Addonics Technologies DCDCS256S Manuale utente

Addonics

T E C H N O L O G I E S

Diamond Cipher AES 256-bit Drive Cartridge System

Model: DCDCS256S & DCDCS256U

User’s Guide

FCC Warning Statement

This equipment has been tested and found to comply with the limits for a class B digital

device pursuant to Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy. If not installed and

used in accordance with the instructions, it may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If the equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment on and off, the user

is encouraged to try and correct the interference by one or more of the following

suggestions.

Reorient or relocate the receiving antenna

Increase the distance between the equipment and the receiver

Connect the equipment to a different power outlet other than the one where receiver is

connected

Consult a certified television or radio technician

Enclosure and Drive Cradle Overview

The drive enclosure is the enclosure where a SATA hard drive is mounted and

secured by 4 screws.

Drive cradle, also known as fixed tray, is the frame that mounts inside the drive

bay of a desktop, server or any computing equipment. The drive cradle provides

both power and data connection between the computer and the drive enclosure.

The Diamond cipher drive cradle fits into any standard 5 ¼” drive bay and can

connect to the computer via SATA or USB 2.0. This interface allows hot

swapping the hard drive without restarting or rebooting the system. The Diamond

drive cradle is compatible with all Diamond drive enclosures and Diamond cipher

drive enclosures. As a result you can insert SATA or IDE hard drive, encrypted or

unencrypted, into the same drive cradle of a computer.

Cipher Key Socket

Handle

Encryption key

active LED

Cipher Key

Power Switch /

Locking Mechanism

Power LED

Drive Activity

LED

Drive Cradle

Drive

Enclosure

Diamond Cipher key

Check to make sure you have the correct version of the Diamond Cipher key.

The key should match the label at the back

of the drive enclosure.

Black label AES-256 stands for Diamond

Cipher 256-bit key

IMPORTANT

There is no back door for the Diamond Cipher encrypted hard drive if the

key is lost or stolen.

To ensure there is a spare key, your Diamond Cipher bundled kit comes with one

pair of Diamond Cipher keys. These 2 keys have identical encryption code. One

of these keys should be kept in a safe and secure location and can be sent back

to Addonics for duplicating additional keys. If you are down to the last key, be

sure to make a back up of all the data stored inside your encrypted hard drive

prior to sending the last key to Addonics. Addonics is not responsible for key lost

in the mail or retrieval of the data inside the encrypted hard drive.

The CIPHER key MUST be inserted at the front of the drive enclosure in

order for the drive to be ACTIVATED.

Once the drive is INITIALIZED using the Cipher Key that comes with the kit,

the drive can only be accessed by the original key.

The 2 keys that come with each Diamond Cipher bundled kit has their own

unique encryption code. So the keys among different kits are not

interchangeable.

If you have multiple sets of Diamond Cipher kits and would like all the keys

to have the same encryption code, you may make this request at the time of

your order or mail the keys together with master key back to Addonics to

recode them for you. Again be sure that you keep a spare key with you.

Make a back up of your data if you are mailing in your last key.

Keeping track of the hard drive

If you are using the Diamond Cipher drive enclosure to encrypt multiple hard

drives, it is important to label your hard drive if you are taking the drive out of the

enclosure. The hard drive with Diamond Cipher encryption will look like a brand

new drive when attach directly to the SATA controller of a computer. There will

be no partition or any hint to indicate that the drive contains encrypted data.

When the drive is partitioned, all the encrypted data will be lost.

The same holds true if a hard drive already has data on it is installed into the

Diamond Cipher drive enclosure. The computer detects the hard drive as a brand

new drive or a drive that is unallocated. Once you proceed to partition the drive,

the data that was on the hard drive will be erased and cannot be recovered.

A Diamond Cipher encrypted hard drive can be moved to another Diamond

Cipher drive enclosure. But the same key used in encrypting the hard drive must

be used in the new drive enclosure in order to access the drive.

If you are installing multiple Diamond Cipher drive kits in your

organization, it is important to keep track of the drive and the encryption

key. Once it gets mixed up, there is no possible way to recover the data on

the encrypted hard drive.

Hard Drive Installation Guide

Step 1

Use a Philips screwdriver to

turn the cover securing screw

into the “OPEN” position.

Step 2

Slide the aluminum cover

towards the back end of the

Diamond and remove it.

Step 3

Carefully place the SATA hard drive

with the label facing up into the

Diamond enclosure. Push the hard

drive towards the back end to secure

the drive connectors onto the

Diamond enclosure’s SATA

connector.

Step 4

Turn the Diamond enclosure over with

the hard drive mounting holes facing

up. Use the included flat head screws

to secure the hard drive onto the

bottom of the enclosure and turn in

the screw to the “LOCK” position.

Powering On the Drive Cartridge System:

Note: Be sure the Diamond cipher key is inserted into the drive enclosure prior

to turning on the power of the drive cradle. The hard drive will not be

detected by the computer if the power to the drive cradle is turned on

without the Cipher key. Under such condition, the power on the drive

cradle will have to be turned off and turned back on again with the

Cipher key already inserted into the drive enclosure in order to detect

the hard drive.

Power Switch:

To power on the enclosure, use the key provided to turn the locking mechanism

on the drive cradle into the Lock position. When the switch is turned on, the

green LED located on the left side of the drive cradle would light up to indicate

power. The encryption key LED will also light up. The amber LED will blink if

there is drive activity.

Note: There are no drivers needed to use the eSATA cable as long as the

drivers are installed for the Serial ATA Controller card/chip. It is plug

and play.

Brand new hard drive must be partitioned and formatted first before a

drive letter is assigned by the OS. When a hard drive with data on it is

formatted with the Diamond cipher all the data will be erased.

Once the drive is detected by the system OS, the Diamond cipher key

may be removed from the drive enclosure. The encryption key LED will

turn off but the Diamond Cipher hard drive will continue operating

normally (encrypting) till it is removed from the system or powered off.

Cable Connections

Model: DCDCS256S

Power: Use either the 4-pin Molex or the 15-pin SATA power connector.

Do not use both power sources simultaneously.

Data:

Connect the SATA cable to the SATA connector located at the back of the drive

cradle and the other end to the SATA connector on your SATA host controller or

onboard SATA port.

LED cable: Only needed if you want to get drive access signal from the SATA

controller. Use the LED cable to connect the LED pin located at the back of the

cradle (beside the LED switch) to the LED jumper pins on your SATA host

controller or onboard SATA port to enable the drive activity LED.

Factory default, LED signal coming from hard drive.

Model: DCDCS256U

Power: Using the 4-pin floppy connector of the Y-cable, connect it to the floppy-

type power connector on the converter. To provide power for the y-cable,

connect it to one of your desktop's 4-pin molex cable.

Data:

Internal Connection

Use the USB 5-pin header cable to connect to the 5-pin connection on the

converter located below the USB Type B connector to the 5-pin USB connection

on your motherboard.

External Connection

Use the USB Type A-B data cable to connect the converter to the USB port on

your system.

LED cable: Only needed if you want to get drive access signal from the SATA to

USB2.0 converter. Use the LED cable to connect the LED pin located at the back

of the cradle (beside the LED switch) to the LED jumper pins on the SATA to

USB2.0 converter to enable the drive activity LED.

Factory default, LED signal coming from hard drive.

Technical Support

If you need assistance to get your unit functioning properly, please call Addonics

Technical Support. Our technical staff will be happy to assist you, but they will

need your help to do so. Calling the technical support staff without all the proper

information can be both time consuming and frustrating. Here are some tips to

help you out:

MODEL NUMBER –Please have this number on hand.

SYSTEM INFORMATION –Type of computer, peripherals, etc.

OPERATING SYSTEM –What version of Windows

WHAT’S THE TROUBLE? – Give enough information

about your problem so that we can recreate and diagnose it.

FREE Software Drivers for all Addonics Technologies

Products are available 24 hours per day at the

World Wide Web Site: www.addonics.com

Contact Information

Phone: 408-573-8580

Fax: 408-573-8588

Email: http://www.addonics.com/sales/query/

Internet: http://www.addonics.com

TECHNICAL SUPPORT

Phone: 408-453-6212

Hours: 8:30 am - 6:00 pm PST

Email: http://www.addonics.com/support/query/

Questo manuale è adatto per i seguenti modelli

Altri manuali Addonics Technologies Magazzinaggio

Addonics Technologies

Addonics Technologies PPROEPU3 Manuale utente

Addonics Technologies

Addonics Technologies RT3DAHEU3 Manuale utente

Addonics Technologies

Addonics Technologies RCED256ES Manuale utente

Addonics Technologies

Addonics Technologies NA3MS4HU2B Manuale utente

Addonics Technologies

Addonics Technologies ST45HPMXA-B Manuale utente

Addonics Technologies

Addonics Technologies Sapphire Combo SBDRHEU Manuale utente

Addonics Technologies

Addonics Technologies Combo Hard Drive25 IDE Manuale utente

Addonics Technologies

Addonics Technologies REDESP? REDESPU3 Manuale utente

Addonics Technologies

Addonics Technologies RCHD256ES Manuale utente

Addonics Technologies

Addonics Technologies AD25CFD Manuale utente

Addonics Technologies

Addonics Technologies External CipherChain Manuale utente

Addonics Technologies

Addonics Technologies RT134SDEU3 Manuale utente

Addonics Technologies

Addonics Technologies DGC3 Manuale utente

Addonics Technologies

Addonics Technologies RAID TOWER IX RT93DAHX Manuale utente

Addonics Technologies

Addonics Technologies NAS NAST4SR5HPM-B Manuale utente

Addonics Technologies

Addonics Technologies ST55HPMXU Manuale utente

Addonics Technologies

Addonics Technologies AD25MSD Manuale utente

Addonics Technologies

Addonics Technologies RCHDSAES Manuale utente

Addonics Technologies

Addonics Technologies RT54S2HMEU Manuale utente

Addonics Technologies

Addonics Technologies AD25CFASTD Manuale utente

Addonics Technologies

Addonics Technologies ST13 Manuale utente

Addonics Technologies

Addonics Technologies Sapphire Mobile Rack II Manuale utente

Addonics Technologies

Addonics Technologies Sapphire Cipher II Snap-In SSN6G-256EU Manuale utente

Addonics Technologies

Addonics Technologies AESNAPMRI Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente