Ad Notam DSTB-T Manuale utente

DIGITAL SET TOP BOX, DVB-T/S2 USER MANUAL

subject to modiﬁ cation * 06-2013 * V1

SUMMARY

General Information 04

Installation Wet Rooms 10

Product Information 11

Getting Started 13

Troubleshooting 23

Technical Speciﬁ cation 24

DSTB-T/S2

GENERAL INFORMATION - SAFETY

CAUTION

• Only qualiﬁ ed specialist staff may carry out service tasks. Service work is necessary, if the unit has been damaged,

e.g. if the mains plug or mains cable have been damaged, if liquid or items are present inside the device, if it has

been exposed to water or moisture, if it does not work properly or if it has fallen down.

• Never remove the casing covers or modify the product in any way. This can cause an electric shock or burn you.

• Immediately pull the plug, if you notice that your product emits smoke, smells burnt or emits unusual noises and

ask your specialist dealer for advice.

• Do not allow the product to come into contact with liquids. Liquid in the casing can cause a ﬁ re, electric shock or

damage the device. Immediately pull the mains plug out, if an item or liquid gets into the casing. Notice that the

apparatus shall not be exposed to splashing or dripping liquids and no objects ﬁ lled with liquids, such as vases,

shall be placed on the apparatus.

• Keep small items away from the product. These can fall into the casing and cause a fire, an electric shock or

damage the device. Don‘t try to reach into the housing or plugs with wires or the like.

• Never touch not-isolated parts of the plug, if the device is connected to the power adapter!

• Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall

remain readily operable.

• Avoid any impact and do not allow the product to fall!

GENERAL INFORMATION - INSTALLATION

Operation and Storage Requirements

The ambient temperature for operating the device is between +5 and +50 degrees Celsius. Do not install the device

in the proximity of heat sources, such as heating pipes, heaters, furnaces or other devices, which radiate heat.

Mount the device in such a way that it is protected against moisture. Trouble free operation is ensured up to 75% air

humidity.To prevent ﬁ re or electric shock, never allow liquids to enter the unit. The product must be stored in dry and

well-ventilated rooms, without extreme temperature ﬂ uctuations. Heat sources and aggressive active substances may

not be stored in the proximity of the device. The required storage temperature is 0°C - +60°C at an air humidity of

5 - 85% RH. The device must be stored in the complete packaging, as delivered.

Installation

Have this product installed by qualiﬁ ed staff only. Use the mounting systems which are speciﬁ ed or recommended

by ad notam. Install the product in a way that it is ﬁ xed properly and take care that children are not exposed to dan-

ger. Please take extra care during installation, avoid impacts. Before cabling your device, check that the power is off.

To avoid any possibility of electric shock, always connect your equipment to properly earthed outlets. Use of power

cords or adapters other than those provided may cause ﬁ re or malfunction. Place this product as close to the power

socket as possible. Leave enough space to insert and remove the power plug on demand. Even if you switch off the

product with your remote control, power is not cut off unless the power cord is unplugged.

Installation Environment

Avoid direct light or sun exposure, direct proximity to heat sources, outdoor installation. The product is speciﬁ cally

designed for indoor use only. There is the danger of ﬁ re and of electric shocks and damage to the device, if it is

operated outdoors. Do not place any heat sources such as radiators and heat registers, etc. near the device.

DSTB-T/S2

Installation of Power Adapters

The device may only be operated with the provided power adapter. The rated voltage is indicated on the product

label. The device is factory-set to the optimal operating voltage (see Technical Speciﬁ cation). Use only power cords

and plugs that are suitable for your local electrical outlets. Install the power cords in such a way that it does not

obstruct anyone. Ensure furthermore that the cable is not clamped and that it cannot be pulled out accidentally from

the power adapter. Do not install the power cords in the proximity of heating elements and never place heavy items

on the cable or power adapter. Do not modify or arbitrary repair the power cords.

CAUTION

Do not use any power cords or adapters other than those provided with this product! Use of power cords or

adapters other than those provided with this product may cause ﬁ re, electric shock or malfunction. If several kinds

of power cords are provided with this product, use the one that ﬁ ts your power socket. Do not let the adapter hang

down while using. Do not cover or wrap the adapter. Leave space around the adapter to prevent overheating. The

individual components can be destroyed, if the polarity is reversed or an incorrect connection is used.

A goodwill replacement is not possible in such cases, since each device is submitted to meticulous quality

inspections prior to shipping. The connecting plugs must be attached in such a way that the connector is held ﬁ rmly.

Have trained technical personnel install the electrical facilities necessary for mounting. The power adapter has to be

installed in ventilated areas due to the heat emission! Connect the power cord to a grounding outlet! Never cut or

damage the power cord!

Please disconnect the device from the power adapter in the following cases:

• The device is out of use for a lengthy period.

• The device malfunctions or displays other unusual features, necessitating maintenance work.

• During a thunderstorm.

Please plan the positioning of the power adapter and the source cables before proceeding with the structural

measures and positioning of the device. Observe the protection zones when placing the power adapter! For

in-wall applications please bear in mind that the power adapter has to be placed beyond the inset due to heat

emission!

NOTE

The power adapter should be adequately secured to prevent it from becoming unstable and/or falling. Make sure the

power source circuits are properly grounded. Use the supplied power cord in order to connect it to the power source. If your

installation requires a different power cord, be sure to use an ofﬁ cially approved power cord displaying the mark of the

safety agency that deﬁ nes the regulations for power cords in your country. Please consider that the AC outlet for the power

adapter is placed within reach and should be easily accessible in case it needs to be powered off.

Do install the product in a dry environment where the operating ambient temperature might not exceed 40°C / 104°F.

Also don´t position the power adapter on top or on the back of the device in order to prevent thermal overload.

Ensure

that your installation complies with your national safety rules. Any servicing, adjustment, maintenance or repair must

be performed only by service-trained personnel.

Ensure that the power adapter is installed in a serviceable location, to access it easily in case of a defect. If you choose

to place the power adapter in a separate space, take care that the ventilation is present, because the power adapters

need convection cooling for stable working conditions.

When placing the power adapter in a fully enclosed space, make sure the air ﬂ ow around the sides and top of the power

adapter is not restricted. According to a common rule of thumb the minimum dimensions for a niche for the power

adapter may be deﬁ ned as follows: please calculate the length of the power adapter plus an additional gap of at least

100mm all around for DC 12V power adapters.

DSTB-T/S2

GENERAL INFORMATION - TRADEMARK

ad notam®, MIRROR IMAGE®, MAGIC MIRROR®

AD NOTAM, MIRROR IMAGE and MAGIC MIRROR are trademarks of the ad notam group.

HDMITM

HDMI, HDMI CEC (HDMI Consumer Electronics Control), the HDMI logo and HIGH-DEFINITION MULTIMEDIA

INTERFACE are trademarks of HDMI Licensing LLC.

GENERAL INFORMATION - DISPOSAL OF OLD EQUIPMENT AND BATTERIES

European Union

The following symbol indicates that electrical resp. electronic equipment and batteries signed with this symbol

should not be disposed of as general household waste at its end of life. Instead, the products should be handed over

to the applicable collection points for the recycling of electrical and electronic equipment as well as batteries for

proper treatment, recovery and recycling in accordance with your national legislation and the Directive 2002/96/EC

and 2006/66/EC.

By disposing of the products correctly, you will help to conserve natural resources and will help to prevent potential

negative effects on the environment and human health which could otherwise be caused by inappropriate waste

handling of these products. For more information about collection points and recycling of these products, please

contact your local municipal office or your household waste disposal service. Penalties may be applicable for

incorrect disposal of this waste, in accordance with national legislation.

Other Countries outside the European Union

These symbols are only valid within the European Union. If you wish to dispose of these items outside the European

Union, please do so in accordance with the applicable national legislation or other rules of your country for the

treatment of old electrical and electronic equipment and batteries.

NOTICE: An appendix "Pb" below this symbol indicates that the battery contains lead.

DSTB-T/S2

INSTALLATION IN WET ROOMS

For installations in wet rooms speciﬁ c installation guidelines apply, which are to be seen in the context of placing the

power adapter outside of certain protection zones. These regulations differ by region. Please contact a specialist for

this. In Germany electrical installations are to be performed by a skilled technician, while observing the regulations of

the standard DIN VDE 0100 T.701.

According to this standard, ad notam monitor systems with DC 12V (Limited Power Source Class II, SELV) can be

installed at each position (incl. Zones “0” and “1”) in harsh environments, also in showers and above a bath tub as

long as the low voltage product is shielded from a sealed glass surface and the (external) power adapter is installed

beyond these protection zones.

NOTE

The safety current source has to be arranged outside the zones 0 - 2 and needs to be protected against direct

impact. The assessment of the protection zones on site of the installation must be performed in accordance with the

valid national guidelines by a skilled local electrician. ad notam will not be held liable for improper installation!

Zone Class Requirements

0 IP x6-8 waterproof, max. 12V,

only SELV qualiﬁ ed electronic devices

1 IP x5

hose waterproof, max. 50V,

only stationary electronic devices

(IP x5 or qualiﬁ ed SELV)

2 IP x4

splashproof,

only stationary electronic devices

(IP x4 or qualiﬁ ed SELV)

3 IP x0-3 devices with at least protection against

dripping water recommended

600

2250

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ad Notam Decoder

Ad Notam

Ad Notam DSTB-IPTV Manuale utente

Manuali Decoder popolari di altre marche

VBrick

VBrick 8000-0188 Manuale utente

Kogan

Kogan KGNPVR500VAA Manuale utente

Asus

Asus O!PLAY MEDIA PRO Manuale utente

Samsung

Samsung ICU 100 Manuale utente

VECTORMAX

VECTORMAX A12E Manuale utente

DStv

DStv Explora Manuale utente

Ace Digital TV

Ace Digital TV ADB 3800 Manuale utente

Cisco

Cisco 4398DVB Manuale utente

Polaroid

Polaroid KHA-01651B Manuale utente

Samsung

Samsung GX-SM530CF Manuale utente

BT Business Total Broadband Manuale utente

Megasat

Megasat HD 720 plus Manuale utente

Sungale

Sungale STB608 Manuale utente

Amino

Amino Amigo 7X Manuale utente

Geniatech

Geniatech ATV225 Manuale utente

Android

Android Androidminibox mx2 se Manuale utente

Hama

Hama Internet TV Box Manuale utente

Ariva

Ariva T650i Manuale utente