Agilent Technologies TriScroll 800 Manuale utente

INSTALLATION AND

OPERATION MANUAL

Vacuum Products Division

DRAFT 10/9/14

TriScrollTM 800

Inverter Dry Scroll

Vacuum Pump

Manual No. 699904435

Revision B

October 2014

Agilent, Inc.

DRAFT 10/9/14

TriScroll™800 Inverter

Dry Scroll Vacuum Pump

TriScroll is a trademark of Agilent, Inc.

iii

TriScroll 800 Inverter Vacuum Pump

Table of Contents

Warranty ....................................................................vii

Warranty Replacement and Adjustment...............vii

Instructions for Use ..................................................... 1

General Information ................................................. 1

Storage ................................................................. 1

Unpacking and Inspection........................................ 1

Installation Requirements ......................................... 2

Safety ................................................................... 2

Mechanical Connections.......................................... 4

Pump Location ..................................................... 4

Vacuum Pump Isolation Valve.............................. 4

Pump Inlet............................................................ 4

Pump Exhaust....................................................... 4

Gas Ballast ........................................................... 4

Bearing Purge ....................................................... 4

Operation................................................................. 5

Startup Procedure ................................................. 5

Shutdown Procedure ............................................ 5

Maintenance ............................................................ 5

TriScroll 800 Inverter Pump Components View ........ 6

Technical Information ................................................. 7

Pump Electrical Controller........................................ 9

Technical Specifications ....................................... 9

Serial Interface Specification RS485 and RS232.. 10

Purge Kit ................................................................ 12

Exhaust Silencer Kit ................................................ 12

Vibration Isolation Kit............................................. 12

HEPA Inlet filter...................................................... 12

Troubleshooting ..................................................... 13

Maintenance .......................................................... 14

General Information ........................................... 14

Related TriScroll Manuals................................... 14

Maintenance and Tooling Kits ............................ 14

Factory Service Options...................................... 15

Accessories......................................................... 15

Contacting Agilent.............................................. 15

Request for Return Health and Safety Certification

TriScroll 800 Inverter Vacuum Pump

This page intentionally left blank.

TriScroll 800 Inverter Vacuum Pump

List of Figures

Figure Caption Page

1 TriScroll 800 Inverter Vacuum Pump . . . . . . . 6

2 Interface Drawing with Dimensions . . . . . . . 8

3 Pumping Speed Curves . . . . . . . . . . . . . . . . . 8

4 Driving Frequency vs. Analog Input . . . . . . . . 9

5 T+ Pumps List . . . . . . . . . . . . . . . . . . . . . . . 11

6 T-Unknown Pump . . . . . . . . . . . . . . . . . . . . 11

List of Tables

Table Title Page

1 Power Cord Selection . . . . . . . . . . . . . . . . . . 3

2 Circuit Breaker Requirements . . . . . . . . . . . . 3

3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . 7

4 P1 I/O-1 Interlock . . . . . . . . . . . . . . . . . . . . . 9

5 J1 - Serial Port . . . . . . . . . . . . . . . . . . . . . . . 10

6 P2 I/O-2 Port on DB9 Male Connector . . . . 10

7 T-Plus Software Variables . . . . . . . . . . . . . . 10

8 Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . 11

9 Troubleshooting Chart . . . . . . . . . . . . . . . . 13

10 Other Related Manuals . . . . . . . . . . . . . . . . 14

11 Maintenance and Tooling Kits . . . . . . . . . . 14

12 Factory Service Options . . . . . . . . . . . . . . . 15

13 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . 15

TriScroll 800 Inverter Vacuum Pump

This page intentionally left blank.

vii

TriScroll 800 Inverter Vacuum Pump

Warranty

Products manufactured by Seller are warranted against

defects in materials and workmanship for twelve (12)

months from date of shipment thereof to Customer, and

Seller’s liability under valid warranty claims is limited, at

the option of Seller, to repair, to replace, or refund of an

equitable portion of the purchase price of the Product.

Items expendable in normal use are not covered by this

warranty. All warranty replacement or repair of parts shall

be limited to equipment malfunctions which, in the sole

opinion of Seller, are due or traceable to defects in

original materials or workmanship. All obligations of

Seller under this warranty shall cease in the event of

abuse, accident, alteration, misuse, or neglect of the

equipment. In-warranty repaired or replaced parts are

warranted only for the remaining unexpired portion of the

original warranty period applicable to the repaired or

replaced parts. After expiration of the applicable warranty

period, Customer shall be charged at the then current

prices for parts, labor, and transportation.

Reasonable care must be used to avoid hazards. Seller

expressly disclaims responsibility for loss or damage

caused by use of its Products other than in accordance

with proper operating procedures.

Except as stated herein, Seller makes no warranty, express

or implied (either in fact or by operation of law), statutory

or otherwise; and, except as stated herein, Seller shall

have no liability under any warranty, express or implied

(either in fact or by operation of law), statutory or

otherwise. Statements made by any person, including

representatives of Seller, which are inconsistent or in

conflict with the terms of this warranty shall not be

binding upon Seller unless reduced to writing and

approved by an officer of Seller.

Warranty Replacement and Adjustment

All claims under warranty must be made promptly after

occurrence of circumstances giving rise thereto, and must

be received within the applicable warranty period by

Seller or its authorized representative. Such claims should

include the Product serial number, the date of shipment,

and a full description of the circumstances giving rise to

the claim. Before any Products are returned for repair

and/or adjustment, written authorization from Seller or its

authorized representative for the return and instructions

as to how and where these Products should be returned

must be obtained. Any Product returned to Seller for

examination shall be prepaid via the means of

transportation indicated as acceptable by Seller. Seller

reserves the right to reject any warranty claim not

promptly reported and any warranty claim on any item

that has been altered or has been returned by

non-acceptable means of transportation. When any

Product is returned for examination and inspection, or for

any other reason, Customer shall be responsible for all

damage resulting from improper packing or handling, and

for loss in transit, notwithstanding any defect or

non-conformity in the Product. In all cases, Seller has the

sole responsibility for determining the cause and nature of

failure, and Seller’s determination with regard thereto

shall be final.

If it is found that Seller’s Product has been returned

without cause and is still serviceable, Customer will be

notified and the Product returned at its expense; in

addition, a charge for testing and examination may be

made on Products so returned.

TriScroll 800 Inverter Vacuum Pump

This page intentionally left blank.

TriScroll 800 Inverter Vacuum Pump

DRAFT 10/9/14

Instructions for Use

General Information

This equipment is designed for use by professionals. The

user should read this instruction manual and any other

additional information supplied by Agilent before

operating the equipment. Agilent will not be held

responsible for any events that occur due to

non-compliance with these instructions, improper use by

untrained persons, non-authorized interference with the

equipment, or any action contrary to that provided for by

specific national standards.

The TriScroll™ 800 is a dry scroll vacuum pump. This

pump is suitable for pumping air or inert gases. The pump

is not intended to pump toxic, corrosive, explosive, or

particulate-forming gases.

The following paragraphs contain all the information

necessary to guarantee the safety of the operator when

using the equipment. Detailed information is supplied in

“Technical Information” on page 7.

This manual uses the following standard safety protocol:

Storage

When transporting and storing the pump, the following

environmental requirements should not be exceeded:

Unpacking and Inspection

The shipping container is a double carton.

1. After opening the outer box, remove the foam packing.

2. Slit open the inner box.

3. Lift the pump with the plywood base out of the inner

box. Attach a hoist cable capable of lifting 250 lbs

onto the eye bolt on top of the pump.

4. Remove the four bolts securing the pump frame to

the plywood base.

5. Locate the NW25 exhaust fitting and set it aside.

6. Inspect the pump for damage.

If there is shipping damage, contact the freight carrier

and your local Agilent sales office immediately.

7. Save the carton and packing materials.

Total weight of the package, including the pump, is

approximately 42 kg (92 lbs).

WARNING The warning messages are for

attracting the attention of the opera-

tor to a particular procedure or prac-

tice which, if not followed correctly,

could lead to serious injury.

CAUTION The caution messages are displayed

before procedures, which if not fol-

lowed, could cause damage to the

equipment.

NOTE The notes contain important

information taken from the text.

Temperature: –20 °C to 60 °C (–4 °F to 140 °F)

Relative humidity: 0 to 95% (non-condensing)

WARNING When unpacking the pump, be sure

not to drop it, and avoid any kind of

sudden impact or shock vibration

to it.

WARNING The TriScroll 800 weighs 32 kg

(71 lbs). To avoid injury, use proper

lifting techniques when moving the

pump.

NOTE Normal exposure to the environ-

ment cannot damage the pump.

Nevertheless, it is advisable to keep

the pump inlet closed until the

pump is installed in the system.

DRAFT 10/9/14

TriScroll 800 Inverter Vacuum Pump

Installation Requirements

Safety

Do not remove or modify any safety or insulating

equipment from the pump. To do so may create a serious

safety hazard and may void the warranty.

During operation, the following environmental

conditions should not be exceeded:

WARNING ❑This pump is designed to pump

and exhaust air and inert gases only;

it is not designed to pump explosive,

flammable, toxic, or corrosive gases.

They can cause bodily injury,

explosion, or fire.

❑Install in an area that is not

exposed to rain, steam, or excessive

humidity. They can cause electric

shock, short circuits, and severe

bodily injury.

❑Before inspecting or servicing the

pump, be sure the electrical supply

is disconnected.

❑Consult a qualified electrician

whenever wiring the pump.

❑An exhaust silencer option is

available for those applications in

which it is desirable to diminish the

sound level produced by the pump.

❑To prevent bodily injury, avoid

exposing any part of the human

body to vacuum.

❑The pump is a heavy object. To

avoid muscle strain or back injury,

use lifting aides and proper lifting

techniques when removing or

replacing.

CAUTION Although the pump can pump trace

particulates normally found in the

atmosphere, it is not designed for

process solids, chemicals, powders,

solvents, condensates, or other par-

ticulates. They can damage the

equipment, degrade its performance,

or shorten its useful life.

The pump operates in a clockwise

direction when viewed from the

motor end. (Note the arrow on the

pump frame.) Improper rotation can

cause permanent damage to the

pump.

Temperature: +5 °C to +40 °C (41 °F to 104 °F)

Relative humidity: 0 to 95% (non-condensing)

CAUTION Do not block the fan ducts because the

pump can become overheated. A pump

surface temperature in excess of 55 °C

(131 ° F) is potentially damaging. If such

conditions are observed, turn pump off

and allow to cool. Disassemble, inspect

for damage, and repair if necessary.

CAUTION To reduce the risk of electric shock,

do not expose to rain; store indoors.

Altri manuali per TriScroll 800

Indice

Altri manuali Agilent Technologies Pompa dell'acqua

Agilent Technologies

Agilent Technologies 1260 Infinity II Manuale utente

Agilent Technologies

Agilent Technologies 1260 Infinity Manuale utente

Agilent Technologies

Agilent Technologies TriScroll 300 Series Manuale utente

Agilent Technologies

Agilent Technologies X3502-64000 Manuale utente

Agilent Technologies

Agilent Technologies TwisTorr 704 FS Manuale utente

Agilent Technologies

Agilent Technologies VS PD03 Manuale utente

Agilent Technologies

Agilent Technologies Navigator TV 551 SEM Manuale utente

Agilent Technologies

Agilent Technologies MS120 Manuale utente

Agilent Technologies

Agilent Technologies PHV K Series Manuale

Agilent Technologies

Agilent Technologies MS40-S Manuale utente

Agilent Technologies

Agilent Technologies 9130037 Manuale utente

Agilent Technologies

Agilent Technologies VacIon Plus 40 Manuale utente

Agilent Technologies

Agilent Technologies Turbo-V 903 Manuale utente

Agilent Technologies

Agilent Technologies 1100 Series Manuale utente

Agilent Technologies

Agilent Technologies R1330-529 HS-16 Guida alla configurazione

Agilent Technologies

Agilent Technologies 1290 infinity Manuale utente

Agilent Technologies

Agilent Technologies DS40M Manuale utente

Agilent Technologies

Agilent Technologies 1200 series Manuale utente

Agilent Technologies

Agilent Technologies IDP 10 Manuale utente

Agilent Technologies

Agilent Technologies TwisTorr 305-ICQ Manuale utente

Agilent Technologies

Agilent Technologies G6696A Manuale utente

Agilent Technologies

Agilent Technologies X3502-64170 Manuale utente

Agilent Technologies

Agilent Technologies TV-401/301/21 NSF Manuale utente

Agilent Technologies

Agilent Technologies Turbo-V 1K-G Series Manuale utente

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente