Ag-Tester HT101S Manuale utente

HT101S Reference Manual

OVERVIEW

The HT101S from Ag-Tester is our handheld designed to interface with

various sensors found on agricultural machinery and be a complete system

diagnostic tool.

The types of sensors that can be interfaced with include:

Liquid Flow Sensors, Pressure Sensors, Motion Sensors, Shaft Speed

Sensors, Position Sensors and others.

The top section of the HT101S is the meter. The user can make

measurements including Volts, Frequency and Resistance,

The lower part of the HT101S is the diagnostic and sensor simulator center.

When used with the “In-Line” Tester TEE Harness the HT101S will monitor the Voltages supplied to the sensor, from the

display, and additionally allow the signals generated by the sensor to be checked for presence and accuracy. When

dialed to Digital or Analog Simulate, the HT101S sends simulated signals to the display allowing all the connecting cables

to be checked while verifying the Controlling Display correctly reads the signals being sent.

When used with the “Stand-Alone” Tester TEE Harness any sensor can be fully tested on the bench.

The back panel provides connections for inputs and charging along with the magnetic RAM Mount.

RAM MOUNT/ MAGNET

INPUT CONNECTOR CHARGER INPUT

Connect the Tester TEE

Harness Here

METER FUNCTIONS

The “Meter Function” switch selects the type of

measurement being made. Select from the following:

VOLTS 0 to 50 Volts DC with automatic polarity sensing

FREQ Frequency 0 to 1000 HZ

CONT “Continuity” or “Ohms” 0 to 2000

The “Connected Point” switch selects the testing method.

There are 4 options. TEST, PATCH, COAX, or BATT CHECK

When dialed to TEST the

standard meter test leads are installed in

the RED outlined lead jacks. The meter can

then be used as you would a standard test

meter.

Dial to PATCH to use the Patch Cables

connecting at the Green outlined lead

jacks. This allows an easy connection to

the wires connecting the Display console

to the sensors.

Setting the CONNECTED POINT to COAX allows for an

easy connection to a TNC type coax connector. Most GPS

receivers send 5 volts to the antenna to operate an

internal amplifier. Disconnect the cable from the gps

antenna and re-install at COAX on the HT101S. When

VOLTS is selected you should see 5 to 12 volts on the

meter indicating a good connection from the antenna

connection to the gps receiver.

When dialed to BATT CHECK and VOLTS the meter indicates the

current internal battery voltage. Fully charged it may read as high as

13.5 VDC. The tester will function properly until below 12 volts. No

wire connection is required. Battery can be checked while

performing other tests.

The “Pulse Catcher” LEDs blink when pulses are present on the wire

being tested. This function is active when “Frequency” is selected.

DIAGNOSTIC FUNCTIONALITY and SENSOR TESTING FUNCTIONS

The HT101S Function Switch is located in the lower, center position of

the Tester. When dialed to any position except “OFF” the meter

functions are all available.

Set to MONITOR to use the Tester as a standard meter or to make tests

of the complete connection of the Display to the Sensor being tested.

When connected using the “In-Line” Tester TEE Harness, there are 3

possible connections made available for tests. A 3 wire sensor will have

a ground, a positive supply voltage and a signal line. The HT101S makes

these connections available for testing with Test Jacks and any voltages

present will be displayed by the associated LEDs.

Test Jacks and LEDs are colorized to indicate:

RED = Supply Voltage from Display

Yellow = Signal

Two wire sensors won’t have a wire for power. These might include magnetic sensors and switches.

When dialed to “DIGITAL SIMULATE” two test functions are made available depending on the type of connecting harness

being used.

When using the In-Line harness, DIGITAL SIMULATE allows the HT101S to send a continual Test Signal back to the

Display. These are digital pulses where the frequency of the generated test signal is controlled by the “SET DIGITAL”

control. When fully counterclockwise the signal is at about 30 Hz or 30 pulses per second. Turning the control clockwise

will increase the frequency to 350 Hz or so. This is a sure way to locate cable trouble from the sensor to the display while

at the same time verifying the display is programmed to receive these digital signals.

When the Stand-Alone harness is used, DIGITAL SIMULATE is used to check the sensor, independent from the display.

The HT101S provides the Supply Voltage and the Signal Generated is available for tests at the YELLOW test jack. You’ll

see the Yellow LED blink as the pulses are generated and the Frequency can

be read by connecting the Meter to the Yellow and Black test jacks.

SET ANALOG allows the same type of tests to be performed but are used

with Analog Sensors.

When the In-Line harness is connected you can monitor the Supply Voltage

and the Generated Signal from the display to the sensor.

The Stand-Alone Harness allows for testing of the sensor independent from

the Display. The HT101S provides the Supply Voltage and Ground and the

generated signal is made available for test at the YELLOW test jack.

TYPES OF SENSORS TO BE TESTED

The HT101S is designed to be compatible with any sensor on any machine. In some cases special cabling is needed.

These sensors require in some cases, very specific operating voltages. Sensors generally fall into two groups; DIGITAL

and ANALOG.

DIGITAL sensors generate PULSES which vary in FREQUENCY as changes occur.

Shaft Speed sensors are used in many applications from Dry Product Applicators

to Planters. They will generate a certain number of “pulses per revolution”. The

RAVEN sensor to the right generated 180 pulses per revolution. Others might

generate 60 or 360 pulses in a single revolution. This is the reference point for

the display. Cutting the pulses in half tells the console the shaft is running at half

speed. Doubling the pulses indicates double the speed. “Pulses per revolution” is

the calibration reference the display requires.

Flow Meters generate pulses reflecting the amount

of flow currently running through the meter. A

calibration Tag is generally attached and indicates

the “Pulses Per Gallon” generated by the sensor. This RAVEN Flowmeter has a

tag showing 730 which in the case of RAVEN indicate 73 pulses generated per gallon of liquid flow. The generated pulses

are linear in their output meaning, doubling the pulses means double the gallons.

ANALOG sensors have signals that vary in VOLTAGE as changes occur.

The graph to the left shows how a 100 pound pressure

sensor varies in voltage generated as the pressure

changes. Zero pounds of pressure is indicated with a

voltage generated of zero. At 100 pounds of pressure the

signal voltage is at 100. The sensor responds in a linear

fashion. 50 pounds is then indicated by a 2.5 volt signal.

A zero to 3000 pound pressure found in hydraulic systems

will also respond in a linear way with zero volts indicating zero pressure and a 5 volt

signal is generated at 3000 pounds.

Another analog sensor might be a POSITION SENSOR used to indicate the steering position on a GPS Auto-Steer System.

Hitch position sensors are also this type. Movement is indicated by a linear change in voltage.

Using the HT101S Stand-Alone Testing

Stand-Alone testing is used as a method of testing and evaluating or “bench testing” a sensor, independent of the

display.

Use the Tester TEE Harness and adapters if required to match the sensor being tested. Sensors are very sensitive to

correct voltages being applied. Some are 12 volt supply where others are specific at 8 volts or 5 volts. There are sensors

that work with a great variety of supplied voltages.

We’re using the Tester Tee Cable, TT- AE27993 Stand Alone in the following tests.

Shaft Speed Sensors

Set the Function Switch to “Digital

Simulate. Set the Meter Function to

“FREQ”, Frequency. Set the Connected

Point to “Patch “ and install the Patch

Cables from the Meter to the Yellow

and Black Test Jacks. As you slowly turn

the shaft of the sensor you’ll see the Yellow LED Blink as the pulses are

generated. The faster you spin the shaft, the faster the light blinks. You

can read the Frequency of the generated pulses on the meter.

These are best tested using a variable speed drill. Holding the speed constant should provide a steady frequency output.

These sensors may become unstable in frequency with the shaft speed constant. If the sensor is on a machine, just

watch for a steady frequency indication with a constant shaft speed.

Flow Sensors

Flow Meters can be bench using the HT101S set up as done for the Shaft Speed Sensors.

Set the Function Switch to Digital Simulate. Set the Meter Function to

Frequency and the Connected Point to Patch. Install the Patch Cables from the

meter to the Yellow and Black Test Jacks.

Blow through the flowmeter and the turbine will

spin. As the turbine spins pulses are generated.

You’ll see the Yellow LED Blink and the Frequency

can be read on the meter. The Pulse Catcher will

blink indicating pulses are present.

Pressure Sensors

When testing Pressure Sensors set the

Function Switch to Analog Simulate. Set

the Meter Function to Volts and the

Connected Point to Patch. Install the test

leads from the meter to the Yellow and

Black test jacks.

Typically ZERO Pressure will result in a

signal voltage of 0.5 Volts As the pressure

increases the voltage increase smoothly until maximum pressure indicated by a signal of

5.0 volts. 1/2 Pressure will generate 2.5 volts of signal. You can easily test these sensors

while installed on a machine. Zero to 100 pound sensors can be tested on the bench using

air pressure regulated to provide the test pressures. Hydraulic pressure sensors need

typically 3,000 pounds of pressure which can be a challenge providing on the bench.

Using the HT101S In-Line Testing

Use Tester TEE In-Line Harness TT-AE27994

To Tester

To Sensors To Display

Install the harness between the sensor and the display. The Red and Yellow LEDs indicate

voltages coming from the display and sensor. When installed the RED power LED will light. If

not either the cable is bad going back to the display or the display is not turned on. The

Yellow LED may be lit or not depending on the status of the sensor. The signals from digital

sensors like Flow Meter and Shaft Sensors vary from Zero to 5 volts generally. The light will blink indicating pulses.

Use the Patch Cables checking the Display Power at the RED and BLACK Test Leads. Check the signal Voltage and

Frequency using the Black and Yellow Test Jacks.

Battery Care- HT101V and HT101S Testers

These testers are equipped with a high power, 12 volt 1000 MAH Nickel- Cadmium “NI-

Cad” battery. The testers will run about 10 hours constant without a re-charge. Re-

Charge takes about 4 hours.

The battery level can easily be checked using the voltmeter built into the tester.

Turn the tester ON, set to VOLTS, and Connected Point

to BATT CHECK. The current voltage will be

displayed.

After a full charge, it may read in excess is 13 volts, then will stabilize at about 12.2 to

12.8 volts.

Ni-CAD batteries develop a memory over time. If they are recharged after each short

usage, they will develop that memory and at some point only deliver that capacity. MAXIMUM battery life with the

strongest usage cycle is achieved by charging the battery when the voltage drops below 12.0 volts. Check the voltage as

your putting away the tester. If the voltage is 12.0 volts or less, recharge.

Use only the SMART CHARGER that came with the tester. The charger will turn

itself off when the battery is charged so there is no chance of

overcharging.

The charge indicator light turns RED when charging and when fully charged the

light turns green.

Batteries are replaced at Ag-Tester. Go to agtester.com for details.

Tester- Tee Harnessing

To understand the flow of circuits and over-all Ag-Tester product design, one needs to start with an understanding of

the interface harnessing, “Tester-Tee Harnesses”. Two harnesses are used for full Tester functionality.

TT- AE27994 In-Line Harness TT- AE27993 Stand-Alone Harness

1- In-Line Harnessing. This is used for full system diagnostic operations where the full connection from the

display to the sensor or valve is intact. Here, the system is left intact with the Ag-Tester Tool inserted in the line

feeding the Valve or Sensor in question from the balance of the system.

a. When in the “monitor mode” “Tip Jacks” are available representing each possible connection between

the component and the rest of the system. This provides a connection point for either, the Ag-Tester

Tool or another meter, oscilloscope or some other tool so tests can be performed to determine the

cause of the problem.

b. When in the other provided “modes of operation” the circuit control lines are disconnected between

the component and system balance to allow for diagnostic functions to be performed.

i. The “HT101S” allow the sensor to be independently tested while at the same time sending

feedback to the system balance to allow for diagnostics.

2- Stand-Alone Harnessing. Stand-alone harnessing allows for components to be “bench tested”. Using the

stand-alone harness allows that the Ag-Tester Tool provides the operational power and signals to the devise

being tested to fully test the component.

a. Monitor mode is not used unless using the Tester as a “multi-meter” for basic tests.

b. When in other modes of operation, the type of test being performed is selected. The Tip Jacks do not

represent the “Power Supplied” “Red LED” using this function.

i. The HT101S allows for either digital or analog sensors to be tested with the HT101S providing

operational power and signal paths for analysis. The test jacks and Led indicators are available

for tests on signal lines.

Sensor

Display

To Sensor

To Display

In-Line Harness for Sensors-HT101S

Ag-Tester Tool- HT101S

Tip Jacks and LEDs

Power

from

Display

Power

from

Display

Signal

Display

Signal

from

Sensor

Ground

from

Tester

Volts

from

Tester

+12

Volts

from

Tester

Ground (-)

Signal

Power (+)

Ground (-)

Signal

Power (+)

Digital

and

Analog

Simulator

To Tester- 7 Pin AMP

Indice

Altri manuali Ag-Tester Apparecchiature di prova

Ag-Tester

Ag-Tester CT1000 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente