ADITIVA 3D VORON BELT 350 KIT Manuale utente
Voron 2.4 Conveyor 90 Belt Kit assembly manual P a g e 2 | 27
www.belt3dprinterkit.com
Content
Chapter 1 Intro 3
Step 1.1 What is included in this kit? 3
Step 1.2 Needed tools 3
Chapter 2 Disassembling Voron 2.4 front doors and heatbed 3
Step 2.1 Removing front door parts 4
Step 2.2 Removing Heatbed 4
Chapter 3 Preparing frame 5
Step 3.1 Installing bottom plates 5
Chapter 4 Installing Belt and Heatbed system 10
Step 4.1 Preparing rollers 10
Step 4.2 Installing Rollers and Belt 11
Step 4.3 Mounting Heatbed 16
Chapter 5 Finishing installation 18
Step 5.1 Belt holders mounting 18
Step 5.2 Face plate mounting 19
Step 5.3 Installing front STRIP CURTAIN 19
Chapter 6 Klipper and firmware settings 21
Voron 2.4 Conveyor 90 Belt Kit assembly manual P a g e 3 | 27
www.belt3dprinterkit.com
Chapter 1 Intro
Step 1.1 What is included in this kit?
In this kit you will find all the necessary parts for converting your regular Voron 2.4 3d printer
into a sequential Conveyor 3d printer. Parts lists are indicated on each step for better
understanding and guidance.
Step 1.2 Needed tools
In order to fully install this kit, you will need the next tools:
Set of Allen keys
Adjustable wrench or wrench kit
Measuring tape
Vernier caliper
Metal ruler (for alignment)
Chapter 2 Disassembling Voron 2.4 front doors and heatbed
In order to get ready to install this kit, you have to disassembly various segments of the original
3d printer, this part will guide you through entire process of preparation and getting ready to
install new parts.
*Please be aware some original parts will be discarded and won’t be installed.
Figure 1. Assembled Heatbed
Voron 2.4 Conveyor 90 Belt Kit assembly manual P a g e 4 | 27
www.belt3dprinterkit.com
Step 2.1 Removing front door parts
Remove all brackets, panels and hinges from both front doors.
Figure 2 remove highlighted parts
Step 2.2 Removing Heatbed
Before starting to remove the heatbed, we need to secure both DIN rails that holds all
the electronic components, so we flip the printer carefully and remove the bottom
panel.
After that, we use the printed BRACKET_DIN_RAIL_X4.STL part and secure the DIN rails
using 4 units M4x8 screws and 2 units T-nuts on each bracket as shown in the next
picture.
Figure 3 Securing DIN rails before removing heatbed bars
Voron 2.4 Conveyor 90 Belt Kit assembly manual P a g e 5 | 27
www.belt3dprinterkit.com
We remove heating bed at this point, by releasing 4 units M3 bolts that holds it down,
it is highly recommended to remove any magnetic base plate, and clean the aluminum
heatbed with IPA in order to remove any glue from it:
*Note: Do not disconnect the heatbed from the electronics, just keep it loose for next
steps.
Figure 4 Removing heatbed screws
Now we can securely remove both 2020 aluminum bars that holds the heatbed, by
removing the 4 screws on each side, you have to disconnect cable from the Z endstop
unit, since it won’t be used:
Figure 5 Removing heatbed support bars
Chapter 3 Preparing frame
We are pretty much ready to install our kit.
Step 3.1 Installing bottom plates
Let’s identify each bracket part first:
Voron 2.4 Conveyor 90 Belt Kit assembly manual P a g e 7 | 27
www.belt3dprinterkit.com
Figure 9: P4 VC90 CNC FRONT RIGHT BRACKET
Next items from the KIT will be used:
ITEM
ITEM DESCRIPTION
Quantity
Type
1
P1 VC90 BACK LEFT BRACKET
1
Kit
2
P2 VC90 BACK RIGHT BRACKET
1
Kit
3
P3 VC90 CNC FRONT LEFT
BRACKET
1
Kit
4
P4 VC90 CNC FRONT RIGHT
BRACKET
1
Kit
5
M5 x 20 mm Screw
2
Kit
6
M5 x 50 mm Screw
2
Kit
7
M5 T-Slot nut
4
Kit
8
M4 x 8 mm Screw
5
Kit
9
M4 T-Slot nut
5
Kit
Install 2 CNC bracket plates as shown in the next picture, M5 screws and M5 T-slot nuts
will be used, left and right sides must be assembled:
Voron 2.4 Conveyor 90 Belt Kit assembly manual P a g e 8 | 27
www.belt3dprinterkit.com
Figure 10 Installing front CNC brackets on each corner of bottom frame
Install 2 back bracket plates as shown in the next picture, M4x8 screws and M4 T-slot
nuts will be used, left and right sides must be assembled, they have to be installed right
next to the timing belt cover:
Note: If necessary and for easier mounting, is highly recommend to remove side panels
to reach those brackets and other parts from the conveyor system
1 M5x20 SCREW +
1 M5 T-SLOT NUT
1 M5x50 SCREW +
1 M5 T-SLOT NUT
Voron 2.4 Conveyor 90 Belt Kit assembly manual P a g e 10 | 27
www.belt3dprinterkit.com
Chapter 4 Installing Belt and Heatbed system
Figure 13 Belt system Assembly
Step 4.1 Preparing rollers
Next items from the KIT will be used:
ITEM
ITEM DESCRIPTION
Quantity
Type
1
Roller BODY 40 mm
2
Kit
2
12 mm ROD
2
Kit
3
Roller Cap 46mm
4
Kit
4
M4x8mm Black Headless screw
8
Kit
Using all the mentioned parts, proceed to assemble them in the next order, first place
12mm ROD inside Rolle BODY 40mm, then insert Roller CAP 46mm on each end, making
sure it all fits very tight, keep in mind that 12mm ROD have to be placed according to
the next pictures. Finally using an allen key, proceed to secure both ROLLE CAP 46mm
with the M4x8mm BLACK HEADLESS SCREWS (02 on each side):
*Note: You have to repeat this process in order to get 2 rollers assembly.
Indice
Altri manuali ADITIVA 3D Stampante 3D
