Agilent Technologies E5091A Manuale utente
Caution
Do not exceed the operating input power, voltage, and current
level and signal type appropriate for the instrument being used, refer to
your instrument's Function Reference.
Electrostatic discharge(ESD) can damage the highly sensitive
microcircuits in your instrument. ESD damage is most likely to occur as
the test fixtures are being connected or disconnected. Protect them from
ESD damage by wearing a grounding strap that provides a high
resistance path to ground. Alternatively, ground yourself to discharge any
static charge built-up by touching the outer shell of any grounded
instrument chassis before touching the test port connectors.
Safety Summary
When you notice any of the unusual conditions listed below, immediately
terminate operation and disconnect the power cable.
Contact your local Agilent Technologies sales representative or
authorized service company for repair of the instrument. If you continue
to operate without repairing the instrument, there is a potential fire or
shock hazard for the operator.
- Instrument operates abnormally.
- Instrument emits abnormal noise, smell, smoke or a spark-like
light during operation.
- Instrument generates high temperature or electrical shock
during operation.
- Power cable, plug, or receptacle on instrument is damaged.
- Foreign substance or liquid has fallen into the instrument.
Herstellerbescheinigung
GER
AUSCHEMISSION
LpA
<
70 dB
am Arbeitsplatz
normaler Betrieb
nach DIN 45635 T.19
Manufacturer's Declaration
ACOUSTIC NOISE EMISSION
LpA
<
70 dB
operator position
normal operation
per ISO 7779
Regulatory compliance information
This product complies with the essential requirements of the following applicable European Directives, and
carries the CE marking accordingly:
The Low Voltage Directive 73/23/EEC, amended by 93/68/EEC
The EMC Directive 89/336/EEC, amended by 93/68/EEC
To obtain Declaration of Conformity, please contact your local Agilent Technologies sales office, agent or
distributor.
Safety notice supplement
・This equipment complies with EN/IEC61010-1:2001.
・This equipment is MEASUREMENT CATEGORY I (CAT I). Do not use for CAT II, III, or IV.
・Do not connect the measuring terminals to mains.
・This equipment is POLLUTION DEGREE 2, INDOOR USE product.
・This equipment is tested with stand-alone condition or with the combination with the accessories supplied
by Agilent Technologies against the requirement of the standards described in the Declaration of
Conformity. If it is used as a system component, compliance of related regulations and safety requirements
are to be confirmed by the builder of the system.
Agilent E5091A Multiport Test Set
User’s Guide
Third Edition
Agilent Part No. E5091-90020
November 2005
2
Notices
The information contained in this document is subject to change without notice.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be photocopied, reproduced, or translated to
another language without the prior written consent of Agilent Technologies.
Microsoft®,MS-DOS®,Windows®,Visual C++®,Visual Basic®,VBA®and Excel®are
registered
UNIX is a registered trademark in U.S. and other countries, licensed
exclusively through X/Open Company Limited.
Portions ©Copyright 1996, Microsoft Corporation. All rights reserved.
© Copyright 2002, 2005 Agilent Technologies
Manual Printing History
The manual’s printing date and part number indicate its current edition. The printing date
changes when a new edition is printed (minor corrections and updates that are incorporated
at reprint do not cause the date to change). The manual part number changes when
extensive technical changes are incorporated.
April 2002 First Edition (part number: E5091-90000)
October 2002 Second Edition (part number: E5091-90010)
November 2005 Third Edition (part number: E5091-90020)
3
Safety Summary
The following general safety precautions must be observed during all phases of operation,
service, and repair of this instrument. Failure to comply with these precautions or with
specific WARNINGS elsewhere in this manual may impair the protection provided by the
equipment. Such noncompliance would also violate safety standards of design,
manufacture, and intended use of the instrument. Agilent Technologies assumes no liability
for the customer’s failure to comply with these precautions.
NOTE The E5091A complies with INSTALLATION CATEGORY II as well as POLLUTION
DEGREE 2 in IEC61010-1. The E5091A is an INDOOR USE product.
NOTE The LEDs in the E5091A are Class 1 in accordance with IEC60825-1,
CLASS 1 LED PRODUCT
NOTE This equipment is MEASUREMENT CATEGORY I (CAT I). Do not use for CAT II, III, or
IV.
NOTE This equipment is tested with stand-alone condition or with the combination with the
accessories supplied by Agilent Technologies against the requirement of the standards
described in the Declaration of Conformity. If it is used as a system component,
compliance of related regulations and safety requirements are to be confirmed by the
builder of the system.
• Ground the Instrument
To avoid electric shock, the instrument chassis and cabinet must be grounded with the
supplied power cable’s grounding prong.
• DO NOT Operate in an Explosive Atmosphere
Do not operate the instrument in the presence of inflammable gasses or fumes.
Operation of any electrical instrument in such an environment clearly constitutes a
safety hazard.
• Keep Away from Live Circuits
Operators must not remove instrument covers. Component replacement and internal
adjustments must be made by qualified maintenance personnel. Do not replace
components with the power cable connected. Under certain conditions, dangerous
voltage levels may remain even after the power cable has been disconnected. To avoid
injuries, always disconnect the power and discharge circuits before touching them.
• DO NOT Service or Adjust the Instrument Alone
Do not attempt internal service or adjustment unless another person, capable of
rendering first aid and resuscitation, is present.
• DO NOT Substitute Parts or Modify the Instrument
To avoid the danger of introducing additional hazards, do not install substitute parts or
perform unauthorized modifications to the instrument. Return the instrument to an
Agilent Technologies Sales and Service Office for service and repair to ensure that
4
safety features are maintained in operational condition.
• Dangerous Procedure Warnings
Warnings, such as the example below, precede potentially dangerous procedures
throughout this manual. Instructions contained in the warnings must be followed.
WARNING Dangerous voltage levels, capable of causing death, are present in this instrument.
Use extreme caution when handling, testing, and adjusting this instrument.
Safety Symbols
General definitions of safety symbols used on the instrument or in manuals are listed
below.
Instruction Manual symbol: the product is marked with this symbol when it is necessary for
the user to refer to the instrument manual.
Alternating current.
Direct current.
On (Supply).
Off (Supply).
In-position of push-button switch.
Out-position of push-button switch.
A chassis terminal; a connection to the instrument’s chassis, which includes all exposed
metal structure.
Stand-by.
WARNING This warning sign denotes a hazard. It calls attention to a procedure, practice, or
condition that, if not correctly performed or adhered to, could result in injury or
death to personnel.
CAUTION This Caution sign denotes a hazard. It calls attention to a procedure, practice, or condition
that, if not correctly performed or adhered to, could result in damage to or destruction of
part or all of the instrument.
NOTE This Note sign denotes important information. It calls attention to a procedure, practice, or
condition that is essential for the user to understand.
Indice
Altri manuali Agilent Technologies Apparecchiature di prova
Agilent Technologies
Agilent Technologies E5022B Manuale del proprietario
Agilent Technologies
Agilent Technologies InfiniiVision 5000 Series Manuale utente
Agilent Technologies
Agilent Technologies U1604A Manuale utente
Agilent Technologies
Agilent Technologies 1153A Guida alla risoluzione dei problemi
Agilent Technologies
Agilent Technologies 54522A Manuale utente
Agilent Technologies
Agilent Technologies Infiniium 90000 Q-Series Manuale utente
Agilent Technologies
Agilent Technologies 54621A Manuale utente
Agilent Technologies
Agilent Technologies 16043A Manuale operativo
Agilent Technologies
Agilent Technologies Infiniium 90000 Q-Series Manuale
Agilent Technologies
Agilent Technologies 85050B Manuale
Agilent Technologies
Agilent Technologies U1401A Manuale utente
Agilent Technologies
Agilent Technologies 16442A Manuale utente
Agilent Technologies
Agilent Technologies 85054D Manuale
Agilent Technologies
Agilent Technologies 16048G Manuale operativo
Agilent Technologies
Agilent Technologies 16197A Manuale operativo
Agilent Technologies
Agilent Technologies TS-5400 Manuale elenco delle parti
Agilent Technologies
Agilent Technologies U3025AE10 Manuale utente
Agilent Technologies
Agilent Technologies 8960 Manuale di installazione e funzionamento
Agilent Technologies
Agilent Technologies auroraSonata Manuale utente
Agilent Technologies
Agilent Technologies 8960 Manuale utente
Agilent Technologies
Agilent Technologies Infinium DCA 86100A Manuale utente
Agilent Technologies
Agilent Technologies DisplayPort Manuale di installazione e funzionamento
Agilent Technologies
Agilent Technologies 54620 Series Istruzioni operative e di sicurezza
Agilent Technologies
Agilent Technologies 280-DS Manuale utente
