Agilent Technologies CrossLab CS Manuale utente
Agilent CrossLab CS
Electronic Leak Detector
Operation Manual
Notices
© Agilent Technologies, Inc. 2021
No part of this manual may be reproduced
in any form or by any means (including
electronic storage and retrieval or
translation into a foreign language) without
prior agreement and written consent from
Agilent Technologies, Inc. as governed by
United States and international
copyright laws.
Manual Part Number
G6693-90000
Edition
First edition, November 2021
Printed in USA
Agilent Technologies, Inc.
412 Ying Lun Road
Waigoaqiao Freed Trade Zone
Shanghai 200131 P.R.China
Warranty
The material contained in this document is
provided “as is,” and is subject to being
changed, without notice, in future editions.
Further, to the maximum extent permitted
by applicable law, Agilent disclaims all
warranties, either express or implied, with
regard to this manual and any information
contained herein, including but not limited to
the implied warranties of merchantability
and fitness for a particular purpose. Agilent
shall not be liable for errors or for incidental
or consequential damages in connection
with the furnishing, use, or performance of
this document or of any information
contained herein. Should Agilent and the
user have a separate written agreement
with warranty terms covering the material in
this document that conflict with these
terms, the warranty terms in the separate
agreement shall control.
Safety Notices
CAUTION
A CAUTION notice denotes a
hazard. It calls attention to an
operating procedure, practice, or the
like that, if not correctly performed or
adhered to, could result in damage to
the product or loss of important
data. Do not proceed beyond a
CAUTION notice until the indicated
conditions are fully understood
and met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or the
like that, if not correctly performed or
adhered to, could result in personal
injury or death. Do not proceed
beyond a WARNING notice until the
indicated conditions are fully
understood and met.
Agilent CrossLab CS Electronic Leak Detector Operation Manual 3
Leak Detector
Introduction 5
Power/Mode button 5
Enter/Clear/Toggle button 6
Switching the leak detector On and Off 7
Notes, Cautions, and Warnings 8
Product Specifications 11
Detection Sensitivity to Gases 12
Operating Modes 13
Warm Up mode 13
Detection mode 14
Info mode 16
Detecting Leaks 24
Replacing and Servicing the Probe Filter 25
USB interface 26
Warning and Error Indications 28
Warning indication 28
Error indication 28
Low battery indication 29
Power Indications 30
Installing and Replacing the Cartridge 31
Installing the cartridge 31
Swapping or replacing the cartridge with ADM
Flow Meter cartridge 32
Replacing the Batteries 34
Upgrading the Firmware 36
Using the Leak Detector Stand 36
Leak Detector
Introduction
Agilent CrossLab CS Electronic Leak Detector Operation Manual 5
Introduction
The Agilent leak detector is controlled with two buttons on the
front of the instrument directly below the screen, as shown in
Figure 1. The functions of these buttons are described in
this section.
Power/Mode button
The Power/Mode button is used to switch the leak detector on
and off, as well as to scroll through and select different
operational modes.
•To turn on the instrument, briefly press and release the
Power/Mode button.
•To turn off the instrument, press and hold the Power/Mode
button for three seconds.
•To scroll through the available modes, when the
instrument is on, briefly press and release the
Power/Mode button.
Figure 1. The Agilent CrossLab CS leak detector front screen buttons.
Leak Detector
Enter/Clear/Toggle button
6 Agilent CrossLab CS Electronic Leak Detector Operation Manual
Enter/Clear/Toggle button
The Enter/Clear/Toggle button is used to access additional
functionality within the operating modes.
•To reset the baseline of detection in Detection mode,
briefly press and release Enter/Clear/Toggle button.
•To change the settings in Info mode, press and hold the
Enter/Clear/Toggle button for two seconds.
Leak Detector
Switching the leak detector On and Off
Agilent CrossLab CS Electronic Leak Detector Operation Manual 7
Switching the leak detector On
and Off
With the Leak Detector powered off, briefly press and release
Power/Mode button to turn the unit on. The screen will flash the
words Leak Detector for approximately three seconds, then
begin operating.
With the unit powered on, press and hold the Power/Mode
button for three seconds to power down the unit.
Figure 2. The initial screen display for the Agilent leak detector.
Figure 3. The shutdown screen for the Agilent leak detector.
Leak Detector
Notes, Cautions, and Warnings
8 Agilent CrossLab CS Electronic Leak Detector Operation Manual
Notes, Cautions, and Warnings
NOTE
•The tubing is not replaceable. Do not attempt to remove
the tubing.
•The filter is the only serviceable part in the leak
detector cartridge.
•Annual calibration for the leak detector cartridge is
not necessary.
•Update to the latest firmware if the leak detector cartridge
is being used with ADM Flow Meter mainframe with
firmware version 1.2.1911.1501 and below.
CAUTION
• Do not use the leak detector to detect corrosive gases.
• Do not expose the probe tip to extreme sources of heat.
• Do not use the leak detector to probe in areas where
there are solvents or liquids (such as snoop).
• Do not use the leak detector in temperatures outside of
its specified operating range.
• Do not use the leak detector in high humidity
environments outside of its specified humidity range.
• The probe should not be misused for other purposes
except to conduct sniffing in suspected leak areas.
WARNING
• Use only a 5 V DC, 0.5 A USB power source and the
supplied USB cable to run this device.
• Do not use the leak detector in hazardous environments
where there are large leaks of flammable gases.
• Do not use the leak detector as safety equipment.
Leak Detector
Notes, Cautions, and Warnings
Agilent CrossLab CS Electronic Leak Detector Operation Manual 9
WARNUNGWARNUNG
• Verwenden Sie zum Aufladen dieses Geräts
ausschließlich eine 5v DC, 0,5A USB-Stromquelle und das
mitgelieferte USB-Kabel.
• Verwenden Sie den Lecksucher nicht in gefährlichen
Umgebungen, in denen große Mengen an brennbaren
Gasen austreten.
• Verwenden Sie den Lecksucher nicht als
Sicherheitsausrüstung.
ATTENTION
• Utilisez uniquement une source d'alimentation USB 5 V
CC, 0,5 A et le câble USB fourni pour charger cet appareil.
• N'utilisez pas le détecteur de fuites dans des
environnements dangereux où de grandes fuites de gaz
inflammables existent.
• N’utilisez-pas le détecteur de fuites comme équipement
de sécurité.
ATTENZIONE
• Per caricare questo dispositivo, utilizzare solo una fonte
di alimentazione USB da 5 V CC, 0,5 A e il cavo USB in
dotazione.
• Non utilizzare il rilevatore di fughe in ambienti pericolosi
in cui vi siano importanti fughe di gas infiammabili.
• Non utilizzare il rilevatore di fughe come apparecchiatura
di sicurezza.
ADVERTENCIA
• Para cargar este dispositivo, use solamente una fuente
de alimentación USB de 0,5A, DC 5V y el cable de
alimentación suministrado.
• No utilice el detector de fugas en entornos peligrosos en
los que existen grandes fugas de gases inflamables.
• No use el detector de fugas como equipo de seguridad.
Leak Detector
Notes, Cautions, and Warnings
10 Agilent CrossLab CS Electronic Leak Detector Operation Manual
警告
•仅使用 5v DC、0.5A USB 电源和随附的 USB 电缆为本设
备充电。
•请勿在有⼤量易燃⽓体泄漏的危险环境中使用检漏仪。
•请勿将检漏仪用作安全设备。
Altri manuali per CrossLab CS
2
Indice
Altri manuali Agilent Technologies Sensore di sicurezza
Agilent Technologies
Agilent Technologies 1100 Series Manuale utente
Agilent Technologies
Agilent Technologies 7250 Manuale utente
Agilent Technologies
Agilent Technologies G3437A Manuale utente
Agilent Technologies
Agilent Technologies Helium Manuale utente
Agilent Technologies
Agilent Technologies VS Series Manuale utente
Agilent Technologies
Agilent Technologies 5973N Manuale
Agilent Technologies
Agilent Technologies 5975 Series Manuale
Agilent Technologies
Agilent Technologies InfinityLab 1290 Infinity II Manuale utente
Agilent Technologies
Agilent Technologies 1100 Series Manuale utente
Agilent Technologies
Agilent Technologies 355 SCD Manuale utente
Agilent Technologies
Agilent Technologies 1260 Infinity Manuale utente
Agilent Technologies
Agilent Technologies VS C15 Series Guida
Agilent Technologies
Agilent Technologies 1200 series Manuale utente
Agilent Technologies
Agilent Technologies 8480 Series Manuale di servizio
Agilent Technologies
Agilent Technologies 5973N Istruzioni operative
Agilent Technologies
Agilent Technologies 1260 Infinity Manuale utente
Agilent Technologies
Agilent Technologies 1260 Infinity Manuale utente
Agilent Technologies
Agilent Technologies NPD Manuale utente
Agilent Technologies
Agilent Technologies PHD-4 Manuale utente
Agilent Technologies
Agilent Technologies G3388B Manuale di installazione
