Acer 930 Manuale
ChapterChapter
22
BIOS Utility
BIOS Utility 2-1
The BIOS Utility allows you to view your system’s configuration settings.
Most systems are already configured by the manufacturer or the dealer.
There is no need to run Setup when starting the computer unless you get a
Run Setup message.
The Setup program loads configuration values into the battery-backed
nonvolatile memory called CMOS RAM. This memory area is not part of
the system RAM. If you repeatedly receive Run Setup messages,
the battery may be bad. In this case, the system
cannot retain configuration values in CMOS.
Ask a qualified technician for assistance.
2-2User’s Guide
2.1 Entering Setup
To enter Setup, press the key combination ++.
You must press + + while the
system is booting. This key combination does not
work during any other time.
The BIOS Utility main menu then appears:
BIOS Utility
System Information
Product Information
Disk Drives
Power Management
Startup Configuration
Advanced Configuration
System Security
Date and Time
Load Default Settings
Abort Settings Change
↑↓←→ = Move highlight bar, ↵= Select, Esc = Exit
The parameters on the screens show default
values. These values may not be the same as
those in your system.
BIOS Utility 2-3
2.2 System Information
The following screen appears if you select System Information from the
main menu.
System Information Page 1/2
Processor ......................Pentium
Processor Speed ................xxx MHz
Bus Frequency ..................xx MHz
Internal Cache .................xx KB, Enabled
External Cache .................xxx KB, Enabled
Floppy Drive A .................x.xx MB, x.x-inch
Floppy Drive B .................None
IDE Primary Channel Master......Hard Disk
IDE Primary Channel Slave.......None
IDE Secondary Channel Master....CD-ROM
IDE Secondary Channel Slave.....None
Total Memory ...................xx MB
1st Bank .....................EDO
2nd Bank .....................EDO
3rd Bank .....................EDO
4th Bank .....................EDO
PgDn/PgUp = Move Screen, Esc = Back to Main Menu
The System Information menu shows the current basic configuration of your
system.
The command line at the bottom of the menu tells you how to move from
one screen to another and return to the main menu.
Press to move to the next page or to return to the previous page.
Press to return to the main menu.
2-4User’s Guide
The following screen shows page 2 of the System Information menu.
System Information Page 2/2
Serial Port 1 ..................... Disabled
Serial Port 2 ..................... 2F8h, IRQ 3
Parallel Port .................... 378h, IRQ 7
Pointing Device ................... Installed
Memory Parity Mode ................ Disabled
Onboard USB ....................... Disabled
PgDn/PgUp = Move Screen, Esc = Back to Main Menu
The following sections explain the parameters.
The parameters in the System Information
screens show default settings. These settings are
non-configurable from these screens.Select
other configuration options from the BIOS Utility
main menu to change the settings.
2.2.1 Processor
The Processor parameter specifies the type of processor currently installed in
your system. The system is designed to support the Intel Pentium II CPU.
2.2.2 Processor Speed
The Processor Speed parameter specifies the speed of the CPU currently
installed in your system. The system supports Intel Pentium II CPUs running
at 233, 266, or 300 MHz.
2.2.3 Bus Frequency
The Bus Frequency parameter specifies the system external clock. The bus
frequency can be either 60 or 66 MHz.
BIOS Utility 2-5
2.2.4 Internal Cache
This parameter specifies the first-level or the internal memory size (i.e., the
memory integrated into the CPU), and whether it is enabled or disabled. For
information on how to configure the system memory, see section 2.7.3.
2.2.5 External Cache
This parameter specifies the second-level cache memory size currently
supported by the system, and whether it is enabled or disabled. For
information on how to configure the system memory, see section 2.7.3.
2.2.6 Floppy Drive A
This parameter specifies the type of drive designated as Floppy Drive A. For
information on how to configure the floppy drives, see section 2.4.1.
2.2.7 Floppy Drive B
This parameter specifies the system’s current floppy drive B settings. For
information on how to configure the floppy drives, see section 2.4.1.
2.2.8 IDE Primary Channel Master
This parameter specifies the current configuration of the IDE device
connected to the master port of the primary IDE channel. For information on
how to configure IDE devices, see section 2.4.2.
2.2.9 IDE Primary Channel Slave
This parameter specifies the current configuration of the IDE device
connected to the slave port of the primary IDE channel. For information on
how to configure IDE devices, see section 2.4.2.
2.2.10 IDE Secondary Channel Master
This parameter specifies the current configuration of the IDE device
connected to the master port of the secondary IDE channel. For information
on how to configure IDE devices, see section 2.4.2.
2-6User’s Guide
2.2.11 IDE Secondary Channel Slave
This parameter specifies the current configuration of the IDE device
connected to the slave port of the secondary IDE channel. For information
on how to configure IDE devices, see section 2.4.2.
2.2.12 Total Memory
This parameter specifies the total system memory. The memory size is
automatically detected by BIOS during the POST. If you install additional
memory, the system automatically adjusts this parameter to display the new
memory size.
1st Bank
This parameter indicates the type of DRAM installed in bank 1. The None
setting indicates that there is no DRAM installed. For the location of bank
1, refer to Figure 1-2.
2nd Bank
This parameter indicates the type of DRAM installed in bank 2. The None
setting indicates that there is no DRAM installed. For the location of bank
2, refer to Figure 1-2.
3rd Bank
This parameter indicates the type of DRAM installed in bank 3. The None
setting indicates that there is no DRAM installed. For the location of bank
3, refer to Figure 1-2.
4th Bank
This parameter indicates the type of DRAM installed in bank 4. The None
setting indicates that there is no DRAM installed. For the location of bank
4, refer to Figure 1-2.
2.2.13 Serial Port 1
This parameter indicates the serial port 1 address and IRQ setting.
BIOS Utility 2-7
2.2.14 Serial Port 2
This parameter indicates the serial port 2 address and IRQ setting.
2.2.15 Parallel Port
This parameter indicates the parallel port address and IRQ setting.
2.2.16 Pointing Device
The BIOS utility automatically detects if there is a mouse connected to the
system. If there is, this parameter displays the Installed setting.
Otherwise, this is set to None.
2.2.17 Memory Parity Mode
This parameter indicates the setting of the memory parity mode. It may be
set to Enabled or Disabled .
2.2.18 Onboard USB
This parameter specifies whether the onboard USB controller is enabled or
not. For information on how to enable or disable USB, see section 2.7.1.
2-8User’s Guide
2.3 Product Information
The Product Information contains general data about the system. It includes
the product name, serial number, BIOS version, etc. These information are
necessary for troubleshooting and may be required when asking for technical
support.
The following screen shows the Product Information items.
Product Information Page 1/1
Product Name .......................... xxxxxxxxx
System S/N ............................ xxxxxxxxx
Main Board ID ......................... xxxxxxxxx
Main Board S/N ........................ xxxxxxxxx
System BIOS Version ................... vx.xx
System BIOS ID ........................ xxx.xx xxx-xx
BIOS Release Date ..................... xx/xx/xx
Esc = Back to Main Menu
2.3.1 Product Name
This parameter specifies the official name of the system.
2.3.2 System S/N
This parameter specifies the system’s serial number.
2.3.3 Main Board ID
This parameter specifies the system board’s identification number.
2.3.4 Main Board S/N
This parameter specifies the system board’s serial number.
2.3.5 System BIOS Version
This parameter specifies the version of the BIOS utility.
BIOS Utility 2-9
2.3.6 System BIOS ID
This parameter specifies the identification number of the BIOS utility.
2.3.7 BIOS Release Date
This parameter specifies the official date the BIOS version is released.
2-10 User’s Guide
2.4 Disk Drives
The Disk Drives menu lets you configure the system hard disk and disk
drive settings. If your hard disk supports the enhanced IDE features, you
may set the functions using this menu.
The following screen shows the Disk Drives parameters and their default
settings:
Disk Drives Page 1/1
Floppy Drive A ........... [xx-MB, xx-inch]
Floppy Drive B ........... [xx-MB, xx-inch]
8IDE Primary Channel Master
8IDE Primary Channel Slave
8IDE Secondary Channel Master
8IDE Secondary Channel Slave
↑↓ = Move Highlight Bar, →←= Change Setting, F1 = Help
The triangle mark that precede an item within a
menu indicates that there is a detailed menu for
that particular item. Select the item to display
the menu.
Altri manuali per 930
2
Indice
Altri manuali Acer Scheda madre
Acer
Acer V60N Istruzioni per l'installazione
Acer
Acer 486 Manuale utente
Acer
Acer V35X Manuale utente
Acer
Acer Extensa 900 Series Manuale utente
Acer
Acer Altos 1100 Series Manuale utente
Acer
Acer V65XA Manuale utente
Acer
Acer V70LA Manuale utente
Acer
Acer V12LC Manuale utente
Acer
Acer AcerPower 6500 Manuale utente
Acer
Acer 370LXA Manuale utente
Acer
Acer V62X Manuale utente
Acer
Acer Veriton 9100 Manuale utente
Acer
Acer Altos 9100 Series Manuale utente
Acer
Acer V59LT Istruzioni per l'installazione
Acer
Acer V65XA Istruzioni per l'installazione
Acer
Acer V70MA Manuale utente
Acer
Acer M9D Manuale utente
Acer
Acer Altos 21000 Series Manuale utente
Acer
Acer M1A Manuale utente
Acer
Acer M3A Manuale utente
Manuali Scheda madre popolari di altre marche
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuale utente
Gigabyte
Gigabyte GA-9IVDT Manuale utente
Texas Instruments
Texas Instruments ADS8372EVM Manuale utente
Commell
Commell MS-C73 Manuale utente
IBT Technologies
IBT Technologies MB860 Manuale utente
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuale utente
