AJAX MotionProtect Manuale utente

Posted on May 27, 2021

MotionProtect is a wireless motion detector designed for indoor use. It can

operate for up to 5 years from an in-built battery, and monitors the area within

12-meter radius. MotionProtect ignores animals, while recognizes a human from

the ﬁrst step.

MotionProtect Plus uses radio frequency scanning along with a thermal sensor,

ﬁltering interference from thermal radiation. Can operate up to 5 years from an

in-built battery.

MotionProtect (MotionProtect Plus) operates within the Ajax security system,

connected to the via the protected protocol. The communication

range is up to 1700 (MotionProtect Plus up to 1200) meters in the line of sight.

In addition, the detector can be used as a part of third-party security central

units via the or integration modules.

The detector is set up via the

for iOS Android macOS and Windows

sys

tiﬁ

user

even

roug

pus

tiﬁ

ons,

SMS

(if activated).

The Ajax security system is self-sustaining, but the user can connect it to the

central monitoring station of a security company.

Thermal PIR sensor of MotionProtect detects intrusion into protected room by

detecting moving objects whose temperature is close to the temperature of the

1. LED indicator

2. Motion detector lens

3. SmartBracket attachment panel (perforated part is required for actuating the

tamper in case of any attempt to dismantle the detector)

4. Tamper button

5. Device switch

6. QR code

sensitivity has been chosen in the settings

When the MotionProtect Plus detects motion, it will additionally carry out radio

frequency scanning of the room, preventing false actuation from thermal

interferences: air ﬂows from sun-heated curtains and louvre shutters, operating

thermal air fans, ﬁreplaces, air conditioning units, etc.

After actuation, the armed detector immediately transmits an alarm signal to the

hub, activating the sirens and notifying the user and security company.

If before arming the system, the detector has detected motion, it will not arm

immediately, but during the next inquiry by the hub.

Before starting connection:

Only users with administrator rights can add the device to the hub

How to connect the detector to the hub:

1. Following the hub manual recommendations, install the .

Create an account, add the hub to the application, and create at least one

room.

2. Switch on the hub and check the internet connection (via Ethernet and/or

GSM network).

3. Make sure that the hub is disarmed and does not update by checking its

status in the app.

1. Select theAdd Deviceoption in the Ajax application.

2. Name the device, scan/write manually the QR Code (located on the body

For detection and pairing to occur, the detector should be located within the

coverage of the wireless network of the hub (at a single protected object).

Request for connection to the hub is transmitted for a short time at the moment

of switching on the device.

If the detector failed to connect to the hub, switch off the detector for 5 seconds

3. Select Add — the countdown will begin.

4. Switch on the device.

of the detector statuses in the list depends on the device inquiry time set in the

hub settings(default value is 36 seconds).

To connect the detector to a third party security central unit with the

or integration module, follow the recommendations in the

manuals of these devices.

Parameter Value

Temperature Temperature of the Detector. Measured on the

processor and changes gradually

Jeweller Signal Strength Signal strength between the hub and the

detector

Connection Connection status between the hub and the

detector

Battery Charge

Battery level of the device. Displayed as a

percentage

Lid The tamper mode of the detector, which reacts

to the detachment of or damage of the body

Delay When Entering, sec Delay time when entering

Delay When Leaving, sec Delay time when exiting

ReX Displays the status of using the ReX range

extender

Sensitivity Sensitivity level of the motion sensor

1. Devices

2. MotionProtect | MotionProtect Plus

Temporary Deactivation

deactivation function:

Firmware Detector ﬁrmware version

Device ID Device identiﬁer

Setting Value

First ﬁeld Detector name, can be edited

Room Selecting the virtual room to which the device is

assigned

Delay When Entering, sec Selecting delay time when entering

Delay When Leaving, sec Selecting delay time on exit

Delays in night mode Delay turned on when using night mode

No — the device operates normally and

transmits all events.

Lid only — the hub administrator has

disabled notiﬁcations about triggering on

the device body.

Entirely — the device is completely excluded

from the system operation by the hub

administrator. The device does not follow

system commands and does not report

alarms or other events.

By number of alarms — the device is

automatically disabled when the number of

alarms is exceeded (speciﬁed in the settings

for Devices Auto Deactivation). The feature

is conﬁgured in the Ajax PRO app.

1. Devices

2. MotionProtect | MotionProtect Plus

3. Settings

Alarm LED indication

Sensitivity

Choosing the sensitivity level of the motion

sensor.

For MotionProtect:

For MotionProtect Plus:

Always active If active, the detector always registers motion

Alert with a siren if motion detected If active, added to the systemare

activated when the motion detected

Jeweller Signal Strength Test Switches the detector to the signal strength test

mode

Detection Zone Test Switches the detector to the detection area test

Attenuation Test

Switches the detector to the signal attenuation

test mode (available in detectors with ﬁrmware

version 3.50 and later)

Allows the user to disconnect the device

without removing it from the system.

High — for premises with a minimum

amount of obstacles, motion is detected as

quickly as possible

Medium — for premises with potential

obstacles (windows, air conditioner, heating

element, etc)

Low — ignore pets weighing up to 20 kg and

up to 50 cm tall

High — the detector disregards cats (under

25 cm)

Medium — disregards small dogs (under 35

cm)

Low — disregards animals under 50 cm.

Temporary Deactivation

The system can also automatically disable

devices when the set number of alarms is

exceeded.

User Guide Opens the User Guide

Unpair Device Disconnects the detector from the hub and

deletes its settings

Before using the detector as a part of the security system, set up the suitable

sensitivity level.

Switch the Always Active if the detector is located in a room requiring 24-hour

control. Regardless of whether the system is set in the armed mode, you will

receive notices of any detected motion.

If any motion is detected, the detector activates the LED for 1 second and

transmits an alarm signal to the hub and then to the user and central monitoring

station (if it is connected).

Event Indication Note

Turning on the detector Lights up green for about one

second

Detector connection to the

Lid only

—

the system will ignore only

notiﬁcations about the triggering of the

device tamper button

up and goes off green

manual

The Ajax security system allows conducting tests for checking the functionality

of connected devices.

The tests do not start immediately but within a period of 36 seconds when using

the standard settings. The time of the start depends on the settings of the

detector polling period (the paragraph on Jeweller settings in the hub settings).

The controlled area and the efﬁciency of the security system depends on the

location of the detector.

The device developed only for indoor use.

Location of MotionProtect depends on the remoteness from the hub and

presence of any obstacles between the devices hindering the radio signal

transmission: walls, inserted ﬂoors, large-size objects located within the room.

Check the signal level at the installation location

If the signal level is at one bar, we cannot guarantee stable operation of the

security system. Take all possible measures to improve the quality of the signal!

As a minimum, move the device – even 20 cm shift can signiﬁcantly improve the

quality of reception.

If after moving the device still has a low or unstable signal strength, use the

The direction of the detector lens should be perpendicular to the probable way of

intrusion into the room

Make sure that any furniture, domestic plants, vases, decorative or glass

structures do not block the ﬁeld of view of the detector.

We recommend installing the detector at the height of 2,4 meters.

If the detector is not installed at the recommended height, this will reduce the

area of the motion detection zone and impair the operation of the function of

ignoring animals.

Altri manuali per MotionProtect

Questo manuale è adatto per i seguenti modelli

Altri manuali AJAX Sensore di sicurezza

AJAX

AJAX CombiProtect Manuale utente

AJAX

AJAX GlassProtect Fibra Manuale utente

AJAX

AJAX GlassProtect Manuale utente

AJAX

AJAX MotionProtect Manuale utente

AJAX

AJAX DoorProtect Plus Manuale utente

AJAX

AJAX FireProtect 2 (Heat) Jeweller Manuale utente

AJAX

AJAX MotionCam Manuale utente

AJAX

AJAX CombiProtect Manuale utente

AJAX

AJAX FireProtect 2 Jeweller Manuale utente

AJAX

AJAX MotionCam PhOD Jeweller Manuale utente

AJAX

AJAX LeaksProtect Manuale utente

AJAX

AJAX FireProtect 2 Manuale utente

AJAX

AJAX DoorProtect Plus Manuale utente

AJAX

AJAX GlassProtect Manuale utente

AJAX

AJAX MotionProtect Manuale utente

AJAX

AJAX LeaksProtect Manuale utente

AJAX

AJAX FireProtect 2 (CO) Jeweller Manuale utente

AJAX

AJAX DualCurtain Outdoor Manuale utente

AJAX

AJAX DoorProtect Manuale utente

AJAX

AJAX MotionProtect Manuale utente

AJAX

AJAX DoorProtect Manuale utente

AJAX

AJAX CombiProtect Manuale utente

AJAX

AJAX FireProtect 2 Jeweller Manuale utente

AJAX

AJAX LeaksProtect Manuale utente

Manuali Sensore di sicurezza popolari di altre marche

THORLABS

THORLABS PDA10JT Manuale utente

Waeco

Waeco UV-DETECT Manuale utente

Intermatic

Intermatic IOS-DSIMF Manuale utente

urmet domus

urmet domus 1083 Manuale utente

Siemens

Siemens AZL66 Series Manuale utente

BTI

BTI Profiline Multi Finder Manuale utente

Challenger

Challenger SL01 Manuale utente

DMP Electronics

DMP Electronics 1122INT Manuale utente

Rielta

Rielta Ladoga MK-RK Manuale utente

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuale utente

Bosch

Bosch DS835 Manuale utente

DBI SALA

DBI SALA EZ Stop Manuale dell'operatore

Lamptime

Lamptime ST05C Manuale utente

Ubiquiti

Ubiquiti MFI-MSC Manuale utente

Subsite

Subsite 910R Istruzioni per l'installazione

Satel

Satel OPAL Pro Manuale utente

Aleph

Aleph XC-1XTEU Manuale utente

Pima

Pima LARIS QUAD Manuale utente