Advantech B+B SmartWorx PoE Giga-McBasic Manuale utente

PoE & PoE+ Giga-McBasic

USER MANUAL

PoE & PoE+ Giga-McBasic LFPT

Advantech B+B SmartWorx - Americas

707 Dayton Road

Ottawa, IL 61350 USA

Phone 1 (815) 433-5100

Fax 1 (815) 433-5105

Advantech B+B SmartWorx - Europe

Westlink Commercial Park

Oranmore, Co. Galway, Ireland

Phone +353 91-792444

Fax +353 91-792445

www.advantech-bb.com

support@advantech-bb.com

PoE & PoE+ Giga-McBasic LFPT

CONTENTS

Introduction - PoE Giga-McBasic LFPT...................................................... 4

About PoE Giga-McBasic LFPT..................................................................................... 4

Installation.....................................................................................................................5

DIP Switch Configuration.............................................................................................. 5

PoE Reset DSW.............................................................................................................5

LFPT DIP Switches ........................................................................................................ 6

LED Operation.............................................................................................................. 6

Troubleshooting ............................................................................................................8

RJ-45 Pinouts ................................................................................................................ 8

Specifications ................................................................................................................ 9

Introduction – PoE+ Giga-McBasic LFPT ................................................... 9

About PoE+ Giga-McBasic LFPT.................................................................................10

Installation...................................................................................................................11

DIP Switch Configuration............................................................................................12

PoE Reset DSW...........................................................................................................12

LFPT DIP Switches ...................................................................................................... 12

LED Operation........................................................................................................... 13

Troubleshooting ..........................................................................................................15

RJ-45 Pinouts .............................................................................................................. 15

Specifications .............................................................................................................. 16

B+B SmartWorx Technical Support.......................................................... 17

Statements, Precautions, Guidelines, Regulatory..................................... 18

FCC Radio Frequency Interference Statement....................................................... 18

PoE Precautions (Inside Building Installation Only) .................................................... 18

Electrostatic Discharge (ESD) Precautions ..................................................................19

Fiber Optic Cleaning Guidelines.........................................................................19

Regulatory, Standards, Compliances .......................................................................... 20

PoE & PoE+ Giga-McBasic LFPT

INTRODUCTION - POE GIGA-MCBASIC LFPT

ABOUT POE GIGA-MCBASIC LFPT

NOTE:

Unless otherwise noted in this manual, any reference

applicable for both the 1x9 and SFP version

of the PoE Giga-McBasic LFPT.

The PoE Giga-McBasic is a solution for private network applications that

require Power-over-Ethernet (PoE) (IEEE802.3af) for installations inside

buildings where PoE is required to power an Ethernet device. The standalone

unit offers a model with one SFP or fixed fiber transceiver, 1x9, uplink for the

network connection, one PSE 10/100/1000Base-T copper port that provides

PoE and one 10/100/ 1000Mbps copper port, to connect a non-PoE unit to the

same fiber uplink. As a fiber-fed demarcation unit, it provides both power and

data to a remote device over a standard CAT5 copper line, eliminating the need

for a power connection to the remote device. The PoE Giga-McBasic LFPT

provides up to 15.4 Watts on one copper port and is powered by an internal

power supply, supporting 100-240 VAC. ( For more robust power requirements

on both copper ports, refer to the information about PoE+ Giga-McBasic LFPT.)

The SFP uplink can support fiber or copper SFPs. The fiber SFP, available in

SC or LC connectors, supports 100FDX or 1000FDX; a copper SFP supports

the SGMII interface (10/100/1000Mbps). The SFP, with or without DDMI, is

available for purchase from B+B SmartWorx. The SFP must be MSA-

compliant.

Copper ports auto-negotiate to the connected device’s speed and duplex mode:

10 Mbps, 100 Mbps or 1000 Mbps, and HDX or FDX (including Flow Control).

The PoE+ Giga-McBasic LFPT supports jumbo frames up to 10240.

NOTE: Some options require items that are sold separately, available from B+B SmartWorx.

PoE & PoE+ Giga-McBasic LFPT

INSTALLATION

PoE Giga-McBasic LFPT installs virtually anywhere: standalone, table-top

device, with rackmount ears, or using a wallmount bracket. The rackmount ears

and wallmount bracket are optional accessories available from B+B SmartWorx.

Several models of the PoE Giga-McBasic LFPT support single-strand fiber for operation.

Since single-strand fiber products

use

optics that transmit and receive on two different

wavelengths,

sin

-strand fiber products must be deployed in pairs. The two connected

products must also have

the

same speed and distance

DIP SWITCH CONFIGURATION

DIP

Switch

Name

Description

Default

Setting

DIP

Switch

PoE

Reset

ON forces Port 2, PSE/PoE, to OFF

LOS of fiber

input.

OFF

LFPT Port

ON enables LFPT for Port

and the

Port.

OFF

LFPT Port

ON enables LFPT for Port

and the

Port.

OFF

Factory

Set

Do not

change.

OFF

Factory

Set

Do not

change.

OFF

Factory

Set

Do not

change.

OFF

Factory

Set

Do not

change.

OFF

Factory

Set

Do not

change.

OFF

POE RESET DSW

When set to ON, it will force the PSE output power on the copper port OFF

when the LINK state is lost on the SFP line (copper or fiber SFP). By default,

the DSW is set to OFF.

PoE & PoE+ Giga-McBasic LFPT

LFPT DIP SWITCHES

The DIP Switches for LFPT allows a LOS fault to be passed through the unit.

When enabled, if link is lost on the FX port, the transmit on the TX port is

disabled. If link is lost on a TX port, the transmit on the FX Port is disabled.

NOTE:

With the fault switches

–

PoE Reset, LFPT Port 1 and LFPT Port 2, only one fault condition

recognized at

time. The first

fault

condition

in charge. So,

TX Port 1 has no link and then the FX Port loss

link, the loss of TX Port

link causes the FX Port

disable

transmit.

LED OPERATION

The PoE Giga-McBasic LFPT includes LEDs for three ports, as shown below:

PoE Giga-McBasic LFPT SFP

SFP LED Functions

FLT

Glows red when

fault has been detected on the

unit.

LNK

Glows green with

valid

link.

1000

Mbps

Glows green when SFP

running at

1000Mbps.

PWR

Glows green when unit

is powered.

RJ-45 LED Functions

LNK/ACT (TX1, TX2)

Glows green with

valid

link.

Blinks green when activity

is detected.

PSE

(TX2)

Glows green when port is supplying PoE

power.

Blinks green during fault conditions:

Hz flashes to indicate an overload or

short;

Hz flashes to indicate out-of-range voltage or

over-temperature.

Off

the port

not supplying

power.

FDX

(TX1)

Glows amber when port

running full-

duplex.

PoE & PoE+ Giga-McBasic LFPT

PoE Giga-McBasic LFPT 1x9

1x9 LED Functions

FLT

Glows red when

fault has been detected on the

unit.

LNK

Glows green with

valid

link.

1000

Mbps

Glows green when

running at

1000Mbps.

PWR

Glows green when unit

is powered.

RJ-45 LED Functions

LNK/ACT (TX1, TX2)

Glows green with

valid

link.

Blinks green when activity

is detected.

PSE

(TX2)

Glows green when port

supplying PoE

power.

Blinks green during fault conditions:

Hz flashes to indicate an

overload or short;

Hz flashes to indicate out-of-range voltage or

over-

temperature.

Off

the port

not supplying

power.

FDX

(TX1)

Glows amber when port

running full

duplex.

NOTE:

The fixed twisted-pair port labeled PSE is the only port capable of providing

PoE.

PoE & PoE+ Giga-McBasic LFPT

TROUBLESHOOTING

•PWR LED glows green when the unit is powered. If this LED is not lit,

contact B+B SmartWorx Technical

Support.

•Blinks green during fault conditions: 1 Hz flashes to indicate an overload or

short; 4 Hz flashes to indicate out-of-range voltage or over-temperature. The

PSE LED should maintain solid green, to indicate consistent power. Check

the PD device and its requirements.

RJ-45 PINOUTS

The following table lists the pin configuration for the RJ-48 connector.

Pin#

Signal Name

1000M

Signal Direction

10/100M

PoE & PoE+

(ALT-B)

TXD1+

Out*

TXD1-

Out*

RXD2+

In*

D3+

D3-

RXD2-

In*

D4+

-V

D4-

-V

PoE & PoE+ Giga-McBasic LFPT

SPECIFICATIONS

Ethernet Connections

•10/100/1000 BaseT

•Auto Negotiation

•Auto Cross

•Flow Control

•10240 MTU

•Full Line-Rate Forwarding

Input Specifications

100 to 240 ±10% VAC Input, 50/60 Hz, 0.5A to 0.2A

Operating Temperature

0 to +50 °C (+32 to +122 °F)

Storage Temperature

-40 to +85 °C (-40 to +185 °F)

Humidity

5 to 95% (non-condensing); 0 to 10000 ft. altitude

Dimensions

3.71H x 12.09W x 18.59D cm (1.46H x 4.76W x 7.32D in)

Power Characteristics

Consumes < 10 Watts (heating) plus PSE power

IEEE802.3af Power to Field <15.5 Watts

Standards Compliance

•IEEE 802.3af Power-over-Ethernet

•IEEE 802.3 Ethernet Standards

•IEEE 802.3u Auto Giga-McBasic LFPT

PoE & PoE+ Giga-McBasic LFPT

ABOUT POE+ GIGA-MCBASIC LFPT

NOTE:

Unless otherwise noted in this manual, any reference

applicable for both the 1x9

and SFP version of the PoE+ Giga-McBasic LFPT.

PoE+ Giga-McBasic LFPT is a solution for private network applications that

require Power-over-Ethernet (PoE) (IEEE802.3af) for locations inside buildings

where PoE is required to power an Ethernet device. The standalone unit offers

a model with one SFP or fixed fiber transceiver, 1x9, uplink for the network

connection, two PSE 10/100/1000Base-T copper ports that provide PoE to

connect a non-PoE unit to the same fiber uplink. As a fiber-fed demarcation

unit, it provides both power and data to a remote device over a standard CAT5

copper line, eliminating theneed for a power connection to the remote device.

The PoE+ Giga-McBasic LFPT provides up to 25.5 Watts per copper port and

is powered by an internal power supply, supporting 100-240 VAC.

The SFP uplink can support fiber or copper SFPs. The fiber SFP, available in

SC or LC connectors, supports 100FDX or 1000FDX; a copper SFP supports

the SGMII interface (10/100/1000Mbps). The SFP, with or without DDMI, is

available for purchase from B+B SmartWorx. The SFP must be MSA-

compliant.

The copper ports auto negotiate to the connected device’s speed and duplex

mode: 10 Mbps, 100 Mbps or 1000 Mbps, and HDX or FDX (including Flow

Control). The PoE+ Giga-McBasic supports jumbo frames up to 10240.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Advantech Convertitore multimediale

Advantech

Advantech B+B SmartWorx 485OI9TB Manuale utente

Advantech

Advantech EKI-2741FI Manuale utente

Advantech

Advantech B+B SmartWorx BB-485USBTB-2W-A Manuale utente

Advantech

Advantech B+B SmartWorx Giga-MiniMc 856-10730-TX Manuale utente

Advantech

Advantech B+B SmartWorx 232USB9M Manuale utente

Advantech

Advantech ADAM-4562 Manuale utente

Advantech

Advantech BB-USO9ML2-A Manuale utente

Advantech

Advantech ADAM-4561 Manuale utente

Advantech

Advantech IMC-574I-SFP Manuale utente

Advantech

Advantech BB-485LDRC9 Manuale utente

Advantech

Advantech BB-SCP211-DFTB3 Manuale utente

Advantech

Advantech PCI-1784U Manuale utente

Advantech

Advantech PCIE-1182 Manuale di installazione e funzionamento

Advantech

Advantech BB-422PP9TB Manuale utente

Advantech

Advantech ADAM-6541 Manuale utente

Advantech

Advantech B+B SmartWorx 485DRCI-PH Manuale utente

Advantech

Advantech PCIE-1884 Manuale utente

Advantech

Advantech BB-USOPTL4DR-2 Manuale utente

Advantech

Advantech VEGA-2002 Manuale utente

Advantech

Advantech B+B SMARTWORX 485LDRC9 Manuale utente

Advantech

Advantech BB-USOPTL4 Manuale utente

Advantech

Advantech EKI-2741SX Manuale utente

Advantech

Advantech EKI-2741F Manuale utente

Advantech

Advantech VEGA-2001 Manuale di istruzioni

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente