Aclara Synergize RF Manuale utente
Synergize®RF Network
Intelligent Load Control (ILC) Device
Installation Instructions
Y99854-3-TUM
Revision B
www.Aclara.com
Synergize RF ILC Installation Instructions
Proprietary Notice
This document contains information that is private to Aclara Technologies LLC, an Ohio limited
liability company, and/or that is private to Aclara Meters LLC, a Delaware limited liability
company (individually or collectively “Aclara”). This information may not be published,
reproduced, or otherwise disseminated without the express written authorization of Aclara.
Any software or firmware described in this document is furnished under a license and may be
used or copied only in accordance with the terms of such license.
Disclaimer
The information in this document is subject to change without notice and should not be construed
as a commitment by Aclara. Aclara assumes no responsibility for any errors that may appear in
this document.
No responsibility is assumed for the use or reliability of software on equipment that is not
supplied by Aclara.
Metrum Cellular, STAR, Synergize, and TWACS are registered trademarks of Aclara
Technologies LLC.
Aclara Technologies LLC
Confidential and Proprietary
Copyright 2018-2019. All Rights Reserved.
Synergize RF ILC Installation Instructions 1
Warnings, Cautions, and Notes
Always consult and adhere to all local and national safety codes, regulations, and
standards.WARNING, CAUTION and Note statements are used throughout this
manual to emphasize important and critical information to help you ensure safety
and prevent product damage.These statements are defined below.
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious physical injury.
Indicates a situation, which, if not avoided, could result in damage to
equipment, damage to software, loss of data or invalid results.
N
OTE
Indicates important supplemental information.
FCC/IC Compliance
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving enclosure.
• Increase the separation between the equipment and receiver.
• Connect the equipment to a circuit different from that to which the receiver is
connected.
• Contact Aclara for help.
Any changes or modification made to this device without the expressed,
written approval of Aclara Technologies LLC may void the user's authority to
operate this device.
2Synergize RF ILC Installation Instructions
FCC/IC Compliance
Antennas
Only the antenna provided with this device is authorized to be used without
additional approvals from Aclara, the FCC, and ISED.
FCC/IC RF Exposure Guide
Aclara Technologies LLC low power RF devices and their antennas must be
fixed-mounted on outdoor permanent structures providing a separation distance of
at least 20 cm from all persons during normal operation. This device is not
designed to operate in conjunction with any other antennas or transmitters. No
other operating instructions for satisfying RF exposure compliance are needed.
Rated Output Power
Field Calibration Procedure
Aclara Technologies LLC low power RF devices have passed through extensive
testing and calibration procedures while in the factory. Therefore, no additional
calibration or adjustment is required in the field.
Conducted Power Radiated Power with
Max Gain Antenna*
Standard Range 29.5 dBm +/- 1dB 29.5 dBm EIRP
0.8913 W average 0.8913 W average
*Max antenna gain = 0 dBi
Synergize RF ILC Installation Instructions 3
Avertissements, mises en garde et remarques
Toujours consulter et respecter les codes, règlements et normes de sécurité locaux
et nationaux. Des AVERTISSEMENTS, MISES EN GARDE et remarques sont
utilisés tout au long de ce guide pour souligner l'information importante et critique
qui vous aidera à assurer la sécurité et à prévenir les dommages au produit. Ces
énoncés sont définis ci-dessous.
A
VERTISSEMENT
indique une situation potentiellement dangereuse qui, si elle n'était pas évitée,
pourrait entraîner la mort ou des blessures graves.
M
ISE
E
N
G
ARDE
indique une situation qui, si elle n'était pas évitée, pourrait entraîner des
dommages à l'équipement, des dommages au logiciel, des pertes de données ou
des résultats invalides.
R
EMARQUE
indique des informations supplémentaires importantes.
Conformité FCC/IC
Cet équipement a été testé et il est conforme aux limites pour un appareil
numérique de Classe B, en vertu de l'article 15 des règlements de la FCC. Ces
limites sont conçues pour offrir une protection raisonnable contre l'interférence
nuisible dans une installation résidentielle. Cet équipement génère, utilise et peut
émettre de l'énergie de fréquences radio et, s'il n'est pas installé ou utilisé
conformément aux instructions, il peut causer une interférence nuisible aux
communications radio. Il n'existe toutefois aucune garantie que de telles
interférences ne se produiront pas dans une installation particulière. Si cet appareil
cause des interférences nuisibles à la réception des signaux de radio ou de
télévision, ce qui peut être détecté en mettant l'appareil sous et hors tension,
l'utilisateur peut tenter de neutraliser l'interférence de l'une ou l'autre des façons
suivantes :
• Réorienter ou repositionner l'antenne de réception.
• Augmenter la distance séparant l'équipement du récepteur.
• Brancher l'appareil dans une prise sur un circuit électrique différent de celui
sur lequel le récepteur est branché.
• Consulter le fournisseur ou un technicien radio ou télévision expérimenté.
MISE EN
GARDE Tout changement ou toute modification à cet appareil sans l'approbation
écrite expresse d'Aclara Technologies LLC peut annuler l'autorisation de
l'utilisateur d'utiliser cet appareil.
4Synergize RF ILC Installation Instructions
Conformité FCC/IC
Antennes
L'antenne fournie avec ce compteur est la seule qui puisse être utilisé sans
l'approbation d' Aclara, the FCC et l' ISED.
Guide d'exposition aux RF FCC/IC
Les appareils RF à faible puissance Aclara Technologies LLC ainsi que leurs
antennes doivent être montés de manière fixe sur des structures intérieures ou
extérieures permanentes qui se trouvent à au moins 20 cm des personnes pendant
le fonctionnement normal. Cet appareil n'est pas conçu (et il n'a aucun
branchement externe) pour être utilisé en association avec toute autre antenne ou
tout transmetteur. Aucune autre instruction d'utilisation n'est requise pour assurer
la conformité aux règles d'exposition aux RF.
Puissance de Sortie Nominale
Procédure de calibration sur place
Les appareils RF à faible puissance Aclara Technologies LLC ont été soumis à des
tests étendus et multi-tâches et à des procédures de calibration complexes en usine.
Par conséquent, ils ne requièrent pas de calibration ni d'ajustement supplémentaire
sur place.
Puissance Conduite Puissance Rayonnée Avec
Antenne à Gain Maximum*
Gamme Standard
29.5 dBm +/- 1dB 29.5 dBm +/- 1dB
Puissance Isotrope Rayonnée
Equivalente
0.8913 W moyenne 0.8913 W moyenne
*Gain d’antenne maximal = 0 dBi
Synergize RF ILC Installation Instructions 5
Installation Notes
Relay Connection
The ILC device 24 VAC relay port is only designed to accept a maximum 5 A.
This limit applies even if the relay component supports 12 A. 24 VAC/5 A port
loads must be protected with dedicated 5 A breakers. 208-277 VAC/30 A port
loads must be protected with dedicated 30 A breakers.
RF Location
The ILC device contains an internal radio antenna intended only for outdoor
use. Install the ILC device in an area where structures, trees, or hills provide
minimum obstructions. Refer to MTU Installation Requirements (Y20255-TEB)
for additional information.
Power Source
The ILC device must be sourced from a dedicated 5 amp breaker.
Introduction
Use these instructions in conjunction with
standard utility safety guidelines and
procedures when installing Aclara’s
Intelligent Load Control (ILC) device.
Utility supplied high voltage field wiring
must use copper conductor only and have a
+90° C rating. All field wiring should
comply with local and national codes.
To ensure a rainproof seal, make sure that
the door is completely closed and screw is
fully seated. It is the installer and utility's
responsibility to ensure the door is secured
with an anti-tamper seal or lock.
6Synergize RF ILC Installation Instructions
Safety Warning
Safety Warning
Any work near high voltage can present a danger of electrical shock. Your
personal safety may be compromised if Aclara equipment is used in a manner
not specified by Aclara. All wiring must be installed in accordance with local
and national codes.
Required Tools
In addition to standard hand tools, the following special tools are required to
perform this procedure:
• 0-10 in-lbs. torque-limiting screwdriver
Installation Instructions
N
OTES
Only copper conductors should be used. Wire gauge is load dependent for
relays, and Aclara specifies a range of 30 to 10 AWG, with the maximum size
being 10 gauge for relay terminals. Minimum wire gauge should be determined
by the particular relay, the National Electric Code (NEC), and local standards.
AclaraONE version 1.4 or greater is required for full Intelligent Load Control
functionality.
The following procedure describes how to install an ILC device.
1. Using the appropriate hardware for the mounting surface, secure the ILC
device at the desired location by the three mounting tabs.
Indice
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
