ADTRAN SMART/RG SR516ac Manuale utente

SR516ac

Quick Start Guide

Installation

1. Connect one end of the included phone cable to the DSL port on the gateway and connect the other end to the

wall jack.

2. Connect one end of an Ethernet cable to a LAN port of the gateway and connect the other end to your PC.

3. Plug the power adapter into the wall outlet and connect the other end of it to the Power port of the gateway.

4. Turn on the unit by pressing the On/Off button on the left side of the gateway.

Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to

complete before you can begin using your Internet applications (browser, email, etc.).

Notes:

lIf you use 3G WAN service, connect the 3G USB data card to the USB port of the gateway. If you use the Ethernet

uplink, connect to the WAN port with an Ethernet cable.

lYou cannot use the xDSL uplink, 3G WAN service, and Ethernet uplink at the same time.

If you are unable to connect to the Internet, confirm that all connections are in place and the gateway is turned on.

LED Indicators

The LEDs on the front of the SR516ac gateway can help you

understand the current state of your adapter.

Legend: White White blinking Red Green Green blinking

LED Action Explanation

All LEDs

except

those

listed below

Feature enabled &/or working correctly

Data being transferred

POWER Device in CFE mode

Device powered on and ready for use

WAN WAN connection active

LAN LAN connection active

Data being transferred

Quick Gateway Configuration

Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small

round hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into

the hole, press the button for 1 second, and then release the button. The system reboots and returns to the factory

defaults.

Logging in to your gateway

To change the settings on your gateway, you must log in to the gateway's interface. Make sure that you have completed

the steps in "Installation" before you begin.

1. Open your internet browser application and type 192.168.1.1 into the address line. The login dialog appears.

2. Enter the factory default credentials shown below and click OK.

User Name: admin Password: admin

Note: Your service provider may use other settings. Contact your provider for details.

Configuring the WAN manually

If the automatic connect process is unsuccessful, refer to the Advanced Setup >Layer 2 Interface and WAN Service

sections of the SmartRG SR516ac Gateway User Manual to manually establish a connection.

WiFi Setup

Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow

the instructions for the applicable method. The default settings work for most situations.

1. In the left menu, click Wireless and then click 2.4 GHz Band or 5 GHz Band. The fields are the same for both

options. The wireless radio is enabled by default.

2. If desired, in the SSID field, enter the network name to which you want your client devices connected.

Continue with the steps in the method you prefer.

3. Continue with the steps for the method you prefer.

WPS Method

If the device you wish to connect to the Internet via your gateway supports the WPS secure Wi-Fi connection method,

follow these steps.

1. In the left navigation bar, click Wireless, click the band that you want to configure, and then click Security.

2. In the Enable WPS field, make sure that Enabled is selected, and then click Apply/Save to save your change.

3. On the left side of the gateway:

a. Activate the desired band by pressing 2.4 GHz or 5 GHz briefly on the rocker switch.

b. Activate WPS by pressing the desired band button and holding it down for 7 seconds.

4. Within 2 minutes, activate WPS on the 3rd party device to which you wish to connect. The device may have a

push button on its exterior that you can press, or a clickable button on a software interface. To learn how to use

the WPS feature on your client device, refer to its documentation.

Your device should now be connected to your gateway wirelessly using WPS. If you encounter problems with the WPS

setup such as connection failure, refer to your client device for further instructions.

Manual Method

Set up your gateway’s parameters first, then follow these steps.

1. In the left menu, click Wireless, the band that you want to configure, and then click Security.

2. Scroll down to the Manual Setup AP section.

3. If your gateway supports multiple wireless networks, select the SSID of the network you wish to configure. You

will need this ID for step 8.

4. Select the desired Network Authentication. Make sure that the host devices you intend to use support the

selected authentication type.

Altri manuali per SMART/RG SR516ac

Indice

Altri manuali ADTRAN Portale

ADTRAN

ADTRAN 324RG Manuale utente

ADTRAN

ADTRAN NetVanta 644 Manuale utente

ADTRAN

ADTRAN NetVanta 644 Manuale utente

ADTRAN

ADTRAN jobAid 424RG3 Manuale utente

ADTRAN

ADTRAN Total Access 908e Manuale

ADTRAN

ADTRAN SMART/RG SR501 Manuale utente

ADTRAN

ADTRAN NetVanta 1355 Manuale utente

ADTRAN

ADTRAN 4242908L1 Manuale utente

ADTRAN

ADTRAN 17600139F1 Manuale utente

ADTRAN

ADTRAN NetVanta 6310 Manuale utente

ADTRAN

ADTRAN SDX810-RG Manuale utente

ADTRAN

ADTRAN BroadCloud Manuale utente

ADTRAN

ADTRAN NetVanta 1355 Manuale utente

ADTRAN

ADTRAN NETVANTA 640 Series Manuale utente

ADTRAN

ADTRAN jobAid+ Total Access 324 Manuale utente

ADTRAN

ADTRAN 7310-8 Manuale utente

ADTRAN

ADTRAN jobAid+ Total Access 311 Manuale utente

ADTRAN

ADTRAN NetVanta 6240 Series Manuale utente

ADTRAN

ADTRAN SR820ac Manuale utente

ADTRAN

ADTRAN Total Access 912 Manuale utente

ADTRAN

ADTRAN 8612 Manuale utente

ADTRAN

ADTRAN 825-v6 Manuale del proprietario

ADTRAN

ADTRAN 834-v6 Manuale utente

ADTRAN

ADTRAN 424RG ONT Manuale utente

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente