Viewing Head

Nosepiece

Objective

Body

①

②

2.1 Installation of Components

The diagram shows the numerical order to assemble the microscope. Inspect all optical surfaces for dust

and debris; clean if necessary. Do not use force to install any component; all components should be

installed without strain.

Body

Objectives

ÅBinocular Viewing Head

Eyepieces

④

③

Power Cord

2. Installation Procedure

Figure 1

Figure 3

Figure 2

Installation of the Binocular

Viewing Head (Figures 1 & 2)

Insert the binocular viewing head into

the head of the body; ensure that the

dovetail is completely seated into the

body; tighten the thumb screw. Do not

release the head from your hand grip

until you are sure the head is installed

securely.

Installation of the Eyepieces

(Figures 3 & 4)

Remove the protective caps from the

eyepiece tubes. Insert the eyepieces into

the eyepiece tubes.

Figure 4

Figure 6

Figure 5

Figure 7

Installing the Objectives (Figures 5 &6)

1: Adjust the coarse focus knob until the mechanical stage

is at its lowest position.

2. Install the 4x objective into the nosepiece. Then in a

clock-wise direction, rotate the nosepiece and install

each succeeding higher magnification objective.

Inspect the objectives frequently for dirt or oil; clean

if necessary.

Use the 10X objective to initially focus the image of

yourspecimen.

When changing the objective magnification, rotate the

objective nosepiece until you hear a “click” sound.

This ensures the objective is centered in the optical

light path.

Installing the Glass Filter (Figure 7)

1. Swing out the condenser holder①

2. Insert the filter into the holder; swing the holder in.

Installing the Power Cord

(Figures 8-9-10)

★Do not bend or crush the power cord. This could

cause the cord to become unusable or dangerous.

1. Before connecting the power cord, make

sure the switch ①is in the “off” (O)

position.

2 Insert the female end of electrical cord plug

②into the socket ③.

3: Insert the male end of the power cord ④

into a surge suppressor receptacle ⑤.

★The microscope is factory set for either

110volts or 220volts.

Replacing the fuse (Figure 9)

Disconnect the power cord; ensure the

switch ①is “off”. Using a flat edge

screwdriver, remove the fuse holder ⑥,

insert new fuse, then insert the fuse holder

securely ⑦.

Figure 8

Figure 9

Figure 10

Figure 11

Figure 12

Installing & Changing the Halogen

Bulb（Figures 11, 12 & 13）

NOTE: Use only 6volt 20watt halogen

lamp.

1: Pull out & remove the condenser set ①.

1. Insert halogen lamp ①into the lamp

socket. NOTE: Do not touch the glass on

the bulb with your bare fingers. Handle

by using a soft cloth or tissue.

2. Changing the lamp during usage.

Ensure the power switch is off. Allow

time for all parts and the lamp are cooled

before handling.

Insert the lamp carefully; be sure the

pins on the bulb are completely inserted

into the lamp socket.

Attach the condenser set.

Figure 13

Altri manuali per 3002

Indice

Altri manuali Accu-Scope Microscopio

Accu-Scope

Accu-Scope 3055 Manuale utente

Accu-Scope

Accu-Scope 3078 Series Manuale utente

Accu-Scope

Accu-Scope EXC-100 Series Manuale utente

Accu-Scope

Accu-Scope EXI-310-PH Manuale utente

Accu-Scope

Accu-Scope 3019 Manuale utente

Accu-Scope

Accu-Scope 3000-LED series Manuale utente

Accu-Scope

Accu-Scope EXM-50 Manuale del proprietario

Accu-Scope

Accu-Scope 3078-HD Manuale utente

Accu-Scope

Accu-Scope 3075-GS Manuale utente

Accu-Scope

Accu-Scope 3075 SERIES Manuale utente

Accu-Scope

Accu-Scope EXI-410 Series Manuale utente

Accu-Scope

Accu-Scope 3088F Manuale utente

Accu-Scope

Accu-Scope EXS-210 Manuale utente

Accu-Scope

Accu-Scope Excelis HD Manuale utente

Accu-Scope

Accu-Scope EXI-600 Manuale utente

Accu-Scope

Accu-Scope 3078-HDR Manuale utente

Accu-Scope

Accu-Scope 3002-CB Forensic Comparison Series Manuale utente

Accu-Scope

Accu-Scope 3052-LED Manuale utente

Accu-Scope

Accu-Scope 3025 Manuale del proprietario

Accu-Scope

Accu-Scope 3025-LCD Manuale utente

Accu-Scope

Accu-Scope EXI-310 Series Manuale utente

Accu-Scope

Accu-Scope EXC-500 Manuale utente

Accu-Scope

Accu-Scope EXC-400 Series Manuale utente

Accu-Scope

Accu-Scope EXM-150-MS Manuale utente

Manuali Microscopio popolari di altre marche

Thermo Scientific

Thermo Scientific Nicolet iN10 Guida

National

National DC3-163 Manuale utente

KERN Optics

KERN Optics OPE-1 Manuale utente

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manuale utente

Prior

Prior Lux POL Manuale utente

Opitec

Opitec Smartscoop 115615 Manuale utente

KERN

KERN OPO-1 Manuale utente

Topcon

Topcon SP-1P Manuale utente

Motic

Motic PA43 Manuale utente

Leica

Leica DVM5000 Guida utente

MshOt

MshOt MZ62 Manuale utente

KERN Optics

KERN Optics OZR-5 Manuale utente

VWR

VWR VisiScope 384 Series Manuale utente

Nikon

Nikon ECLIPSE E200 POL Manuale utente

Leica

Leica DI C800 Manuale

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuale utente

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manuale utente

Olympus

Olympus SZ61 Manuale utente