Algo 8190 Manuale utente
8190 SIP Classroom Speaker FW 1.7.3
8190 SIP Classroom Speaker
Firmware Version 1.7.3
User Guide
Document 90 00097A
05/22/2019
Page 1
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454 3792
8190 SIP Classroom Speaker FW 1.7.3
Table of Contents
IMPORTANT SAFETY INFORMATION...................................................................................................... 4
O ER IEW.................................................................................................................................................. 6
Introduction........................................................................................................................................... 6
Key Features......................................................................................................................................... 6
Reset Button......................................................................................................................................... 8
SETUP AND INSTALLATION..................................................................................................................... 9
Getting Started - Quick Install & Test.................................................................................................. 9
Wall Mounting..................................................................................................................................... 10
Programming and Configuration....................................................................................................... 10
Inputs/Outputs.................................................................................................................................... 11
FEATURES................................................................................................................................................ 12
SIP Paging: One 8190......................................................................................................................... 12
SIP Ring Event.................................................................................................................................... 12
Multicast Overview............................................................................................................................. 12
SIP Paging: Multiple 8190s (Using Multicast)...................................................................................13
SIP Paging: Multiple Speakers (Using Individual SIP extensions).................................................13
SIP Activated Notification Alerts....................................................................................................... 14
Background Music Streaming...........................................................................................................14
PolycomTM Group Paging................................................................................................................. 14
TLS for SIP Signaling and Provisioning...........................................................................................15
WEB INTERFACE BASIC SETTINGS......................................................................................................18
Web Interface Login............................................................................................................................18
Status................................................................................................................................................... 18
Basic Settings Tab – SIP.................................................................................................................... 18
Basic Settings Tab – Features........................................................................................................... 20
Basic Settings Tab – Clock................................................................................................................ 22
Basic Settings Tab – Multicast.......................................................................................................... 22
Basic Settings Tab – Multicast (Slave Settings)..............................................................................23
WEB INTERFACE ADDITIONAL FEATURES..........................................................................................25
Additional Features Tab – Input/Output............................................................................................25
Additional Features Tab – Emergency Alerts...................................................................................29
Additional Features Tab – More Ring Extensions...........................................................................29
WEB INTERFACE AD ANCED SETTINGS.............................................................................................30
Advanced Settings Tab – Network....................................................................................................30
Advanced Settings Tab – Admin....................................................................................................... 32
Advanced Settings Tab – Time.......................................................................................................... 35
Advanced Settings Tab – Provisioning.............................................................................................36
Advanced Settings Tab – File Manager............................................................................................38
Advanced Settings Tab – Advanced Audio......................................................................................39
Advanced Settings Tab – Advanced SIP..........................................................................................40
Advanced Settings Tab – Advanced Multicast.................................................................................42
WEB INTERFACE SYSTEM..................................................................................................................... 44
System Tab – Maintenance................................................................................................................ 44
System Tab – System Log................................................................................................................. 45
Document 90 00097A
05/22/2019
Page 2
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454 3792
8190 SIP Classroom Speaker FW 1.7.3
WIRING CONNECTIONS.......................................................................................................................... 46
Network Connection........................................................................................................................... 46
Connecting Input Devices.................................................................................................................. 46
Blue LED Indicator.............................................................................................................................. 47
SPECIFICATIONS..................................................................................................................................... 48
FCC COMPLIANCE STATEMENT............................................................................................................ 50
Document 90 00097A
05/22/2019
Page 3
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454 3792
8190 SIP Classroom Speaker FW 1.7.3
Important Safety Information
Important Safety Information
This product is powered by a certified limited power source (LPS), Power over Ethernet
(PoE); through CAT5 or CAT6 connection wiring to an IEEE 802.3at PoE+ or 802.3af
compliant network PoE switch. The product is intended for installation indoors. All wiring
connections to the product must be in the same building. If the product is installed beyond
the building perimeter or used in an inter building application, the wiring connections must
be protected against overvoltage/transient. Algo recommends that this product is installed
by a qualified electrician.
If you are unable to understand the English language safety information then please
contact Algo by email for assistance before attempting an installation
Consignes de Sécurité Importantes
Ce produit est alimenté par une source d’alimentation limitée certifiée (alimentation par
Ethernet); des câbles de catégorie 5 et 6 joignent un commutateur réseau à alimentation
par Ethernet homologué IEEE 802.3at PoE+ or 802.3af. Le produit est conçu pour être
installé à l’intérieur. Tout le câblage rattaché au produit doit se trouver dans le même
édifice. Si le produit est installé au delà du périmètre de l’édifice ou utilisé pour plusieurs
édifices, le câblage doit être protégé des surtensions transitoires. Algo recommande qu’un
électricien qualifié se charge de l’installation de ce produit.
Si vous ne pouvez comprendre les consignes de sécurité en anglais, veuillez
communiquer avec Algo par courriel avant d’entreprendre l’installation au
Información de Seguridad Importante
Este producto funciona con una fuente de alimentación limitada (Limited Power Source,
LPS) certificada, Alimentación a través de Ethernet (Power over Ethernet, PoE); mediante
un cable de conexión CAT5 o CAT6 a un conmutador de red con PoE en cumplimiento
con IEEE 802.3at PoE+ or 802.3af. El producto se debe instalar en lugares cerrados.
Todas las conexiones cableadas al producto deben estar en el mismo edificio. Si el
producto se instala fuera del perímetro del edificio o se utiliza en una aplicación en varios
edificios, las conexiones cableadas se deben proteger contra sobretensión o corriente
transitoria. Algo recomienda que la instalación de este producto la realice un electricista
calificado.
Si usted no puede comprender la información de seguridad en inglés, comuníquese con
Algo por correo electrónico para obtener asistencia antes de intentar instalarlo:
Document 90 00097A
05/22/2019
Page 4
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454 3792
8190 SIP Classroom Speaker FW 1.7.3
Wichtige Sicherheitsinformationen
Dieses Produkt wird durch eine zertifizierte Stromquelle mit begrenzter Leistung (LPS –
Limited Power Source) betrieben. Die Stromversorgung erfolgt über Ethernet (PoE –
Power over Ethernet). Dies geschieht durch eine Cat 5 Verbindung oder eine Cat 6
Verbindung zu einer IEEE 802.3at PoE+ or 802.3af konformen Ethernet Netzwerkweiche.
Das Produkt wurde konzipiert für die Installation innerhalb eines Gebäudes. Alle
Kabelverbindungen zum Produkt müssen im selben Gebäude bestehen. Wenn das
Produkt jenseits des Gebäudes oder für mehrere Gebäude genutzt wird, müssen die
Kabelverbindungen vor Überspannung und Spannungssprüngen geschützt werden. Algo
empfiehlt das Produkt von einem qualifizierten Elektriker installieren zu lassenv.
Sollten Sie die englischen Sicherheitsinformationen nicht verstehen, kontaktieren Sie bitte
Algo per Email bevor Sie mit der Installation beginnen, um Unterstützung zu erhalten.
Algo kann unter der folgenden E Mail Adresse erreicht werden:
安全须知
本产品由认证的受限电源（LPS）以太网供电（PoE）通过 CAT5 或CAT6 线路联接至
IEEE 802.3at PoE+ or 802.3af 兼容的 PoE 网络交换 供电。本产品适用于室内或建筑物周
边安装。所有联接本产品的线路必须源自同一建筑物。本产品如需用于超出建筑物周边范
围或跨建筑物的安装线路联接部分必须有过压和瞬态保护。Algo 建议本产品由专业电工
安装。
如果您对理解英文版安全须知有问题安装前请通过电子邮件和 Algo 联
EMERGENCY COMMUNICATION
If used in an emergency communication application, the 8190 SIP Classroom Speaker
should be routinely tested. SNMP supervision is recommended for assurance of proper
operation. Contact Algo for other methods of operational assurance.
DRY INDOOR LOCATION ONLY
The 8190 SIP Classroom Speaker is intended for dry indoor locations only. For outdoor
locations Algo offers weatherproof speakers and strobe lights.
CAT5 or CAT6 connection wiring to an IEEE 802.3at PoE+ or 802.3af compliant
network PoE switch must not leave the building perimeter without adequate
lightning protection.
No wiring connected to the 8190 SIP Classroom Speaker may leave the building
perimeter without adequate lightning protection.
Document 90 00097A
05/22/2019
Page 5
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454 3792
8190 SIP Classroom Speaker FW 1.7.3
Overview
Introduction
The 8190 SIP Classroom Speaker is a SIP compliant & multicast capable IP speaker
designed for education but suitable for any application that requires crisp clear voice
paging, loud ringing, and alert/notification with a high visibility clock. The 8190 can be
integrated with any Communication Server (hosted or enterprise) that supports 3rd party
SIP endpoints or multicast.
Instead of one speaker, the 8190 uses a multi speaker line array for improved sound
distribution in classrooms. Controlled dispersion in the vertical axis reduces reflections
from floor and ceiling and provides more consistent direct sound levels for listeners at
different distances from the speaker.
The 8190’s feature set supporting 50 SIP extensions provides near infinite zoning
capabilities, and 10 SIP extensions activating audio wav files from memory enable loud
ringing, informational and emergency notification.
For voice paging, the 8190 is assigned a Page extension. When this SIP extension is
called, the 8190 will auto answer and play the caller’s voice announcement over the
speaker. The 8190 supports G.722 wideband HD Voice for enhanced intelligibility and
clarity.
For loud ringing a separate Page extension can be assigned. When this SIP extension is
called the 8190 will play a WAV file (tone, announcement, etc.) over the speaker. Several
ringtones are included in the 8190 and custom WAV files may also be uploaded (e.g.
safety, security, emergency alerts).
Consistent with other Algo IP Speakers, the 8190 includes a microphone for monitoring
and adapting to ambient noise levels. This means voice paging and bell tones are always
heard but never too loud. The microphone can also be enabled for hands free talkback.
Unlike other Algo IP Speakers, the 8190 has an integrated digital clock, integrated call
button, and entrance security door control capability.
The 8190 is configured using central provisioning features, or by accessing a web
interface using browsers such as Google Chrome, Firefox, or Internet Explorer.
Key Features
SIP Extensions
The 8190 connects to an on premise or hosted communication server in the same way as
a SIP telephone. To register the 8190 with the server requires the following information:
1. IP address (e.g. 192.168.1.1) or domain name (e.g. myserver.com) of the SIP
Server
2. SIP extension (e.g. 3790)
Document 90 00097A
05/22/2019
Page 6
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454 3792
8190 SIP Classroom Speaker FW 1.7.3
3. Authentication ID
4. Password
The 8190 supports two SIP extensions which behave differently – RING and PAGE. One
or both may be used depending on the application. If the RING extension is called the
8190 will not answer. Instead, it will play the selected WAV file until the ringing stops.
Typically the RING extension is programmed as part of a hunt group so that it receives a
ring signal simultaneously with one or more phones to function as a loud ringer in noisy or
large areas.
If the PAGE extension is called, the 8190 will answer and allow paging over its internal
speaker. When the 8190 answers it will play a configurable tone to the caller so they know
when they can begin speaking. The same tone is also played over the speaker before the
announcement. If Paging to a single 8190, talkback may be enabled using the integrated
microphone. The audio direction is determined by the speech activity of the caller.
Speaker Array Technology
The 8190 uses a multi speaker line array for improved sound distribution in classrooms.
Controlled dispersion in the vertical axis reduces reflections from floor and ceiling and
provides more consistent direct sound levels for listeners at different distances from the
speaker. Wideband G.722 HD codec support provides improved speech intelligibility for
voice paging and audio notification.
Multicasting
Allows multiple units to simultaneously play Ring or Page audio. 8190 can be configured
as a multicast ‘Slave’ device to receive audio stream from a multicast ‘Master’ device. Any
number/combination of Algo IP speaker, paging adapter, or strobe endpoint can be
configured as multicast ‘Slaves’. This feature provides scalability without requiring each
endpoint Slave to be registered with a SIP extension.
PolycomTM Group Paging
The 8190 support Polycom Group Paging. The 8190 can be added to a Polycom Group
Page so that voice paging is heard over Polycom telephone speakers and overhead
paging simultaneously.
Ambient Noise Compensation
The 8190’s can automatically adjusts loud ring and paging volume to compensate for
background ambient noise. If ‘Ambient Noise Compensation’ is enabled, the alert volume
will get louder or quieter by the same dB level as the ambient noise measured just prior to
the alert.
Configuration & Provisioning
Configuration can be done through a web interface control panel or by using the program
buttons on the back of the unit. Central provisioning may also be used to allow units to be
Document 90 00097A
05/22/2019
Page 7
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454 3792
8190 SIP Classroom Speaker FW 1.7.3
pre configured for a specific server prior to deployment in the field. Configuration files are
automatically downloaded from a server (via TFTP, FTP, HTTP, HTTPS) using DHCP.
Reset Button
A recessed reset button (RST) on the back can be used to reset the 8190 SIP Classroom
Speaker at time of power up. To reset, reboot or power cycle the 8190. Wait until the blue
LED flashes and then press and hold the reset button until the blue LED begins a double
flash pattern. Release the reset button and allow the unit to complete its boot process. Do
not press the reset button until the blue LED begins flashing.
A reset will set all configuration options to factory default including the password.
Once booting has completed, pressing the reset button will cause the speaker to
announce its IP address over the speaker.
Document 90 00097A
05/22/2019
Page 8
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454 3792
8190 SIP Classroom Speaker FW 1.7.3
Setup and Installation
Getting Started - Quick Install & Test
This guide provides important safety information which should be read
thoroughly before permanently installing the speaker.
1. Connect the 8190 SIP Classroom Speaker to an IEEE 802.3at PoE+ or 802.3af
compliant PoE network switch. The blue light at the top will remain on until boot up is
completed – about 30 seconds.
2. After the blue LED turns off and you hear a tone, press the reset switch (RST) button
on the back of the unit to hear the IP address over the speaker. The IP address may
also be discovered by downloading the Algo Locator Tool to find Algo devices on
your network: www.algosolutions.com/locator
3. Mount the speaker per the instructions in the next section
4. Access the 8190 web page by entering the IP address into a browser (Chrome,
Firefox etc.) and login using the default password: algo
5. Enter the IP address for the SIP server into the SIP Domain field under the Basic
Settings > SIP tab.
6. Enter the Ring and/or Page SIP extension and credentials. Leave the credentials
blank for either extension if there is no intended use to have both registered.
(Note: The speaker supports multiple Ring, Emergency Alert, and Page SIP
extensions. The Page extension auto answers for voice announcements. The Ring
and Emergency Alert extensions will play a WAV file over the speaker without
answering.)
7. Make a test call from a telephone to the speaker for one or both extensions. The
Page SIP extension should auto answer, play the default pre announce WAV file,
and open a speech path to make a voice announcement. The Ring SIP extension will
play the default WAV file from those available in device memory.
Document 90 00097A
05/22/2019
Page 9
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454 3792
8190 SIP Classroom Speaker FW 1.7.3
Wall Mounting
Mount the wall bracket securely. Once the wall bracket is secure, slides the 8190 onto the
bracket. Secure the 8190 to the wall bracket with the provided four screws.
Programming and Configuration
After connecting the 8190 to a network PoE, the blue indicator light at the top will turn on
during initialization. The 8190 will then attempt to obtain an IP address from the DHCP
server. If there is no DHCP server or the attempt was unsuccessful, the 8190 will default
to the static IP address 192.168.1.111.
Note: If you don’t have a PoE switch you’ll need a PoE or PoE+ injector installed
between the 8190 and the network switch. The PoE injector will supply 48 Vdc to
the 8190. Most PoE injectors are capable of providing more power than the 8190
requires (12.95 W). Ensure that the PoE injector is fully compliant to the IEEE
802.3at PoE+ or 802.3af standard.
After a successful boot up the blue LED will turn off and you will hear a tone, and the
speaker will have obtained an IP address.
Press the reset button button (RST) momentarily to hear the IP address over the speaker
and press it again to stop playing the IP address over the speaker.
The IP address may also be discovered by downloading the Algo locator tool to find Algo
devices on your network: www.algosolutions.com/locator
Document 90 00097A
05/22/2019
Page 10
Algo Communication Products Ltd
4500 Beedie St Burnaby BC Canada V5J 5L2
www.algosolutions.com
(604) 454 3792
Indice
Altri manuali Algo Altoparlanti
